※Surface deterioration is noticeable, so it is inexpensive. The die-cast aluminum shell has no screws, has a heavy weight, is sturdy, and the design is stylish and creative. The rigidity is high and low frequency tightness can be expected. The exterior has oxidation and dullness on the metal surface (Satoshi Yonejima)
Maintenance information: 2024.6.30 continuity confirmed
Accessories: No accessories
Main specifications: Die-cast aluminum, self-weight 10.6 g
*The volume cannot be replaced with a replacement product, and the volume cannot be changed with the remote control. Maintained! A mid-range model in the ES series, a masterpiece amplifier from the heyday of audio. While the sound is crisp and well-contoured, the balance that doesn't feel tight is appealing. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.30 maintenance completed (speaker relay replacement, 16 other resistance deterioration locations replaced, other mute SW, source direct SW, INPUT selector, direct SW, Cartrich LOAD, RECOUT, SW disassembly contact polishing cleaning grease application, A board B board solder poor contact repair, DC bias DC balance adjustment, DC bias DC balance adjustment, volume VR 9 o'clock position replacement for Gari Then the volume cannot be changed. (The current situation is limited due to the weight of BAL and Tone volumes, grease injection treatment for shafts, etc., and no parts and cannot be replaced)
Accessories: remote control, instruction manual
Main specifications: 105W+105W (8Ω) W470 × H165 × D435 mm 21.2 kg
High compliance MC cartridges It boasts a wide range playback capability of 60 kHz, and its sharp, energetic sound is suitable for jazz rock. The sound quality is bright and crisp with good low frequency resolution. The exterior is dull (Jun Tamai)
Maintenance information: 2024.6.30 sound output confirmed
Accessories: needle cover
Main specifications: solid diamond special elliptical needle playback frequency range 20 Hz to 60 kHz voltage 0.4 mV impedance 33 Ω needle tip 0.07 x 0.14 mm square needle pressure 1.4 g dead weight 6 g
Set of 4 Block shape with R processing on one side of the front. The outside of the speaker fits both R-type and square-shaped types. It has a sturdy design and natural sound quality that brings out the goodness of wood. The exterior has small scratches and a feeling of use (Hiroki Aso)
Accessories: none
Main specifications: W90 x H180 x D320 mm 3.5 kg/bottle
*Currently sold. The final model of the DENON step-up transformer using all LC-OFC lines. Small and affordable, yet clear sound with high S/N. It is a versatile type that is compatible with various cartridges from 3 to 40 ohms. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.6.30 Operation confirmed
Accessories: none
Main specifications: All LC-OFC lines used, LR independent permalloy double shield compatible cartridge impedance, 3 to 40 ohms, boost ratio 1:10, connection cord, 40 mm, frequency characteristics, 20 Hz to 50 kHz, W50 x H37 x D110 mm, 260 g
※The broken frame of the saran net is being repaired. The top model of the company's 30th anniversary model SCM50! This is a luxurious product that uses high quality parts not used in standard models, such as a coil using pure silver wire for the interior and pure silver plating for the speaker terminal. The exterior is faded on the front, and there are small scratches on the top plate. There is a noticeable blow to the back (Oikawa Tetsuji)
Maintenance information: 2024.6.30 sweep test, operation confirmed
Accessories: instruction manual, spike, spike base, jumper plate
Main specifications: 3-way 3-speaker bass reflex type 88dB 8Ω W400 x H1163 x D500 mm 66.4 kg
The price has been reduced! 2024/6/27 sales price 79,800 yen A shell oval needle features the original direct sound of the SPU. The sharp, firm, and powerful mid-low range and detailed expressiveness are attractive. There are fewer incidental sounds than the G-shell elliptical type, so you can enjoy an even more direct tone. The needle cover is partially chipped. Serial 412790 (Tamura Eiji)
Maintenance information: 2024.6.27 Operation confirmed
Accessories: needle cover
