Maintained. This is a heavyweight premain amplifier manufactured by PIONEER. Since they are only from the bubble period, large quantities of material were used, and they are highly cost-effective amplifiers. Even the smallest sounds are clearly reproduced, and the sound quality, which is both thick, shows how well crafted it was unique to that time. Overall there are small scratches, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.19 maintained (output relay replacement, master volume exchange, muting SW exchange, direct switch, etc., switch disassembly polishing grease application (input selector, recoup, loudness, tape 3, speaker switching SW), each volume, switch cleaning, interior and exterior inspection and cleaning, operation confirmation. * (Additional note) Since the master volume is a replacement, it can be adjusted in detail when the volume is low to medium volume, but when the volume is raised and auditioned, the VR seems to be raised (12:00). (*When listening to a phono, the sound will not come out unless the EQ switch is turned on)
Accessories: instruction manual
Main specifications: output 100W+100W (8Ω) 120W+120W (6Ω) 150W+150W (4Ω) power consumption 270W dimensions W420 x H162 x D435 mm weight 19.6 kg
Maintained, including the creation of a new dust cover. Comes with a SHURE M44G cartridge+PICKERING AS-2PS headshell, so you can enjoy it right after purchase. In addition to its thick, thick, and heavy sound quality, it is also equipped with an oil dump arm similar to the P-3 and an auto lift-up function, and it boasts overwhelming cost performance compared to current players in the same price range. The exterior, dullness, and feeling of use can be seen, but there is no noticeable damage (Kobayashi Hitoshi)
Maintenance information: 2024.6.30 Maintained (end sensor circuit tantalum capacitor replacement, end detection operation check)
2024.6.9 Maintained (arm disassembly grease wipe clean. Connector replacement. Electrolytic capacitor replacement. Each rotation lock adjustment. Arm operation, voice check. (Create a new dust cover)
Accessories: copy of instruction manual, adapter, oil case, SHURE M44G, PICKERING AS-2PS
Main specifications: Quartz PLL DC servo hole motor turntable diameter 31 cm 33/45 rotation oil braking system static balance S-shaped pipe arm compatible cartridge dead weight 4 g to 13 g W490 x H190 x D401 mm 15 kg
Maintained! A CD/SACD player compatible with many formats in the high-resolution era. It is a higher-level model that incorporates a lot of technology, and the built-in 32 bit/192 kHz DAC allows you to enjoy pure sound with a wide range during SACD playback. It is designed with high sound quality for CDs and compressed files, so it is recommended for those aiming for high sound quality in any format. The exterior is good with no noticeable scratches (Ryo Mizusaki)
Maintenance information: 2024.6.28 Maintained (check for abnormal noise when opening the tray. Loading part dismantling, grease replacement, lens and disc table cleaning. I played each disc and checked analog, USB, and S/PDIF sounds)
Accessories: remote control, instruction manual, power cord
Main specifications: 32 bit/192 kHz twin D/A converter jitter reduction IC twin power transformer damper tray equipped with CDR-R/RW (MP3 MPEG-4 AAC WMA), DVD-R/RW (DSD [DSD disk], MP3, MPEG-4, AAC, WMA), iPod, iPhone, and iPad compatible W435 x H130 x D329 mm weight 7.8 kg
A sharp Japanese vintage coaxial 2-way unit that uses a wide-angle cellular horn for the high range. If you supplement the low range with a bass reflex enclosure rather than tightening it up with an airtight seal, it seems that the level will increase dramatically throughout the entire band. There is a feeling of use throughout (Murakoshi Yoichi)
Maintenance information: 2024.7.2 operation confirmed
Accessories: none
Main specifications: 25cm coaxial 2-way 8Ω 95dB crossover 3.5kHz baffle opening 215φmm or 263φmm diameter 290 φmm depth 115mm 3.9 kg
The price has been drastically reduced! 2024/6/26 sales price 89,800 yen ※The exterior is in poor condition, so it's cheap. The EA-3 is equipped with a powerful power supply unit, and the exterior has also been completely redesigned with a refined design. The dual mono construction and non-feedback amplifier circuit reproduces smooth analog sound with an excellent sense of signal. The exterior has noticeable scratches on the top plate and front. Serial E31302005 (Yonejima Satoshi)
Maintenance information: 2024.6.26 operation confirmed
Accessories: No accessories
Main specifications: mm/MC compatible phono equalizer gain 38 dB (mm) 65 dB (MC) channel separation 100 dB or more, full stage symmetry, no feedback type, rated output voltage 200 mV (1 kHz) W310 x H86 x D316 mm 5 kg
An MC boost transformer that uses two transformers taken from the same console (microphone input transformer) in the 1940s. Detailed specs are unknown. The 2 system inputs can be switched with a toggle switch (Daiki Goto)
