Ethos (Ethos), limited to 500 pieces worldwide, is now in stock! SPU Ethos was born as the culmination of an unchanging spirit that has been passed down for over 60 years, refined with the latest technology. The classic SPU sound shines even more, captivating analog fans. The exterior is generally good. Serial 037430 (Murakoshi Yoichi)
Maintenance information: 2024.6.18 sound output confirmed
Accessories: original box, instruction manual, needle cover
Main specifications: Output voltage (1 kHz 5 cm/sec): 0.3 mV channel balance (1 kHz) 1.0 dB channel separation (1 kHz) 20 dB channel separation (15 kHz) 10 dB frequency characteristics (20 Hz-25,000 Hz) ± 2 dB tracking ability (315 Hz, 70 μm under proper needle pressure Horizontal compliance: 8 μm/Mn stylus type Nude Elliptical Stylus Tip Radius: r/R 8/18μm Cantilever Material Aluminum Suitable Needle Pressure: 4.0g Needle Pressure Range: 3.0-5.0 g Tracking Angle 20° Internal Impedance 3.5Ω Recommended Load Impedance 10Ω or More Coil Wire 8N High Purity Copper Cartridge Shell Wood Powder and Resin Composite Material Dead Weight 32g
The long arm model with Amtrans arm base is now in stock for the first time! The arm base is SME type. Pure straight FIDELIX tone arm with hard stainless steel and gemstone bearings. The product name is “0 sideForce” because the arm always moves horizontally to balance even when side force is generated, so no canceller is required and the side force becomes 0. It is in good condition with no noticeable scratches. (FUJISAWA KOSHI)
Maintenance information: 2024.6.25 continuity confirmed
Accessories: instruction manual, arm cable, screws, shell, cleaner, subway
Main specifications: distance between hard stainless steel (SUS304) turntable and center of arm 299 mm ± 4 mm distance between arm fulcrum and needle point 281 mm underhang 18 mm mounting hole φ30 mm compatible cartridge to 28.5 g (compatible up to 35.5 g when using a sub-weight)
The long arm model with Amtrans arm base is now in stock for the first time! The arm base is SME type. Pure straight FIDELIX tone arm with hard stainless steel and gemstone bearings. The product name is “0 sideForce” because the arm always moves horizontally to balance even when side force is generated, so no canceller is required and the side force becomes 0. It is in good condition with no noticeable scratches. (FUJISAWA KOSHI)
Maintenance information: 2024.6.25 continuity confirmed
Accessories: instruction manual, arm cable, screws, shell, cleaner, subway
Main specifications: distance between hard stainless steel (SUS304) turntable and center of arm 299 mm ± 4 mm distance between arm fulcrum and needle point 281 mm underhang 18 mm mounting hole φ30 mm compatible cartridge to 28.5 g (compatible up to 35.5 g when using a sub-weight)
An audio board with a ball point contact structure. The high damping effect of point contact quickly dampens equipment vibrations. Furthermore, it has an excellent seismic isolation effect against shaking from 360 degrees in the horizontal direction. You can see a feeling of use, such as appearance, dullness, marks, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: Effective space: W590 x D490 mm Load capacity: approx. 250 kg W650 x H44 x D550 mm 14.5 kg
An audio board with a ball point contact structure. The high damping effect of point contact quickly dampens equipment vibrations. Furthermore, it has an excellent seismic isolation effect against shaking from 360 degrees in the horizontal direction. You can see a feeling of use, such as appearance, dullness, marks, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: Effective space: W590 x D490 mm Load capacity: approx. 250 kg W650 x H44 x D550 mm 14.5 kg
An audio board with a ball point contact structure. The high damping effect of point contact quickly dampens equipment vibrations. Furthermore, it has an excellent seismic isolation effect against shaking from 360 degrees in the horizontal direction. A feeling of use can be seen on the exterior, peeling of the veneer, dullness, marks, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: Effective space: W590 x D490 mm Load capacity: approx. 250 kg W650 x H44 x D550 mm 14.5 kg
The price has been reduced! 2024/4/28 sales price 5,000 yen set of 4 speaker stands Block type can be installed either vertically or horizontally. It is a very convenient and useful item for installing medium sized speakers, etc. There is a feeling of use on the exterior, such as dullness or peeling of the outer sticker ※ There is content like sand inside (Asaine Tomoho)
Accessories: none
Main specifications: Scythe W110 x H190 x D390 mm weight 6.6 kg (actual measurement)
※1 bottle only. Shorthorn used in the 43 series. It can also be built into an enclosure, but it makes you hear good sound even when attaching a driver and placing it on top of the enclosure. There are paint peeling and scratches on the exterior (Yonejima Satoshi)
Accessories: No accessories