Main specifications: MC type 0.2 mV 3 to 4.5 g internal impedance 2 ohms load resistance 47 kΩ oval needle dead weight 23.6 g (mounter and screws included)
The price has been reduced. 2024/6/26 sales price 79,800 yen DALI's popular tall boy model. The high quality real wood finish exudes a sense of luxury. It features a mild, high-grade tone with a high texture, and demonstrates its strengths in acoustic sounds and female vocals. Exterior, the saran net is extremely hard to attach and detach, so there are cracks in the dowel hole in one place, and a feeling of use such as dullness, abrasions, etc. can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.6.26 Operation confirmed
Accessories: instruction manual, saran net, jumper, spike, spike holder
Main specifications: 3 way 3 speakers, frequency characteristics, 43 Hz to 25 kHz, crossover, 3.4 kHz, sound pressure level, 90 dB, impedance, 4 ohms, W170 x H845 x D220 mm, 11.7 kg
The price has been reduced. 2024/6/26 sales price 12,800 yen It's a high range with a wide range, and a low to medium range with a sense of volume that you wouldn't think of it as a compact speaker. The speaker has a simple design and is easy to match with the interior. There are small scratches, dullness, etc. on the exterior (Asaine Tomoho)
Maintenance information: 2024.6.27 Operation confirmed (good sweep test)
Accessories: saran net
Main specifications: impedance 6 ohms maximum allowable input: 80 W (JEITA) 120 W (PEAK) frequency band 45 Hz to 60 kHz crossover frequency 2 kHz 6 Ω size W180 x H270 x D165 weight 3.7 kg
Fully maintained! 2-way floor speaker with a double woofer and 1 horn. With the benefit of the 2234H woofer, which has a fast response and is highly efficient, I have the impression that it is very easy to sound even though it is a double woofer. Coupled with the excellent penetration of the biladial horn, it plays a thick, and exciting JBL sound in the mid to low range. The finish is beautiful due to exterior maintenance, but there are some paint unevenness and scratches on the corners. Serial 255942/252374 (Yonejima Satoshi)
Maintenance information: 2024.5.27 maintained (exterior repair/polishing/oil finish front and rear baffle/hakama/horn coating, saran net replacement driver maintenance: magnetic circuit gap cleaning/center adjustment, sound absorbing material replacement, terminal cleaning/screw replacement network maintenance: frequency characteristic check, ATT/switching SW cleaning, terminal cleaning/screw replacement unit detachment)
Accessories: saran net
Main specifications: 2 way 3 speaker bass reflex type [unit used] 38cm woofer/2234H x 2 driver/2421A+ biladial horn/2344 frequency characteristics 30Hz-16kHz impedance 8Ω sound pressure level 96dB allowable input 375W crossover frequency 1,000 Hz (30Hz to 1kHz on one side, 100Hz or less on the other) Dimensions W965 x H908 × D515mm weight 114 kg/1 bottle
The price has been reduced! 2024/5/14 sales price 1,000 yen*Currently sold. Details of only one Sony 15 cm full range unit are unknown, but there is an I-502-437-11 description on the back. I was able to sweep and make a sound. The exterior has dullness, stains, etc. (Tomoho Asaine)
Maintenance information: 2024.5.14 sound output confirmed
Accessories: none
Maintained! This is a limited edition model that appeared as a gold version of the CD-94. The sound that can be heard by the combination of the CDM-1 mechanism and the TDA1541 multi-bit DAC makes me feel the high level of analog-like musicality while having a diverse amount of information. The exterior is in a state where there are many signs of use, such as dullness and scratches over time. Serial MZ02722110037 (Yamato Yuki)
Maintenance information: 2024.6.13 maintained (tray slide motor belt, CD standby motor belt replacement, bypass C replacement in other servo boards, operation check)
Accessories: none
