Fully maintained, including volume disassembly and cleaning! A limited edition of 200 units in the ULTIMATE series that revives the sound of the Golden Age of Lux. It is an improved model while inheriting the style of the CL-36. Delicate high frequencies are added to the soft, thick tone typical of a vacuum tube. There is a repair mark on the side corner of the wood case (Murakoshi Yoichi)
Maintenance information: 2024.9.5 maintenance (main volume disassembly, cleaning repair and grease up treatment, front lamp, vacuum tube 12AU7, replacement of 2 spark killers, vacuum tube socket and RCA jack caulking repair, operation check with AC 100V)
Accessories: instruction manual, original box
Main specifications: vacuum tube using phono 2 systems 12AX7 x 4, 12AU7 x 6, 12H7A x 1 W490 x H201 x D294 mm 11.5 kg
Maintained! An attractive limited-edition vacuum tube amplifier with an elegant atmosphere and fresh playback sound! The medium and low frequencies are very responsive, and the high frequencies have wonderful stretch and afterglow, and it makes me listen powerfully to performances by full orchestras, etc. There are no conspicuous scars (Sasaki Shota)
Maintenance information: 2024.9.7 maintained (common/volume disassembly, cleaning repair, resistance 1W defect replacement, 1 x 2, spark killer deterioration replacement 2 pieces, vacuum tube socket and RCA jack caulking repair, RCA jack defect replacement/resistance 1W defective replacement, etc. Operation checked with AC100V, rated output 85W SP: 8Ω)
Accessories: none
Main specifications: Effective output 60 W vacuum tube/KT88 x 4, E82CC x 4, E82CC x 2 W402 x H175 x D253 mm 17.5 kg
Maintained! LUXMAN 70th anniversary signature model. The standard EL34 push-pull configuration has an OY transformer, and is designed so that you can fully enjoy the flavor of luxe stone. Using an unprecedented high-rigidity chassis, it also has an outstanding sense of luxury. This is a 90s vacuum tube premain with a good balance of range width, thickness, and tone. There is a scuff on the front knob (Kojima Yosuke)
Maintenance information: 2024.1.13 maintained (rotary switch replacement, 2 output tubes replaced due to right channel bias, double channel drive stage socket replacement, switch contact disassembly, cleaning volume, cleaning knob, milling correction, vacuum tube pin cleaning bias adjustment, output voice check, sound check at 8 Ω load)
Accessories: copy of instruction manual, power cable
Main specifications: output 30W+30W (6Ω) phono (mm) 2.5mV/47kΩ vacuum tube EL34 (6CA7) x 4, 12AU7 x 4, 12BH7A x 2 W430 x H209 x D387 mm weight 22 kg
The price has been reduced! 2024/9/1 sales price 59,800 yen Maintained. An eye-catching Lax pre-main amplifier with a unique indicator. It is a traditional lackstone, and the soft and warm mid-low range like a vacuum tube is attractive. The speakers, which have a solid sound quality, also play softly. There is a slight gap in the scale on the BASS dial. The exterior has rolled up veneer, scratches, and dullness. Serial 11401165 (Yonejima Satoshi)
Maintenance information: 2024.9.1 Maintained (12 road deteriorated transistors and 18 capacitors replaced. Disassemble the switches and polish the contacts and apply contact cleaner. Main volume disassembly contact polishing. I/O pin jack polish. (Deterioration has been seen on the speaker terminals, and the plastic is discolored and scraped, but there is no problem with operation)
Accessories: No accessories
Main specifications: 40W+40W (8Ω) W443 × H153 × D273 mm 9.3 kg
The price has been reduced! 2024/9/5 sales price 148,000 yen Manufacturer maintained! The L-550X is the successor to the L-550, a masterpiece premain amplifier with pure Class A operation. Compared to the initial model, there are no changes other than the addition of an input terminal, and it plays back bright and spacious lacktones. MC compatible, which is great for analog users. The exterior is dull and there are chips and scratches on the cabinet top and sides. Serial B4401324 (Takahashi Nobuyuki)