Maintenance information: 2024.7.2 storefront operation confirmed
Accessories: none
Main specifications: W100×D135×H100mm
The price has been reduced! 2024/6/12 sales price 37,800 yen*Model using 1.0 m pair plasma (powder of metallic compounds) shield for No. 3 HOT XLR cable. The synergistic effect of cryogenics and magnetostriction achieves an overwhelmingly high signal-to-noise ratio. The exterior is dull. Serial 10005476 (Yonejima Satoshi)
Maintenance information: 2024.6.12 continuity confirmed
Accessories: No accessories
The price has been reduced! 2024/6/12 sales price 37,800 yen RCA line cable 1.0 m pair model using plasma (powder of metallic compounds) shield. The synergetic effect of cryogenics and magnetostriction achieves an overwhelmingly high signal-to-noise ratio. The exterior is dull. Serial 100006156 (Fujisawa Yukishi)
Maintenance information: 2024.6.12 continuity confirmed
Accessories: No accessories
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand single point loads at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand a single point load at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
Comes with original box and hex wrench Set of 4 banana plugs, silver and rhodium plated in phosphor bronze, these banana plugs have a beautiful direct plating design. You can also increase the resolution on your own system. There is dullness and small wounds (Tamura Eiji)
Accessories: original box, hex wrench
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand a single point load at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
Comes with original box and hex wrench Set of 4 Y lugs Oyaide's screw-fastening Y lug terminals are made in Japan with excellent processing accuracy. This is a high quality sound plug that provides a wider range and a sense of density. There is little feeling of use (Oikawa Tetsuji)
Accessories: original box, hex wrench
Main specifications: Dual screw clamp system, pure domestic copper alloy (RoHS compatible), pure silver plating (1.5 μm) + platinum plating (0.3 μm), inner diameter 8.0 mm, compatible cable diameter 4.0 mm
Maintained! A shell round needle model. The high range is soft and the bass is thick, and it is characterized by the thickness of the midrange represented by the bobbon-shaped frequency characteristics. The suppleness of the tone creates a sound field that you won't get tired of listening to. The exterior has dullness etc. due to use over time (Asaine Tomo)
Maintenance information: 2024.6.28 Maintained (pedestal installation, damper adjustment)
Accessories: original box needle cover
Main specifications: MC type output voltage 0.2 mV needle pressure 3 to 5 g internal impedance 2 ohms weight 31 g
2M series RED. The good sound and fluttering energy typical of an orthophone are attractive. There are no noticeable scratches, but the needle cover is missing. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: instruction manual, original box
Main specifications: MM type 5.5 mV 20 to 22,000 Hz 47 ohms suitable needle pressure 1.8 g dead weight 7.2 g
※Since the cantilever is large and tilts to the right, it is inexpensive. Needle cover missing. The MC30S (MC30 Supreme), the upper model of the MC20S (MC30 Supreme) has a high output of 0.5 mV, which not only has a sense of dynamism and power, but is also characterized by a delicate and elegant high frequency. In classical music such as jazz and rock, there is a sense of depth in the performance, and it stretches well, and you can feel the luster of stringed instruments. There is a feeling of use on the exterior, such as dullness and scratches on the body (Murakoshi Yoichi)
Maintenance information: 2024.5.2 sound output
Accessories: case
Main specifications: MC type output 0.5 mV internal impedance 5 ohms needle pressure 1.8 g to 2.2 g dead weight 10.7 g
The price has been reduced! 2024/6/27 sales price 79,800 yen A shell oval needle features the original direct sound of the SPU. The sharp, firm, and powerful mid-low range and detailed expressiveness are attractive. There are fewer incidental sounds than the G-shell elliptical type, so you can enjoy an even more direct tone. The needle cover is partially chipped. Serial 412790 (Tamura Eiji)
Maintenance information: 2024.6.27 Operation confirmed
Accessories: needle cover
Main specifications: MC type 0.2 mV 3 to 4.5 g internal impedance 2 ohms load resistance 47 kΩ oval needle dead weight 23.6 g (mounter and screws included)
Maintained! A round needle model that has become valuable. The high range is soft and the bass is thick, and it is characterized by the thickness of the midrange represented by the bobbon-shaped frequency characteristics. The suppleness of the tone creates a sound field that you won't get tired of listening to. It is dull and has a feeling of use. Cereals (Tomoho Asaine)