Main specifications: 1 analog output, 1 digital output, 1 optical and coaxial systems, dimensions W462 x H104 x D355 mm, weight 12 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/1 sales price 298,000 yen Interior and exterior refreshment maintenance has been completed and brushed up! A consumer model of the 2S-305, a timeless monitor speaker masterpiece that Japan is proud of. The thick and clear midrange and detailed high frequencies, which cannot be felt with the look, vividly reproduce vocals. The sound that accurately expresses the characteristics of an amplifier that is set regardless of whether it is a vacuum tube or transistor makes me feel the goodness of the device I have on hand that I haven't been able to see until now. The exterior is in perfect condition due to maintenance. Serial 351364 4851370 (Yamato Yuki)
Maintenance information: 2023.12.1 Maintained (exterior polishing, oil finish, exterior repair, front and rear baffle painting to create missing parts, saran net replacement, velcro replacement. Woofer maintenance center adjustment, edge damping agent application, disconnection solder treatment, center cap dent correction. Tweeter maintenance center cap internal cleaning and replacement, center adjustment, corn paper edge crack repair, edge damping agent application, unit detachment. Network maintenance frequency characteristics check, ATT contact cleaning, terminal cleaning sound operation confirmed)
Accessories: saran net
Main specifications: 2 way bass reflex system input impedance 8 ohms output sound thickness level 96 dB crossover frequency 1500 Hz W650 × H880 × D445 mm weight 50 kg
The price has been drastically reduced. 2024/6/19 sales price 298,000 yen Maintenance completed! Genuine Electric AC 100V specification with cabinet The Macintosh 7000 series stereo power amplifier was announced to coincide with the advent of the CD era. The thick and gorgeous sound typical of the company is attractive. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.18 maintenance completed (POWER, meter SW internal adhesion reinforcement, power stage Tr check, pattern re-soldering, CR check in the drawer board, connector cleaning, meter logo lamp, C replacement in the power supply board, each SW.VO l. Cleaning, offset, bias adjustment, operation check, panel folding correction.)
Accessories: instruction manual
Main specifications: 270W+270W power guard circuit equipped with frequency characteristics 20 to 20 kHz damping factor 30 W 443 x H240 x D400 mm 37.2 kg
It looks like a novelty from the Sansui Vintage series. If placed under C-2301, etc., not only the sound quality but also the profound sense of appearance will increase (Murakoshi Yoichi)
Accessories: none
Main specifications: 4-sided polish W484 x H30 x D440 mm 17.5 kg
This disc stabilizer uses a “reversible structure” that allows both the front and back sides to be used. You can enjoy 2 types of sound quality depending on your preferences. High sound quality design with brass (special gloss finish) and damping rubber “Honeynight”. The exterior is dull, slightly scratched, etc. (Asaine Tomoho)
Accessories: none
Main specifications: H44 x W123 x D123 mm approx. 750 g
Maintained! A shell round needle model. The high range is soft and the bass is thick, and it is characterized by the thickness of the midrange represented by the bobbon-shaped frequency characteristics. The suppleness of the tone creates a sound field that you won't get tired of listening to. The exterior has dullness etc. due to use over time (Asaine Tomo)
Maintenance information: 2024.6.28 Maintained (pedestal installation, damper adjustment)
Accessories: original box needle cover
Main specifications: MC type output voltage 0.2 mV needle pressure 3 to 5 g internal impedance 2 ohms weight 31 g
Maintained! A round needle model that has become valuable. The high range is soft and the bass is thick, and it is characterized by the thickness of the midrange represented by the bobbon-shaped frequency characteristics. The suppleness of the tone creates a sound field that you won't get tired of listening to. It is dull and has a feeling of use. Cereals (Tomoho Asaine)
Maintenance information: 2024.6.28 Maintained (vibration system replacement shell replacement)
Accessories: original box
Main specifications: MC type output voltage 0.2 mV needle pressure 3 to 5 g internal impedance 2 ohms weight 31 g
