Sold 1 McIntosh Print Used for drive tubes of the company's MC275CE Made in China (rejection value 50) * Measurements are gm values measured on tv-7 tv-7 (Yosuke Kojima )
Accessories: None
Sold 1 McIntosh Print Used for drive tubes of the company's MC275CE Made in China. Measured value 62 (rejection value 50) * Measurements are gm values measured on tv-7 tv-7 (Yosuke Kojima )
Accessories: None
Disposal prices have been reduced. Member discounts are not applicable. 2021/4/10 sales price 2,000 yen. Remote cable 2.0m A remote cable that can synchronize the power switch between the company's control amplifier 035 and the power amplifier 036. It is connected from DC-OUT of 035 to DC-IN of 036 and works in conjunction with 035 operation. (Kondo Hirotsugu)
Maintenance information: 2021.4.4 Linkage confirmed by the company 035 and 036
Accessories: none
Pair Tube Bi-triode Power Tube Made in USA JAN Measurement Value 60/60 (Rejection Value 40) With Original Box ※ The pair is judged based on GM value measured on the tv-7 test machine (Yosuke Kojima)
Accessories: original box
1 sold bi-triode power tube made in the USA JAN measurement value 58 (rejection value 40) with original box ※ Measured value is gm value measured by tv-7 tester (Yosuke Kojima)
Accessories: original box
Pair Tube Bi-triode Power Tube Made in USA JAN Measurement Value 60/60 (Rejection Value 40) With Original Box ※ The pair is judged based on GM value measured on the tv-7 test machine (Yosuke Kojima)
Accessories: original box
Pair Tube Bi-triode Power Tube Made in USA JAN Measurement Value 60/60 (Rejection Value 40) With Original Box ※ The pair is judged based on GM value measured on the tv-7 test machine (Yosuke Kojima)
Accessories: original box
The price has been reduced. 2021/5/6 sales price 7,000 yen turntable seat for Garrard 301. The condition is not very good, such as slight undulations and wrinkles. (KONDO HIROTSUGU)
Accessories: original case
1 sold in USA JAN tea base measurement 90 (rejection value 48) with original box ※ Measured value is gm value measured with tv-7 test machine (Yosuke Kojima)
Accessories: original box
The price has been drastically reduced. 2021.6.23 sales price 49,800 yen ※Conductivity has been confirmed, but since the terminal has not been treated and the ground wire is broken, it is currently sold. Exclusive tone arm for DECCA MARK 1/2/3 cartridges. Simple structure using straight pipes. Since the needle pressure is a dedicated arm, it is preset and set to an appropriate value. It is designed to maintain an optimal state for the head of the company (Murakoshi Yoichi)
Maintenance Information: 2021.6.13 Continuity Confirmed
Accessories: armrest
Main specifications: static balance type, total length 303 mm, execution length 225 mm
Replacement needle for Toshiba cartridge C-34M It is unchecked for replacement needle only. (Mizushima Itsuro)
Maintenance information: 2021.7.3 unchecked
Accessories: original box
Replacement needles for SANYO (OTTO) components stereo A-352, DC-620X, DC-710, etc. It is unchecked for replacement needle only. (Mizushima Itsuro)
Accessories: case
Unopened Replacement needle for Columbia/Denon cartridge, PU-1270, PU-1280, SPC-310 It is unchecked for replacement needle only. (Hitoshi Kobayashi)
Accessories: case
※Only one cork & brass two-layer insulator. Compact size ideal for mini compo and small speakers. (Ryo Mizusaki)
Accessories: none
Main specifications: 2-layer hybrid construction, load capacity of 5 kg per piece, diameter 18 x 11 mm thick, about 18 g per piece
I cut the price. 2021/8/30 selling price 49,800 yen rare! Decka's Gramophone Rally is Hi-fidou's first arrival. The turntable is smaller than the board, and the sound has a sense of scale in the UK with a compact body. The atmospheric design, retractable needle case and spring handle are very attractive. Unknown details (Yoichi Murakoshi)
Maintenance information: 2021.8.30 sound confirmed