Maintenance information: 2024.9.5 Luxman headquarters maintained (Rch power transistor replacement Lch power transistor replacement resistor, driver transistor, capacitor, fuse replacement power amplifier base solder correction pilot lamp replacement
Input selector SW contact cleaning inspection running test comprehensive adjustment operation characteristic test)
Accessories: copy of instruction manual
Main specifications: 50W+50W (8Ω) pre-main separation function W453 x H174 x D470 mm 20 kg
Maintained. LUXMAN AD8000 transformer adapter and 8030 step-up transformer set This step-up transformer is compatible with low impedance cartridges. A masterpiece that makes full use of Luxman transformer technology. You can see a feeling of use such as appearance, dullness, scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.9.3 Maintained (rewired after cleaning the changeover switch contacts)
Accessories: none
Main specifications: Compatible cartridge 1.5 to 3.5 ohms, boost ratio 1:32 (30db), W60 x H75 x D122 mm, approx. 489 g (actual measurement)
The price has been reduced. 2024/9/5 sales price 248,000 yen Maintained by the manufacturer! This is a reprint model of the first SQ38D, which was sold in a limited edition of 500 units. The output tube uses 6BQ5, which is still easy to obtain. It combines thick mid-range lux tones with clear sound. There are plenty of charms, such as beautiful wood cabinets and machined aluminum knobs unique to the company (Daiki Goto)
Maintenance information: 2024.9.5 Luxman headquarters maintained (6BQ5 noise, 2 replaced. Power switch rattle fixed. Some contacts have been cleaned and readjusted.)
Accessories: instruction manual, original box
Main specifications: 12W+12W 6BQ5 push-pull OY transformer input terminals PHONO x 2 (MM, MC 1 each) /AUX x 3 output terminal speaker x 1 (4Ω, 6Ω, 8Ω selection) W465 x H275 x D175 mm 16.0 kg
The disposal price has been reduced (member prices are not applicable). 2024/8/30 sales price 198,000 yen Maintained! A grade vacuum tube power amplifier using the 6550A, which has an impressive high quality and stable appearance. Among lax, which has a reputation for its smoothness, the rich flavor is particularly attractive. It is a model where you can enjoy delicate tones and well-balanced mid and low frequencies. ※Side panels are out of stock (Daiki Goto)
Maintenance information: 2024.8.31 maintained (V4 board instability → re-soldering treatment) 2024.8.10 maintained (board solder instability repair · subchassis mounting nut+washer and screw missing parts added · block capacitor 47 μF x 3 deterioration replacement · 2 electrolytic capacitors 1000 μF deterioration replacement · 1 W and 1/2 W deterioration exchange 3 · vacuum tube 6CG7 light emission defect replacement · vacuum tube socket and RCA jack caulking Repairs* Operation has also been checked with AC 100V (measured with rated output measured at 50W/8Ω)
Accessories: instruction manual
Main specifications: effective output 40W+40W (8Ω) KT88 push-pull self-biased vacuum tube 6550A x 4/6CG7 x 2/12 AU7A x 2 W434 x H176 x D252 mm 19 kg
Comes with original box, good condition! A rare Luxman line transformer is now in stock. The boosting effect is 1:1.3 times, and analog-like tone and depth can be obtained. The exterior is in good condition with no conspicuous scratches (Fujisawa Yukishi)
Maintenance information: 2024.9.2 operation confirmed
Accessories: instruction manual, original box, ground wire
Main specifications: W188 x H65 x D1250 mm weight 2.0 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/8/25 sales price 12,000 yen. RCA cable, 0.7 meter pair, 6N conductor, is a cable with excellent resolution. The goodness of the material is well reflected in the sound. There is dullness (Takasaki Atsushi)
Maintenance information: 2024.8.23 continuity confirmed
Accessories: none
The remote control is now in stock. Speaker selector that can be switched by operating a remote control. It is a 3-system switchable type using a large speaker relay, and can also be switched with the main unit button. There is a slight feeling of use on the exterior. Serial G21001196 (Fujisawa Yukishi)