Maintained! A CD/SACD player compatible with many formats in the high-resolution era. It is a higher-level model that incorporates a lot of technology, and the built-in 32 bit/192 kHz DAC allows you to enjoy pure sound with a wide range during SACD playback. It is designed with high sound quality for CDs and compressed files, so it is recommended for those aiming for high sound quality in any format. The exterior is good with no noticeable scratches (Ryo Mizusaki)
Maintenance information: 2024.6.28 Maintained (check for abnormal noise when opening the tray. Loading part dismantling, grease replacement, lens and disc table cleaning. I played each disc and checked analog, USB, and S/PDIF sounds)
Accessories: remote control, instruction manual, power cord
Main specifications: 32 bit/192 kHz twin D/A converter jitter reduction IC twin power transformer damper tray equipped with CDR-R/RW (MP3 MPEG-4 AAC WMA), DVD-R/RW (DSD [DSD disk], MP3, MPEG-4, AAC, WMA), iPod, iPhone, and iPad compatible W435 x H130 x D329 mm weight 7.8 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/27 sales price 79,800 yen Maintained! This is the first AUDIO OF OREGON control amplifier to arrive in a long time. It is compatible with 117V specification American speakers such as ALTEC and JBL, etc., and although it is a transistor, it doesn't become too stiff and makes you enjoy the firm sound. The exterior has dullness and scratches. ※The plug has been changed. Genuine RF Serial 02117 (Tamura Eiji)
Maintenance information: 2024.4.27 Maintained (board vibration check connection check. Flat amplifier module, all unit pattern parts added solder) 2024.4.13 maintained (electrolytic capacitor replacement in amplifier module. Pattern correction. (Voice operation check)
Accessories: No accessories
Main specifications: All stages use pure class A operation circuit input phono (mm/47 kΩ) tuner, tape, aux dimensions W483 x H89 x D190 mm weight 4.5 kg
The price has been drastically reduced! 2024/6/11 sales price 218,000 yen A special edition model commemorating the 70th anniversary of JBL's founding. The latest version that has been refined over the traditional 4312 series. A 12-inch diameter woofer unit equipped with the advanced 4429 is used. It is an all-round speaker with a sense of energy and good range extension. The exterior has dullness, small scratches, and threads. Serial 00687/00688 (Yonejima Satoshi)
Maintenance information: 2024.6.11 sweep test good
Accessories: saran net
Main specifications: 3-way bass reflex type 300mm woofer 125mm mid-range 25mm tweeter impedance 6Ω output sound pressure level 90dB frequency characteristics 44Hz to 40kHz W362 x H597 x D298 mm 25.2 kg
The disposal price has been reduced! Member prices are not applicable. 2024/4/19 sales price 79,800 yen ※1 unit only. Maintained! It is originally a professional mono amplifier, but there is only 1 unit. You can feel the strong power of the sound quality even with just one unit. It seems to be useful for mono and center speakers. There are scratches and paint peeling on the exterior. Serial Q001769 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (XLR speaker cable created (3 meters)). Electrolytic capacitor replacement. ATT cleaning. Solder correction. Rubber feet added. Bias offset check. Output audio check. Input ① GND ② HOT ③ GND (unbalanced) output ① not used ② is set to plus ③ minus 8 Ω load. (Also, a pop sound is made when the power is on and off, but this is a specification)
Accessories: speaker cable, power cable
Main specifications: 8 ohms W482.6 x H88 x D320 mm weight 13 kg
The disposal price has been reduced! Member prices are not applicable. 2024/6/1 sales price 69,800 yen Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. There are some scratches on the diaphragm on one side. Serial 60878/74750 (Yonejima Satoshi)
Maintenance information: 2024.6.1 Maintained (diaphragm installation adjustment, pad dampener installation, screw rust replacement. Wiring terminal contact cleaning, terminal dirt cleaning. Insulating bushing replacement. Diaphragm dirt cleaning. DCR (29324/6Ω diaphragm undamaged) DCR (33387/5.8Ω diaphragm damaged)
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
DENON's classic MC cartridge. The balance of localization and sound is excellent, and all music genres can be played without difficulty. It is a cartridge that can be recommended to a variety of people, from analog beginners to experts. Serial 5449 (Tamura Eiji)