Accessories: replacement needle
Main specifications: W155 × H280 (350 with the lid open) × D375mm 5.5kg
Sound can be produced, but there is uneven rotation and sound cracking, so it will be sold as it is. The volume is not loud, but it has a soft tone that creates a nostalgic atmosphere. The appearance is a stain scratch kusumi of the age. (Takimoto Yutaka)
Maintenance information: 2021.11.27 Operation confirmed
Accessories: handle, paper horn
Main specifications: W278 × H78 × D300mm 3.7kg (actual measurement)
The disposal price was lowered. Member discounts are not applicable. 2021/11/27 Selling price 148,000 yen The product around 1920 features a telescopic tone arm, needle pressure, and volume adjustment possible. 2-spring, oval straight horn The volume is not large, but the tone is delicate and coherent. The rotation is relatively stable, but there is sound cracking, so it is currently sold. The appearance has dirt scratches of age. (Takimoto Yutaka)
Maintenance information: 2021.11.27 operation confirmed
Accessories: handle
Main specifications: W440 × H380 × D520mm 17.9kg (actual measurement)
The winding of the mainspring is smooth and can produce sound, but there is rotation noise, unevenness, and sound shake, so it is sold as it is. The volume is not big, but I feel good in the middle and high range center. The appearance is rust of the age, there are dirt scratches Kusumi. (Takimoto Yutaka)
Maintenance information: 2021.12.1 operation confirmed
Accessories: handle
Main specifications: W358 × H260 × D295 6.85kg (actual measurement)
The winding of the mainspring is smooth and can produce sound, but the platter swells, and there is no screw in the hinge and the lid comes off, so it is sold as it is. The volume is not big, but I feel good in the cohesion of the sound. The appearance is rust of the age, there are dirt scratches Kusumi. (Takimoto Yutaka)
Maintenance information: 2021.12.8 operation confirmed
Accessories: handle
Main specifications: W400 × H335 × D470 11.95kg (actual measurement)
The price has been reduced. 2021/12/19 sales price 1,000 yen. ※There was a sound, but details such as characteristics have not been checked. Dynamic microphone made in China with standard specifications. How about an easy way to use it for a wide range of purposes other than vocals? Total body length 165 cm, 210 g (Murakoshi Yoichi)
Maintenance information: 2021.11.28 sound output confirmed
Accessories: none
※1 bottle only. Maintained! This is a rare blue frame (above) model LX5. The impedance is 8 ohms, and the cross is 500 Hz, so be sure to use a 175 or 375 driver that uses 8 ohms! There are spots, rust spots, and small scratches. (Honda Maki)
Maintenance information: 2021.12.21 Conductivity confirmed 2019.4.4 Maintained (re-fix the internal coil with silicone agent. Remove rust from terminals and mounting screws, clean, and tighten. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: No accessories
Key Specifications: Crossover Frequency: 500 Hz Level Control: 3 Position Switch Input Impedance: 16 ohms 159 x 153 x 120 mm 2.3 kg
KIKUTANI guitar stand Comes with a fall prevention strap. There are some abrasions (Yoichi Murakoshi)
Accessories: none
Main specifications: W510 × H760 (maximum) × D330mm
KIKUTANI guitar stand Comes with a fall prevention strap. There are some abrasions (Yoichi Murakoshi)
Accessories: none
Main specifications: W510 × H760 (maximum) × D330mm
Special Feature = All of the power supplies and accessories that are currently being talked about are full of techniques to demonstrate the power of your equipment! /Power supply maintenance and introduction effect, case report/Research on accessories to bring out better sound/H.23.8.15 issue
Mini plug to stereo standard plug conversion cable It is a model using OFC as a wire rod. (Eiji Tamura)
Maintenance information: 2022.1.5 continuity confirmed
Accessories: original box
