Maintained! A pure Class A power amplifier featuring a plump, warm tone typical of Luxman. It has both softness and strength, and you can enjoy thick sound quality in the mid to low range. Mono drive with BTL connection is also possible. The exterior is dull. Serial W30811307 (Yonejima Satoshi)
Maintenance information: 2024.11.20 Maintained (dismantling the ATT rotary switch, upper contact cleaning, contact polishing, and oxidation prevention treatment. Soldering fixes for all substrates. DC offset and idle current adjustment)
Accessories: No accessories
Main specifications: stereo output 55 W+55 W (8 ohms) pure A grade operation, mono output, 220 W (balanced input), frequency characteristics, 5 Hz to 300 kHz, direct reading type level indicator, W444 x H211 x D417 mm, 22 kg
※There are cracks in the cabinet, so it is inexpensive. Maintained! A pure Class A power amplifier featuring a plump, warm tone typical of Luxman. It has both softness and strength, and you can enjoy thick sound quality in the mid to low range. Mono drive with BTL connection is also possible. On the exterior, there is a crack in the decorative top plate. Serial W10410447 (Yonejima Satoshi)
Maintenance information: 2024.11.20 Maintained (after disassembling the rotary switch, cleaning and polishing the contacts, and anti-oxidation treatment. Soldering fixes for all substrates. AC cord replacement. DC balance and idle current adjustment)
Accessories: No accessories
Main specifications: stereo output 55 W+55 W (8 ohms) pure A grade operation, mono output, 220 W (balanced input), frequency characteristics, 5 Hz to 300 kHz, direct reading type level indicator, W444 x H211 x D417 mm, 22 kg
Maintained including switch and main volume disassembly and polishing! LUXMAN vintage prime amp from the 60's. Although it is a transistor, it was made in '69, so you can hear the soft, rich sound unique to LUXMAN. The design unique to vintage is a masterpiece that is attractive enough as an interior decoration. The exterior has scratches on the top plate and scratches on the upper front. Serial 10214251 (Fujisawa Yukishi)
Maintenance information: 2024.11.20 Maintained (switch disassembly contact polishing. Main volume disassembly contact polishing. I/O pin jack and other polish. The transistors inside the circuit have been replaced. The condenser has been replaced with a high quality one. Sound output operation check)
Accessories: No accessories
Main specifications: continuous output 17W+17W W373 x H125 x D227 mm 4.9 kg
An insulator and magnetic flux tube are passed through the center of the terminator conductor through the 3.0 m speaker cable terminal to prevent the effects of signals due to disturbances in the magnetic field. A character with a thick sound and a sense of vibrancy. You can enjoy using it. The exterior is sticky to the sheath, and there is a feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.9.29 continuity confirmed
Accessories: none
DALI's popular tall boy model. The high quality real wood finish exudes a sense of luxury. It features a mild, high-grade tone with a high texture, and demonstrates its strengths in acoustic sounds and female vocals. There are small scratches on the exterior. Serial 9541018 (Yonejima Satoshi)
Maintenance information: 2024.11.19 sweep test good
Accessories: saran net, spikes, jumper cables (general-purpose products)
Main specifications: 3-way 3 speakers, frequency characteristics, 43 Hz to 25 kHz, crossover, 3.4 kHz, sound pressure level, 90 dB, impedance, 4 ohms, W170 x H845 x D220 mm, 11.7 kg
The price has been drastically reduced! 2024/11/16 sale price 298,000 yen This is a special edition model with further improved quality of the L-509f. The color was changed to blaster white, and the sound quality also changed. The thick high-fidelity tone, which can be said to be the prototype of the current LUXMAN, demonstrates all-round appeal. There are scratches and bumps on the exterior. Serial M50711464A (Fujisawa Yukishi)
Maintenance information: 2024.11.16 Operation confirmed
Accessories: instruction manual, power cord, original box
Main specifications: 160W+160W (8Ω) 240W+240W (4Ω) size W467 x H179 x D435 mm weight 28.5 kg
The price has been reduced. 2024/11/18 sales price 498,000 yen Luxman high-grade SACD player. In addition to the powerful sound with a thick back, this is a versatile machine typical of a modern aircraft, with a high level of freshness and a good signal-to-noise ratio. Not to mention the high level of spatial expression unique to SACD, unlike Luckstone in the past, it is popular with jazz and rock fans for its high instantaneous sound quality. There is a dull feeling of use, but there are no noticeable scratches (Sasaki Shota)