Main specifications: 80 degrees horizontal orientation for 1-inch drivers, 45 degrees vertical, recommended crossover 1.2 kHz, baffle opening diameter 108 mm, depth 216 mm
※1 bottle only. TOA large metal radial horn. In terms of sound quality, it has a narrower impression than Altec's sectional horn 311, but it has a bright sound with a sense of overhang unique to radial horns. *The diameter of the mounting hole seems to be slightly smaller than ALTEC, so there is a possibility that ALTEC's 1.5-inch drivers will not fit depending on individual differences. Overall, there are wounds, dullness, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: cross 500 Hz or more, horizontal 90 degrees, vertical 40 degrees, throat diameter 35.5 mm, compatible driver HFD-651, width 720 mm, height 220 mm, depth 580 mm, 10.9 kg
※It is cheap because it is in poor condition due to numerous modifications. Heavyweight horizontal audio rack It's sturdy, so it's fine even if you put a super dreadnought analog player on the top plate. The inside is slightly larger, so even slightly larger full-size equipment can be stored. Since there are many modifications such as the exterior, attaching a copper plate to the upper right shelf, attaching a tile mat to the bottom, and attaching a handle to the tray, etc., the shelf on the right side does not come off, and a feeling of use such as dullness and abrasions can be seen (Kobayashi Hitoshi)
Accessories: none
Main specifications: Overall measurement W1200 x H535 x D572 mm inner dimensions on one side (without shelf board) W530 x H430 x D (top plate 560, medium plate 470, lower stage 560) mm top plate thickness 45 mm shelf board thickness 23 mm weight 69.85 kg
The price has been drastically reduced. 2021/9/22 sales price 99,800 yen This is Hayami's horizontal audio 5-tier rack with 3 tiers added to the GT-9731. A style that is faithful to the basics with a focus on standards. It is a design that combines functionality with a sense of luxury. The exterior has a lot of damage, dirt, stains, etc., and there is a feeling of use. There is sagging due to damage to the dowels on the side plates and partition boards, missing dowels, etc. (TAKIMOTO Yutaka)
Accessories: None ※3 lower shelves are missing
Main specifications: W1724 x H1380 x D580 mm approx. 185 kg
The price has been drastically reduced. 2021/9/23 sales price 99,800 yen This is Hayami's horizontal audio 5-tier rack with 3 tiers added to the GT-9731. A style that is faithful to the basics with a focus on standards. It is a design that combines functionality with a sense of luxury. The exterior has a lot of damage, dirt, stains, etc., and there is a feeling of use. There is sagging due to damage to the dowels on the side plates and partition boards, missing dowels, etc. (TAKIMOTO Yutaka)
Accessories: None ※3 lower shelves are missing
Main specifications: W1724 x H1380 x D580 mm approx. 185 kg
The price has been drastically reduced. 2021/9/22 sales price 99,800 yen This is Hayami's horizontal audio 5-tier rack with 3 tiers added to the GT-9731. A style that is faithful to the basics with a focus on standards. It is a design that combines functionality with a sense of luxury. The exterior has a lot of damage, dirt, stains, etc., and there is a feeling of use. There is sagging due to damage to the dowels on the side plates and partition boards, missing dowels, etc. (TAKIMOTO Yutaka)
Accessories: None ※3 lower shelves are missing
Main specifications: W1724 x H1380 x D580 mm approx. 185 kg
The price has been drastically reduced. 2021/9/21 sales price 99,800 yen with casters. This is Hayami's horizontal 5-tier audio rack with 3 tiers added to the GT-9731. A style that is faithful to the basics with a focus on standards. It is a design that combines functionality with a sense of luxury. The exterior has a lot of damage, dirt, stains, etc., and there is a feeling of use. There is sagging due to damage to the dowels on the side plates and partition boards, missing dowels, etc. (TAKIMOTO Yutaka)
Accessories: with KP-4CT casters (set of 2)
Main specifications: W1724 x H1300 x D580 mm approx. 169 kg
Disposal prices have been reduced. The 2020/2/10 sales price is 3,000 yen. ※It is inexpensive because it is in poor condition. Ceiling hanging bracket for the company's speaker 301 MM/2. It can be adjusted up and down by ± 90 degrees, and can be rotated 360 degrees horizontally. The feeling of use, rust, dullness over time, and stains are severe, and there are places with rust. (WATANABE Tadashi)
Accessories: none
Main specifications: W248 x D150 x H195 mm 1.4 kg/piece
Hamilex (Hayami Kosan) pedestal speaker stand. The direction of the top plate can be changed to vertical/horizontal orientation according to the speaker, and the mounting direction of the struts can also be changed according to the atmosphere of the speaker to be installed. (Fujisawa Yukishi)
Accessories: Instruction manual
Main specifications: Total load capacity 50 kg (1 unit) W350 × D320 × H400 mm Approx. 5.8 kg/unit