Maintenance information: 2024.6.27 Operation confirmed
Accessories: needle cover
Main specifications: MC type output voltage 0.3 mV playback frequency 20 Hz to 45 kHz electrical impedance 40 ohms needle tip 16.5 microns round needle pressure 2.2 to 2.8 g dead weight 8.5 g
Maintained! An impressive 1-inch driver with a smooth, stretchy high range. Compared to the LE85, you can enjoy a natural sound with a sense of depth. As for the sound of a JBL, I get the impression that it is mild. There is a feeling of use on the exterior, such as dullness, small scratches, and peeling paint. Serial 33780 33949 (Hiroki Aso)
Maintenance information: 2024.6.27 Maintained (diaphragm installation adjustment pad, 2 dampers, replacement, distribution terminal, contact part cleaning, 8 insulation bushings, replacement, diaphragm dirt cleaning, DCR (33941/6.2 ohm diaphragm with small scratches)
DCR (33941/6.0 ohm diaphragm without scratches)
Accessories: none
Key Specifications: 1 inch driver, 8 ohm, crossover, 500 Hz, 108 dB, diameter: 114 x D98 mm, weight: 4.1 kg
The price has been reduced. 2024/5/20 sales price 19,800 yen ※Currently sold. Comes with enhanced power supply OBH-2. Creek MM phono equalizer. Although it has a compact body, it lets you hear bouncy low frequencies with good pitch. The response of the power lamp is slightly poor, but this is the current situation (Oikawa Tetsuji)
Maintenance information: 2024.5.20 Operation confirmed
Accessories: enhanced power supply OBH-2
Main specifications: Dimensions W100 x H62 x D125 mm Weight 360 g
The price has been reduced. 2024/4/29 sale price 24,800 yen A rare Rotel thin phono equalizer. It has a flat, neutral tone with no distractions, and I like how simple it is to use. There are small scratches, dullness, and the electrical outlet has changed (Oikawa Tetsuji)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual, original box
Main specifications: input sensitivity MM: 2.5 mV/47 kΩ MC: 210 mV/100 Ω size W440 × H72 × D195 mm weight 3.1 kg
The disposal price has been reduced! Member discounts are not applicable. 2024/6/17 sales price 49,800 yen tall tower audio rack. Made of powder-coated, scratch-resistant metal and tempered safety glass made in Italy. It has rounded glass front shelves for a custom made look. It includes a management system to hide power cords and interconnect cables. The exterior has a feeling of use such as dullness and small scratches. *Shipping costs will be estimated separately (Asaine Tomoho)
Accessories: none
Main specifications: shelf glass plate thickness 6 mm load capacity 23 kg size 635 x 610 x 1,550 mm weight 46 kg
The disposal price has been reduced! (Member price not applicable) 2024/4/12 sales price 70,000 yen B&W 805D series speaker stand. Equipped with a spike insulator “T-PROP”. It is a speaker stand with a completely new concept developed with the theme of eliminating speaker stress as much as possible by absorbing and releasing it in a natural way without putting a load on the diamond formation structure. The exterior has scratches, paint peeling, and bumps. (FUJISAWA KOSHI)
Accessories: insulator T-PROP, screws
Main specifications: top plate W227 x D306 mm B&W 805 Diamond, D3 specially designed bottom plate W280 x D360 mm height 500 mm approx. 15 kg
The disposal price has been reduced. Members are not eligible for discounts. 2024/6/14 sales price 238,000 yen Maintained! A popular preamp sold during the heyday of analog. The mid-range is more glossy and has a sexier vibe than those after C29. That rich sound can truly be said to be a preamp representing the golden age of Mackins'. There are scratches, small scratches, and partial peeling on the exterior. Serial AK1482 (Tamura Eiji)
Maintenance information: Maintained on 2017.7.8 (main volume contact cleaning (slight gang error may occur because parts are not available). Other switches, volume contact cleaning. Amplifier board electrolytic capacitor replacement. Panel lamp replacement. RCA terminal replacement. Correction of areas where panel peeling can be fixed. Check the operation of each input/output)
Accessories: instruction manual (English)