Maintenance information: 2024.11.18 Operation confirmed
Accessories: remote control, manual, power cable
Main specifications: analog output RCA x 1 XLR x 1 digital output (44.1 kHz CD/CD layer only) coaxial x 1 optical (TOS-LINK) x 1 digital input (32/44.1/48/88.2/96 kHz compatible) coaxial x 1 optical (TOS-LINK) x 2 W440 x H153 x D400 mm 23 kg
A popular model that plays a central role in the Lux Primain. The high-quality, soft, and comfortable sound unique to Luxe from the 90s onwards makes listening even when you listen for a long time without getting tired. Furthermore, it has a very rich input system, and since pre/power can be separated, it is excellent in terms of development. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.11.17 Operation confirmed
Accessories: remote control, instruction manual, power cord
Main specifications: 100W+100W, power consumption, 220W, line input, 4 tape systems, balance input, PHONO (MM/MC) input included, W467 x H179 x D440 mm, 21 kg
Maintained! This is an original full range AXIOM 80 with WEMBLEY MIDDX engraving. That sound of standing up is the ultimate in transparency. The high sound pressure that quickly rises from the mid to high range is evident from the source to the completion of the player. The exterior has scratches and a feeling of use over time. *The shape of the magnetic cover is slightly different on the left and right. Serial 2327 2327 (Tomonori Asaine)
Maintenance information: 2024.11.17 Maintained (disassembling all parts, forming deformation and distortion of parts, maintenance, forming of damper edge blades, cone flatness adjustment, slit, rust removal center, yoke, rust removal, slit cleaning, rust prevention centering adjustment, assembly, centering adjustment of each part, and confirming operation)
Accessories: none
Main specifications: Cone type full range unit, 25 cm aperture input, 12 W impedance, 15 ohms, minimum resonance frequency, 20 Hz, playback frequency band, 20 to 20,000 Hz, pore magnetic flux density, 17,000 gauss, voice coil, aperture 2.5 cm
The price has been reduced! 2024/11/9 Denon luxury analog player with sales price of 79,800 yen. The shades and coatings of the cabinets are also impressive. The drive motor is powerful, and the stopping action is instantaneous in a blink of an eye until it rotates at a fixed speed. Record playback with excellent stability and high freshness is attractive. Externally, there are threads and scratches on the dust cover. Serial 3096300425 (Yonejima Satoshi)
Maintenance information: 2024.11.9 operation confirmed
Accessories: power cord, connection cord
Main specifications: quartz lock type direct drive 33/45 rotation static balance S-shaped pipe arm height adjustment range approx. 6 mm needle pressure adjustment range 0 to 4.0 g (1 scale 0.25 g) compatible cartridge weight 14.0 to 20.0 g (headshell included) W490 x H178 x D400 mm 13.6 kg
The price has been drastically reduced! 2024/11/11 sales price 188,000 yen A famous machine that made the CHORD brand name known to the world due to its good sound quality. The fresh sound, which seems to have the advantages of analog and digital, easily covers all music genres. The characters with high musicality and good sound are still attractive enough. The luxurious brilliant design is also attractive. The exterior has a feeling of use such as dullness. Serial 10792 (Tomoho Asaine)
Maintenance information: 2024.11.11 Operation confirmed
Accessories: instruction manual copy power cable (general purpose)
Main specifications: digital input BNC terminal x 2 AES terminal x 1 Toslink terminal x 1 analog output RCA/XLR compatible sample rate 32 to 96 kHz, 176.4/192 kHz (AES dual data mode) buffer switch equipped (short/long) W335 x H65 x D153 mm 4 kg
The price has been drastically reduced! 2024/11/11 sales price 218,000 yen Luxman's highest peak headphone amplifier uses the latest version 4.0 of ODNF, a unique high sound quality amplification feedback circuit, and it is possible to smoothly adjust the volume with little sound quality deterioration using the electronically controlled attenuator LECUA. It is a headphone amplifier that is particular about sound quality, such as using gradation cast iron legs that block unnecessary external vibrations. The exterior is dull and dents can be seen on the top plate. Serial M90600416 (Fujisawa Yukishi)
Maintenance information: 2024.11.11 Operation confirmed
Accessories: instruction manual, power cord