TV rack with unknown details. The upper top plate is attached to glass, and there are 2 casters on the back (2 legs in the front), 1 shelf board is about 18 mm thick, and the lower dowel has 3 places at intervals of about 32 mm. There is a feeling of use such as scratches, dents, etc., and the back plate is cut off quite a bit (Takasaki Atsushi)
Accessories: 1 shelf
Main specifications: Outer dimensions approx. W800 × H500 (450 excluding casters and legs) × D400 (upper top plate 355) mm Upper inner dimensions approx. W750 × H130mm Lower inner dimensions approx. W750 × H255 mm Approx. 25 kg
The disposal price has been reduced! (Member discounts are not applicable) 2022/2/5 sales price 2,000 yen ※1 bottle only. The speaker stand compatible with BOSE's various surround speakers is compatible with the 3,2,1 series, AMS-series, AM series, FreeStyle, and LS series. The exterior is dull and has a feeling of use. (ASAINE Tomonori)
Accessories: none
Main specifications: W177 x H968 x D254 mm 3.1 kg
* I checked the sound, but since it is cheap, it will be passed on as it is. 3-way speaker The saran net on both sides does not open, the screws on the back plate are rusted, and the contents are unidentified because they cannot be removed. There are scratches, dirt, and dullness on the exterior (Katsuji Hiura)
Maintenance information: 2022.1.27 sound output check OK
Accessories: Saran net
Main specifications: 8Ω 60W playback frequency band 35-20,000 Hz W360xH790×D290mm 13.25kg
An enclosure that seems to be for Sansui's old system component speakers. The lattice box with legs reminiscent of JBL's Baron and Bicount is really fashionable. The lattice on both the left and right is out of the frame. There are traces of internal remodeling (Fujisawa Koshi)
Accessories: None
Main specifications: opening diameter 212mm (screw pitch 240mm), aperture diameter 110mm (countertop 170mm, screw pitch 140mm), opening diameter 95mm (for bass reflex port/wood screw pitch 118mm), aperture diameter 70mm (Countertop 92mm, Screw Pitch 104mm) 14mm Particle Board, Veneer Finish W500 × H665 × D430mm 15kg
The price has been drastically reduced! 2022/5/1 selling price 79,800 yen It is a masterpiece 505J of domestic enclosure. With enough contents and box noise, it is a highly recommended box for those who use JBL. The excellent design unique to vintage is also attractive as an interior. The appearance has damage such as corner chips and abrasions. * The hakama has been removed, and there are no conversion baffles or mechanical plates. (Satoshi Yonejima)
Accessories: lattice net
Main specifications: W475 × H705 × D395 mm approx. 23 kg/book (actual measurement)
The price has been reduced. 2022/7/4 sales price 12,000 yen 2.5mm plug specification for genuine balance cable for IER-Z1R. Shafts have been exchanged with perfect accuracy. If you have an DAP with a 2.5 mm balance terminal such as Astell&Kern, this is for you. (SASAKI Shota)
Maintenance information: 2022.7.4 sound output confirmed
Accessories: none
The disposal price has been reduced! Member prices are not applicable. 2022/7/16 selling price 100,000 yen wooden 46cm double woofer type. Baffle opening diameter 425mm Screw pitch 490mm Baffle and enclosure plate thickness 24mm Duct opening diameter 108mm Both the front and back plates cannot be removed. There is a difference in discoloration on the left and right in appearance, and there are corner chips, digging scratches, and dirt stains. (Yutaka Takimoto)
Accessories: none
Main specifications: W1600 × H950 × D850 mm (actual measurement) The weight has not been measured, but it seems that it is 100 kg or more.
Pair Tube 45Special/38142 Compatible Ball Fishing Rod Type Filament Measurement Value 98/92 (Rejection Value 55) Geta Burns, is a bargain because it has decreased ※The pair is GM measured with the tester TV-7 Judgment is based on the value (Yosuke Kojima)
Accessories: none