Main specifications: input terminals, RCA4, PHONO input, 2 pre-out systems, W430 x H140 x D365 mm, 13.8 kg
The disposal price has been reduced! Member discounts are not applicable. 2024/6/1 sales price 378,000 yen Maintained! The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its strong, dense sound. It has strong extrusion and is excellent compatibility with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. There are scratches and stains on the exterior, and rust can be seen on the top plate and back panel (Mizusaki Ryo)
Maintenance information: 2024.6.1 maintained (transistor in driver board, LDR, capacitor deterioration, GAIN, VOL noise, meter board capacitor deterioration, power supply board capacitor deterioration, meter lamp, display lamp deterioration → replacement. (Meter dismantling terminal lead wire soldering treatment, MODE SW dismantling cleaning, operation check, power stage check OK)
Accessories: power cord, copy of instruction manual
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
Compatible with micro SME short tonearm bases 3009 and 3010. There are dirt scratches on the exterior (Tamura Eiji)
Accessories: none
Main specifications: Compatible players: BL-101, BL-91, BL-111, etc.
It is an arm that inherits the basic design of the 3012 and has increased versatility with all players through downsizing. It is also attractive that the 2-split main weight is compatible with lightweight cartridges as well as heavyweight cartridges such as SPUs. Due to the sharp followability of the knife edge, the clear and cohesive sound quality still boasts high performance today. The exterior is slightly oxidized and dull. Serial 07031R (Satoshi Yonejima)
Maintenance information: 2024.6.26 operation confirmed
Accessories: connection cable
Main specifications: static balance type effective length 237 mm cartridge mounting weight range 9.5 to 34 g (including shell) needle pressure variable range 0 to 5 g
*Currently sold. It is inexpensive because the left and right shapes, the color of the cone paper and back logo, and model year are different. The classic 101 mm small speaker. The sound, which has been compiled in one small full-range shot, makes all kinds of popular music sound cheerfully. In addition to the exterior, as described above, you can see a feeling of use such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.5 operation confirmed
Accessories: none
Main specifications: 1 way 1 speaker impedance 6Ω maximum input 150W output sound pressure level 86db W232 × H154 × D172 mm 2 kg
※It is inexpensive because it has cracks. An acoustic lens mounted on JBL monitor speakers such as the 4343 series. By wearing it, the sound of the horn, which is too strong, is moderately diffused and calmed down. There is dirt and dust on the exterior (Tamura Eiji)
Accessories: none
The disposal price has been reduced! Member discounts are not applicable. 2024/5/18 sales price 39,800 yen Flat speaker using 600 neodymium magnets. It is built into a self-made enclosure. It is an audio speaker that is mainly used outdoors for station announcements and as a large digital signage product for outdoor use. As for the exterior, there are screw holes in the top plate, and there are dullness and small scratches all over (Yonejima Satoshi)
Maintenance information: 2024.5.18 sweep test good
Accessories: No accessories
Main specifications: MCMA multi-cell flat speaker impedance 8Ω frequency specification 90Hz to 10kHz W270 x H375 x D205 mm 5.2 kg (actual measurement)
The disposal price has been reduced. Member prices are not applicable. 2024/5/17 sales price 378,000 yen The flagship model of a Macintosh power amplifier with silver panel specifications. It is characterized by its strong, dense sound. It has strong extrusion and is excellent compatibility with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. There are scratches, dullness, and discoloration in places (Kojima Yosuke)
Maintenance information: Maintained on 2020.8.26 (2 input volumes, 4 semi-fixed volumes, 2 RCA plugs, 12 lamps, 8 electrolytic capacitors, replacement input mode switch disassembly cleaning, card edge cleaning, soldering, bias and offset check, output sound check)
(*The interior and exterior have been cleaned.)