Main specifications: headphone amplifier continuous effective output: unbalanced 4W+4W (8Ω) 2W+2W (16Ω) 1W+1W (32Ω) balance 8W+8W (16Ω) 4W+4W (32Ω) input: unbalanced 1 system/balanced 2 system output: 1 4P/XLR balance system, 1 3P/XLR balance system, 1 standard jack system, 1 through output system W440 x H92 x D400 mm weight 13.3 kg
A wood case compatible with Luxman vacuum tube harmonizer kits, vacuum tube hybrid premain amplifiers, mk2, and vacuum tube FM tuners sold as an ONTOMO MOOK appendix. Made of black walnut, the insulator is made of aluminum. Good condition (Murakoshi Yoichi)
Accessories: instruction manual
Main specifications: W197 x H96 x D97 mm 200g
This is a product that has undergone thorough maintenance, such as 50 CA10 pairs, 10 capacitors replaced, and the entire volume and lever switch dismantled and polished! Please experience not only the sound, but also the impressive volume and feel of the switch. The final model in the LUX38 series, a rare model limited to 300 units. This is the last work of Uehara Susumu, who has consistently designed the 38 series until then, and is characterized by a sense of luxury and a soft, enveloping atmosphere. There are traces of cabinet repairs, but overall it is a beautiful individual (Oikawa Tetsuji)
Maintenance information: 2024.11.13 Maintained (vacuum tube, vacuum tube socket, fuse, semi-fixed resistor, deteriorated electrolytic capacitor, tantalum capacitor, LED, spark killer, resistor replacement. All switches and volumes were completely disassembled and cleaned. Input/output waveform confirmation, rated output test (1kHz sine wave, 8Ω load: 25W+25W, OK), sound output test)
Accessories: none
Main specifications: 30W+30W (8Ω) W490 x H202 x D350 mm 24 kg
Internal and external maintenance has been completed in 2020, such as replacing the coupling condenser with an oil condenser, replacing the banana-compatible SP terminal, and replacing the vacuum tube (50CA10)! This model is based on the concept of making sounds even more straightforward than the MQ60. The warmth of the tone and the indescribable luster sound are truly lackstones. The exterior is scratched on the hood and transformer cover, and paint is peeling. Serial 4810364 (Fujisawa Yukishi)
Maintenance information: 2020.8.25 maintained (50CA10 x 3, 12BH7 x 1, coupling capacitor, electrolytic capacitor, rectifier diode, semi-fixed resistor, RCA terminal, SP terminal, MT tube socket, fuse replacement. Gain VOL, impedance switching SW disassembly contact refinement, oxidation and sulfidation prevention grease coating circuit readjusted, input/output waveform confirmed, rated output tested)
Accessories: No accessories
Main specifications: used vacuum tube 50C-A10 x 4 12BH7A x 2 6267 x 1 EF86EH x 1 output 25+25W (4/8/16 ohm switch switching) speaker output 1 system W410 x H160 x D205 mm 13.8 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/9/22 sales price 148,000 yen All switches have been disassembled and maintained, such as contact polishing! Comes with a cabinet. A preamp kit based on LUXMAN's CL32 tube control amplifier. It is designed so that the distortion ratio can be kept low. The fact that it has been made thin and stylish is also eye-catching. On the exterior, scratches are conspicuous on the VOL. Serial 006141 (Tamura Eiji)
Maintenance information: 2024.9.22 Maintained (all switch disassembly contacts polished contact grease applied. Volume disassembly operation contact polishing and cleaning. Replace the power inlet with a 3P terminal and replace the AC cord. Vacuum tube socket contact check. Capacitor check (maintenance replaced) each input/output operation check) 2021.10.12 manufacturer maintained (lead wire solder deterioration correction, volume base. Phono equalizer wrap ring capacitor defective replacement. Replace all other coupling capacitors that have deteriorated. (Other checks OK, some contacts cleaned)
Accessories: power cable
Main specifications: Phono 2 system W480 x H115 x D325 mm weight 7.0 kg
The price has been reduced! 2024/10/13 sales price 20,000 yen Arm base that can be used with PD-171AL. The arm can mount an Ortofon AS-212D AS-212S. Heavy arm base with chrome plated spin finish on 20mm thick brass. If you're thinking about replacing an arm, don't miss it! There are no noticeable scratches on the exterior (Yamato Yuki)
Accessories: original box instruction manual wrench screw
Main specifications: brass, chrome plated, spin finish, diameter 105 x height 20 mm, weight: 1,105 g