Maintenance information: 2024.9.3 continuity confirmed
Accessories: AC adapter, remote control
Main specifications: 3-system switching W297 x H79 x D137 mm 1.8 kg
USB cable 1.5m USB-A/B type transmission line has the same respective core structure to minimize phase shift in the high frequency region. Uses core wire taping with Japanese paper, which has an antistatic effect. It's a soft sound with a moderate sense of localization (Kojima Yosuke)
Accessories: none
The capacitors, switches, and volume were thoroughly maintained in 2024/7! Lux's early transistor pre-main amplifier. The vocals stand out based on a faint warm sound, and you can feel the thickness of the mid-range. It has an appeal not found in current models. The exterior has line damage, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.8.24 Operation confirmed
2024.7.4 Maintained (main volume, Treble/Bass, balance volume cleaning. Rotary switch contact cleaning for source, stereo mode, etc. Contact cleaning for all toggle switches, such as Att/Normal. The capacitance and ESR values of the electrolytic capacitors in the board were inspected, and 26 deteriorated electrolytic capacitors were replaced. Pre/Main slide switch contact cleaning. Pilot lamp preventive replacement Clean the front panel and knobs and clean the interior and RCA terminals. (Offset, idle adjustment)
Accessories: power cable
Main specifications: 30W+30W (8Ω) W451 × H148 × D268 mm 10.5 kg
L-507 wood cabinet If you are looking for one, why don't you do it (Daiki Goto)
Accessories: none
Main specifications: W450 x H160 x D268 mm, weight 2.1 kg (actual measurement)
Maintained! A power amplifier with a separate name for the main part of the SQ38F series. The natural, smooth sound quality with a high sense of transparency is attractive. You can relax and enjoy classical music and vocals in a natural way. The deep sound quality that cannot be expressed with the latest vacuum tube amplifiers is exceptional. There is a slight feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.8.2 maintenance (first stage vacuum tube replacement) 2024.5.29 maintenance (vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, semi-fixed VR, fuse holder replacement. SW/VOL disassembly contacts are re-polished, and grease is applied to prevent oxidation and sulfidation. Input/output waveform confirmation, load test (8Ω load 1kHz 30W/30W), input/output waveform confirmation, sound output check performed.)
Accessories: instruction manual (copy)
Main specifications: output 30W+30W dimensions W410 x H160 x D205 mm weight 13.8 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/6/4 sales price 29,800 yen ※The power supply has been converted to Megane Inlet. Maintained! Head amplifier for Luxman MC cartridges. This head amplifier has no corners and is characterized by a smooth, sit-down sound. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.4 Maintained (GAIN switch disassembly contact polishing, contact grease application after eyelet correction. Transistor replacement for each circuit (DC amplifier, MUTING, power supply). (Running test)
Accessories: power cable
Main specifications: MC type cartridge head amplifier with PASS input impedance/100Ω 20dB/30dB switching W138 x H78 x D305 mm 2.7 kg
Maintained! Lax's thin premain. It has a thick, smooth sound typical of a lux, and it seems that you can enjoy it smoothly with a small bookshelf speaker. The exterior is dull and has line marks (Oikawa Tetsuji)
Maintenance information: 2024.7.18 Maintained (disassemble switches, polish contacts and apply contact cleaner. Volume contact correction. Main amplifier circuit board solder correction. I/O pin jack polish (This unit does not have a protection circuit, so there may be a popping sound when the power is turned on and off)
Accessories: copy of instruction manual
Main specifications: 35W+35W (8Ω) W435×H85×D300mm 7kg