Accessories: power cable
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
1 bottle only A rare 16Ω early model. An impressive 1-inch driver with a smooth, stretchy high range. Compared to the LE85, you can enjoy a natural and deep sound. Even though it's LE175, it is smooth and has a highly structured texture. The exterior has no paint peeling or gaskets. Serial 3943 (Fujisawa Yukishi)
Maintenance information: 2024.6.25 maintained (diaphragm installation adjustment, pad dampener, mounting screw rust replacement, distribution terminal contact part cleaning, terminal mold crack replacement, insulating bushing replacement, diaphragm stain cleaning, DCR (3943/10.5 ohm diaphragm no scratches))
Accessories: No accessories
Key Specifications: 1 inch driver, 16 ohm, crossover, 500 Hz, 108 dB, diameter: 114 x D98 mm, weight: 4.1 kg
The price has been reduced. 2023/6/15 sales price 5,000 yen Since the condition is poor, such as cracks in the body, it is currently being sold. A small full-range speaker that is compact, can be freely placed, and has a gentle impression. The sound quality is soft and the sound is relaxing. You can see a feeling of use on the exterior, body cracks, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2023.6.5 operation confirmed
Accessories: none
Main specifications: full range compact speaker, 8 ohms, maximum input, 40 W, W230 x H150 x D163 mm, 1.6 kg
The price has been reduced. 2024/6/16 sales price 79,800 yen The company's standard front load enclosure. The sound skips well, and it sounds crisp even with heavy units. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: front road horn system/floor type enclosure compatible speakers 2205, 2220, etc., minimum playback frequency 60 Hz, W752 x H914 x D610 mm, 46 kg
The disposal price has been reduced. Member prices are not applicable. 2024/5/20 sales price 198,000 yen Kappa series improved model Renaissance 90. The mid-high range is composed of EMIM and EMIT special units, and the sound is extremely delicate and clear. The deep sound field space and glossy, moisturized mid to high frequencies are unique to ribbon units. It has high resolution throughout the entire range and is suitable for classical and vocal styles. There are small scratches and line wounds, and there are repair marks of broken decorative plates at the foot (Oikawa Tetsuji)
Maintenance information: 2013.12.15 Maintained (exterior repair and cleaning. (Back side urethane deteriorated, replaced with substitute urethane)
Accessories: spikes
Main specifications: 4 way 4 speakers sealed floor type EMIT tweeter EMIM mid-range ribbon type 87dB 4Ω 250W W435 x H1245 x D315 mm 35.8 kg
The price has been reduced! 2024/6/23 sales price 25,000 yen Popular vacuum tube headphone amplifier. By adopting a double triode vacuum tube push-pull system, you can enjoy powerful and dynamic sound. It is also attractive that it has an impedance changeover switch that can be used with various headphones. The exterior has a feeling of use such as dullness and small scratches. Serial 11040004 (Tomoho Asaine)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: original box instruction manual power cord
Main specifications: 650 mW+650 mW 12 AU7 x 2 sticks 16 to 600 ohms W130 x H170 x D259 mm 3.5 kg
*Ordering a genuine brand-new remote control. Maintained by the manufacturer, including the replacement of a genuine new pipup! Mid-level model compatible with SACD. Equipped with a uniquely developed SACD/CD drive mechanism. The low frequency base has a firm sense of stability, and you can enjoy music with relaxed sound quality on both SACD/CDs. Recommended for those who want to enjoy SACD casually. The exterior is dull and has small scratches (Sasaki Shota)
Maintenance information: 2024.6.23 manufacturer maintained (laser pickup, loading belt, CD board capacitor replacement. (Others, inspection of each part, sound test)
Accessories: Power cable ※Remote control is being ordered
Main specifications: output terminal RCA · OPTICAL · COAXIAL · multi-channel SACD/frequency range 2 Hz to 100 kHz SNR 113 dB dynamic range 107 dB CD/ frequency range 2 Hz to 20 kHz SNR 118 dB dynamic range 100 dB dimensions W434 x H135 x D330 mm weight 7.4 kg