The price has been reduced. 2024/10/6 sales price 89,800 yen ※The top plate is damaged, so it's cheap. The ultimate version of the P-1. Pure A grade specification, which is rare for a headphone amplifier, so you can enjoy detailed and clear sound. There are scratches and stains on the top plate (Sasaki Shota)
Maintenance information: 2024.10.6 operation confirmed
Accessories: power cable, manual
Main specifications: 2W+2W (8Ω) 1W+1W (16Ω) high sound quality feedback circuit “ODNF3.0A”, 2 headphone outputs, 1 RCA/XLR input each, W440 x H82 x D408 mm 8.3 kg
Overhauled product including capacitors and transistors! This is an attractive mid-range model in the D series with lots of exciting sounds and thick sounds. It's a different character from modern amplifiers. When paired with speakers such as JBL, you can enjoy vibrant, deep tones. The exterior is in a state where there is a feeling of use such as dullness over time. Serial 219050594 (Yamato Yuki)
Maintenance information: 2024.11.3 maintained (input/output waveform check, load test (1kHz sine wave, 8Ω load: 90W+90W, OK), sound output test) (electrolytic capacitor, mica capacitor, semi-fixed resistor, transistor, relay, SP and RCA terminals, block capacitor replacement, all SW/VR types are completely disassembled, cleaned, and coated with anti-oxidation sulfide grease, after removing old solder from each board, re-solder, flux removal idol, Offset adjustment, interior/exterior cleaning, heat dissipation sheet replacement, various measurements, audio output tests)
Accessories: none
Main specifications: 90W+90W (8Ω) phono 2 systems (MM/MC switching, MM) line input 2 systems, tape system, 2 systems, pre/power separable, W430 x H168 x D428 mm 20.6 kg
Thorough maintenance was carried out, such as replacing capacitors and deteriorated parts! A custom model whose circuit was changed from the original to a non-feedback amplifier. The output drops by 5W+5W compared to the MQ60, but surprisingly, this one has a better amount of noise, and the sound quality is clean. The appeal is that it is easy to grasp the sense of localization. The exterior has a feeling of use such as dullness. Serial 40401535 (Tomonori Asaine)
Maintenance information: 2024.10.27 Maintained (vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, semi-fixed VR, fuse, spark killer, diode, micro SW replacement. Load test, input/output waveform confirmation impedance switching SW/gain VOL decomposition contact refinement, application of anti-oxidation/sulfidation grease, input/output waveform confirmation, load test (1kHz sine wave, at 8Ω load: 25W+25W), sound output test)
Accessories: none
Main specifications: 50CA10 push-pull output 25W+25W (4/8/16Ω) 50CA10 x 4/12BH7A x 2/6267 W410 x H160 x D205 mm weight 14 kg
Power transformer primary: 100-117V secondary: 12.6V/1A, 6.3V/2A x 2, 40V/50mA, -10-0-10-130-150V/DC180mA ((VOLTAGE DOUBLER) /AC0.6A (CONTINUOUS)) W100 x H75 x D85 mm approx. 3.4 kg (actual measurement, not including protrusions) There is a lot of floating on the cover rust part (Kojima Yosuke)
Accessories: none
Comes with casters. Hayami's 5-tier horizontal audio rack with 3 additional tiers of GT-9731. A style that sticks to standards and is faithful to the basics. The design combines functionality with a sense of luxury. The exterior is damaged, stained, and smudged, and has many signs of use. There is glitch due to damage to the dowels on the side plate and partition board, missing dowels, etc. (TAKIMOTO Yutaka)
Accessories: none
Main specifications: W1724 x H1300 x D580 mm approx. 169 kg
The disposal price has been reduced. Member prices are not applicable. 2022.12.5 sales price 39,800 yen Arm base for the company's tone arms MH-104S and MH-124S. Machined stainless steel has a sense of luxury (Sasaki Shota)
Accessories: none
Main specifications: 24mmφbase, machined stainless steel, 340 g, mounting board hole, φ25 mm, mounting board thickness ~ 20 mm
The price has been reduced! 2024/9/1 sales price 59,800 yen Maintained. An eye-catching Lax pre-main amplifier with a unique indicator. It is a traditional lackstone, and the soft and warm mid-low range like a vacuum tube is attractive. The speakers, which have a solid sound quality, also play softly. There is a slight gap in the scale on the BASS dial. The exterior has rolled up veneer, scratches, and dullness. Serial 11401165 (Yonejima Satoshi)
Maintenance information: 2024.9.1 Maintained (12 road deteriorated transistors and 18 capacitors replaced. Disassemble the switches and polish the contacts and apply contact cleaner. Main volume disassembly contact polishing. I/O pin jack polish. (Deterioration has been seen on the speaker terminals, and the plastic is discolored and scraped, but there is no problem with operation)