Maintenance was carried out with attention to detail, such as replacing capacitors and replacing SP terminals! A kit model of a power amplifier using a 50CA10 3-pole output tube and an OY15 type output transformer, composed of circuits and parts conforming to the MQ60 type, which has been evaluated by LUXMAN. The sound of a vacuum tube has a sense of volume that seems to meet expectations, and it gently envelops you. The sound, which doesn't require scale, is particularly unique, and the slight thickness that spreads from below the mid-range makes you feel comfortable. The exterior has rust, oxidation, and scratches. Serial 574788 (Tamura Eiji)
Maintenance information: 2024.7.11 Maintained (vacuum tube sockets, block capacitors, electrolytic capacitors, oil capacitors, SP and RCA terminals, semi-fixed VR, fuse holder replacement. Check input/output waveforms and perform sound output checks. Impedance switching SW, gain VOL complete disassembly, contact refinement, and application of grease to prevent oxidation and sulfidation. Input/output waveform confirmation, load test (1 kHz sine wave, at 8 ohm load: 27W+27W, actual measurement), sound output test)
Accessories: No accessories
Main specifications: 30W+30W 50CA10 push pull W410 x H160 x D205 mm 13.8 kg
Fully restored! A kit model of a power amplifier using a 50CA10 3-pole output tube and an OY15 type output transformer, composed of circuits and parts conforming to the MQ60 type, which has been evaluated by LUXMAN. The sound of a vacuum tube has a sense of volume that seems to meet expectations, and it gently envelops you. The sound, which doesn't require scale, is particularly unique, and the slight thickness that spreads from below the mid-range makes you feel comfortable. The exterior is dull, rust, abrasions, etc., and there is a feeling of use (Ryo Mizusaki)
Maintenance information: 2024.6.21 Maintained (vacuum tube sockets, block capacitors, electrolytic capacitors, oil capacitors, SP and RCA terminals, semi-fixed VR, fuse holder replacement. Load test (8Ω load 1kHz 24.5W+24.5W), input/output waveform confirmation, impedance switching SW/gain VOL disassembly contact refinement, oxidation and vulcanization prevention grease coating. Input/output waveform confirmation, load test (1 kHz sine wave, 8 ohm load: 28 W+28 W, actual measurement), sound output test)
Accessories: copy of instruction manual
Main specifications: 30W+30W 50CA10 push pull W410 x H160 x D205 mm 13.8 kg
Power transformer used in MQ60 vacuum tube amplifiers Primary: 100V Secondary: 360V/280mA 100V/350mA 60V/70mA CT-6.3 V/2A W104 × H97 x D87 mm approx. 4.3 kg (actual measurement, not including protrusions) (Yosuke Kojima)
※Shipping service. No. 58 Special Feature = 3rd “THE STATE OF THE ART: Supreme Component” Award Selection/New JBL 4345 Detailed Report/EMT927 vs. Torrance Reference/Listen to the Tannoy SRM Series/Infinity “IRS” Anatomy/1981.4.15 issued. Posted models: JBL/4345BWX MCINTOSH/MC2500 VICTOR/TT-801, CL-P10, TS-1 MICRO/SX-8000, HS-80 ONKYO/INTEGRA P-309, INTEGRA M-509 MARK LEVINSON/ML-6AL AUDI-Technica/AT-34E11 ENTRE/EC-30 SME/3012-R SPECIAL TECHNICS/EPC-C100CMK3 FIDELTY RESEARCH/XF-1 SELLESION/DITTON300 KEF/MODEL105.4 KENWOOD/L-08C, L-08M PIONEER/A-980 SANSUI/AU-D907F SONY/TA-AX8 LO-D/TU-1000 LUXMAN/PD300 ADC/ASTRION LINN/ASAK/ S56.4.15 issued. The photograph is a sample, so the actual product may be broken, or there may be markings etc.
※Shipping service. No. 71 Special Feature = New Wave Speakers Building a New Generation of Quality Audio/Answering the Audio Conundrum You Want to Know the Most Right Now (top) /'84 Best Buy Component by Readers' Vote/ Introducing a Tubular EQ Amplifier from Altphone /Published on 1984.7.15. Published models: JADIS/JP80, JA30, JA200 MARANTZ/CD84 PIONEER/P-D90 YAMAHA/CD2 REVOX/B225 DENNSEN/JC80 ACOUSTAT/TNT120, TNP FOSTEX/GZ2001 BEVERIDGE/SYSTEM 5 INFINITY/RS2A LUXMAN/MB300 PIONEER/A150D AR/AR TURNTABLE SPEX/SDX3000, SDT3000 MICRO/MT500, MT1000L/H AKG/P100 LIMITED The photo is a sample, so the actual item may be broken, have marks, etc.