Lead wire missing. Lightweight ADC headshell similar to SAEC ULS-2. The finger tip is slightly longer and the shape is easy to hold. The exterior has small scratches, abrasions, and dullness over time (Murakoshi Yoichi)
Maintenance information: 2024.6.22 continuity confirmed
Accessories: none
Main specifications: dead weight 6g
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.21 Operation confirmed
Accessories: instruction manual, power cable
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
*Only 3 are 180mm pole (19mm diameter) quadraspires option, silver poles. If you are looking for additional poles such as Q4 or Q4D, don't miss it. There are small scratches and dullness on the exterior (Tomoho Asaine)
Accessories: No accessories
Key Specifications: 180mm length/19mm diameter optional pole
The disposal price has been reduced! (Member discounts are not applicable) 2024/6/7 sales price 89,800 yen ※The woofer cone is highly deformed, so it's cheap. Maintained in January 2024! It is a Harves speaker with increased appeal, such as the richness of the sound typical of an HL MONITOR. The Harves-like sound, which is characterized by a relaxed sound in addition to the mid-range density unique to those made in England, is attractive. Exterior maintenance has been carried out on the exterior, but in addition to scattering repair marks, there is a feeling of use over time, such as undulations on the woofer edge. *Saran net is not included. Serial 3349A 3349B (Tomonori Asaine)
Maintenance information: 2024.6.6 exterior repair maintenance (exterior chip repair (conspicuous areas only), front baffle painting) 2024.1.12 maintained (exterior repair stain colored front baffle repair polishing paint rear baffle cleaning
Woofer edge repair, protective agent application (with undulations), terminal replacement unit, detachable tweeter, corrosion, disconnection repair, diaphragm, dome coat treatment, 1 voice coil, bobbin deformation correction)
Accessories: none
Main specifications: 2 way 2 speakers, 22.5 cm cone woofer/2.5 cm soft dome tweeter impedance 8 Ω crossover 2,000 Hz sound pressure level 87 dB, W325 x H640 x D330 mm, 13.5 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/6/8 sales price 89,800 yen You can enjoy the voluminous bass with highly efficient and heavy corn paper. It is also durable with a gathered edge, and is also recommended for backload and front load enclosures. There are small scratches etc. on the exterior. Serial 7413 10417 (Tomonori Asaine)
Maintenance information: 2024.6.8 operation confirmed
Accessories: none
Main specifications: rated input 150 W frequency characteristics 30 Hz to 2 kHz 16 ohms efficiency 96 dB crossover frequency 800 Hz recommended enclosure volume 170 to 225 liters depth 146 mm 7.5 kg
Maintained. A horn-shaped tweeter developed for the D Series high range using plastic edges. 8Ω specification, compatible horn is CO-800. In addition to being sharp, it is characterized by a precise and delicate sound. Overall, there are dullness, small scratches, paint peeling, etc. (Oikawa Tetsuji)
Maintenance information: 2024.6.23 Maintained (distortion, vibration repair: magnetic circuit slit corrosion prevention, various parts stop noise, complete maintenance)
Accessories: none
Main specifications: Mid-high range driver, hard duralumin dome, plastic edge, frequency characteristics, 800 to 20,000 Hz, 102 dB, diameter 108 mm x D110 mm, 3.7 kg/bottle
※Since there are needle tip repair marks, it is inexpensive. A higher-level model that uses 6N copper as the coil winding for the standard DL-103 cartridge. Compared to the original model, the high range has been increased, resolution has been increased, and the sense of distortion has been reduced. There are no bends (Tamura Eiji)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: needle cover
Main specifications: round needle tip 16.5 microns output voltage 0.25 mV playback frequency 20 Hz to 45 kHz impedance 14 ohms needle pressure 2.5 g dead weight 8.5 g