Accessories: No accessories
Main specifications: 40W+40W (8Ω) W443 × H153 × D273 mm 9.3 kg
USB cable 1.5m USB-A/B type transmission line has the same respective core structure to minimize phase shift in the high frequency region. Uses core wire taping with Japanese paper, which has an antistatic effect. It's a soft sound with a moderate sense of localization (Kojima Yosuke)
Accessories: none
The disposal price has been reduced! (Member discounts are not applicable) 2024/8/25 sales price 15,000 yen 38cm cone type woofer only 1 uses Alnico magnets for the magnetic circuit. 200Ω high impedance type, reproduces sticky low frequencies. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.8.25 sound output confirmed
Accessories: none
Main specifications: playback frequency band 30Hz to 1.5kHz sound pressure level 106dB input 35W impedance 200Ω, total magnetic flux 435,000 maxwell weight 13.5 kg
L-507 wood cabinet If you are looking for one, why don't you do it (Daiki Goto)
Accessories: none
Main specifications: W450 x H160 x D268 mm, weight 2.1 kg (actual measurement)
Output transparent sale push pull output 35W primary: 8kΩ secondary: 4-8-16Ω usage: 7189 app, etc. W82 x H72 x D82 mm approx. 1.6 kg/piece (actual measurement, not including protrusions) The plate is often scratched, printing is erased a lot, and there are paint floats due to rust in places (Kojima Yosuke)
Accessories: none
The price has been drastically reduced. 2021/9/22 sales price 99,800 yen This is Hayami's horizontal audio 5-tier rack with 3 tiers added to the GT-9731. A style that is faithful to the basics with a focus on standards. It is a design that combines functionality with a sense of luxury. The exterior has a lot of damage, dirt, stains, etc., and there is a feeling of use. There is sagging due to damage to the dowels on the side plates and partition boards, missing dowels, etc. (TAKIMOTO Yutaka)
Accessories: None ※3 lower shelves are missing
Main specifications: W1724 x H1380 x D580 mm approx. 185 kg
The price has been drastically reduced. 2021/9/21 sales price 99,800 yen with casters. This is Hayami's horizontal 5-tier audio rack with 3 tiers added to the GT-9731. A style that is faithful to the basics with a focus on standards. It is a design that combines functionality with a sense of luxury. The exterior has a lot of damage, dirt, stains, etc., and there is a feeling of use. There is sagging due to damage to the dowels on the side plates and partition boards, missing dowels, etc. (TAKIMOTO Yutaka)
Accessories: with KP-4CT casters (set of 2)
Main specifications: W1724 x H1300 x D580 mm approx. 169 kg
Power transformer used in MQ60 vacuum tube amplifiers Primary: 100V Secondary: 360V/280mA 100V/350mA 60V/70mA CT-6.3 V/2A W104 × H97 x D87 mm approx. 4.3 kg (actual measurement, not including protrusions) (Yosuke Kojima)
※Shipping service. No. 58 Special Feature = 3rd “THE STATE OF THE ART: Supreme Component” Award Selection/New JBL 4345 Detailed Report/EMT927 vs. Torrance Reference/Listen to the Tannoy SRM Series/Infinity “IRS” Anatomy/1981.4.15 issued. Posted models: JBL/4345BWX MCINTOSH/MC2500 VICTOR/TT-801, CL-P10, TS-1 MICRO/SX-8000, HS-80 ONKYO/INTEGRA P-309, INTEGRA M-509 MARK LEVINSON/ML-6AL AUDI-Technica/AT-34E11 ENTRE/EC-30 SME/3012-R SPECIAL TECHNICS/EPC-C100CMK3 FIDELTY RESEARCH/XF-1 SELLESION/DITTON300 KEF/MODEL105.4 KENWOOD/L-08C, L-08M PIONEER/A-980 SANSUI/AU-D907F SONY/TA-AX8 LO-D/TU-1000 LUXMAN/PD300 ADC/ASTRION LINN/ASAK/ S56.4.15 issued. The photograph is a sample, so the actual product may be broken, or there may be markings etc.
※Shipping service. No. 71 Special Feature = New Wave Speakers Building a New Generation of Quality Audio/Answering the Audio Conundrum You Want to Know the Most Right Now (top) /'84 Best Buy Component by Readers' Vote/ Introducing a Tubular EQ Amplifier from Altphone /Published on 1984.7.15. Published models: JADIS/JP80, JA30, JA200 MARANTZ/CD84 PIONEER/P-D90 YAMAHA/CD2 REVOX/B225 DENNSEN/JC80 ACOUSTAT/TNT120, TNP FOSTEX/GZ2001 BEVERIDGE/SYSTEM 5 INFINITY/RS2A LUXMAN/MB300 PIONEER/A150D AR/AR TURNTABLE SPEX/SDX3000, SDT3000 MICRO/MT500, MT1000L/H AKG/P100 LIMITED The photo is a sample, so the actual item may be broken, have marks, etc.
The 1.5m PSE standard power cable is sharp, but the increase in S/N speed is not deliberate and I like it. When I held it, it was heavy and had a sense of luxury. There was rubbing and dirt around the plug (Kojima Yosuke)
Accessories: none