Maintenance information: 2024.6.28 Maintained (vibration system replacement shell replacement)
Accessories: original box
Main specifications: MC type output voltage 0.2 mV needle pressure 3 to 5 g internal impedance 2 ohms weight 31 g
Maintained! Comes with a remote control. This model was created by gathering the know-how of the Integra series. There are only models produced with a thorough emphasis on sound quality, which is a bit different from other Integra series, and has a relaxed, relaxed sound. The exterior has dullness, threads, and small scratches. Also, the SP terminal has been replaced. Serial 6301012428 (Yonejima Satoshi)
Maintenance information: 2024.5.22 Maintained (disassemble the push switch and remote wire switch, polish the contacts, and apply contact cleaner. Volume contact correction. Remote control operation check OK)
Accessories: remote control, instruction manual
Main specifications: 155W+155W (6Ω) 120W+120W (8Ω) damping factor 400 (8Ω) frequency characteristics 2Hz to 100kHz W471 ✕ H170 ✕ D430 mm 26.6 kg
The price has been reduced! 2024/6/30 sales price 24,800 yen It is an audio system that combines various functions such as CD, SD, USB, AM/FM tuner, and Bluetooth in a compact body, and achieves an extreme level of elimination of noise that clouds music information. The exterior has marks on the top plate, and there is a feeling of use that is scratched (Hiroki Aso)
Maintenance information: 2024.6.30 Operation confirmed
Accessories: remote control instruction manual
Main specifications: Amplifier section rated output 19W+19W (4Ω, THD+N 0.4% or less, 2ch drive) SNR 100dB (IHF-A) speaker adaptable impedance 4Ω to 16Ω tuner section FM76.0 to 95.0 MHz AM522 to 1629 kHz preset number 15 stations SD section playback format MP3, WMA, WAV (48kHz24bit) recording format MP3 WAV (44.1kHz16bit) USB section interface USB2.0fullspeed file system FAT16, FAT32 playback format (front) MP3, WMA, WAV/FLAC (96kHz24bit) compatible sampling frequency 44.1 kHz16 bit recording format (front) MP3, WAV (44.1 kHz16 bit) connection to PC TypeB Bluetooth version 2.1 + EDR Profile A2DP1.2 codec SBC connection-related audio input terminal digital x 1 (OPTICAL) analog x 3 (TAPE/MD, LINE1, LINE2) PC x 1 (USB TypeB) audio output terminal analog x 1 (TAPE/MD) subwoofer pre-out x 1 speaker output terminal x 2 USB terminal front x 1 antenna terminal AM x 1 FM x 1 size W215 x H142 x D357 mass 4.8Kg
The disposal price has been reduced. Member discounts are not applicable. 2023/2/5 sales price 2,000 yen. *Currently sold. Specification details of only one Onkyo full range unit are unknown, but it was able to sweep and make sound. The exterior has dirt, dullness, and tape marks (Katsuji Hiura)
Maintenance information: 2023.2.5 sound output confirmed
Accessories: none
Main specifications: diameter 120 mm, depth 71 mm, screw pitch 219 mm (actual measurement), weight 1.2 kg
Maintained! A model designed with serious awareness of being compatible with the digital age. The range is wide, and the smooth mid-high range and tight bass are also attractive, and it is also recommended for use as an introduction to separations. There are many line scratches on the top plate, sides, etc. Serial 650713508 (Jun Tamai)
Maintenance information: 2024.6.21 maintained (cartridge selector, reckout selector, 1, 2, reckout switch, tape changeover switch disassembly, polishing grease application, equalizer, flat amplifier, power supply part solder repair, relay replacement, volume, switch cleaning, interior and exterior inspection, operation inspection)
Accessories: copy of instruction manual
Main specifications: MM/MC compatible W465 x H103 x D403 mm 8.5 kg
This is the first Nordst product to use patented micro monofilament technology for a 0.7 m pair of RCA cables. It is an inexpensive cable with good cost performance. ※The rubber on the single-channel terminal is out of stock (Tamura Eiji)
Maintenance information: 2024.7.3 continuity confirmed
Accessories: none
The price has been reduced. 2024/6/24 sales price 34,800 yen This is a well-made DSD-compatible USB-DAC. You can enjoy sophisticated playback sound with the wide range, high resolution, and amount of information unique to 1 bit (DSD). It has 3 input systems and 2 output systems, and has an upsampling function. It comes with a volume and can also be used as a DAC pre. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.18 Operation confirmed
Accessories: power cable
Main specifications: input/USB, OPTICAL, COAXIAL output/XLR, RCA PCM (24, 32 bit/32, 44.1, 48, 88.2, 96, 176.4, 192 kHz) OS/Windows 7, Windows Vista SP1 or later, Windows XP SP2 or later (Windows 8 compatible) W210 x H60 x D243 mm 2.6 kg
The winding of the mainspring is smooth and can produce sound, but there is rotation noise, unevenness, and sound shake, so it is sold as it is. The volume is not big, but I feel good in the middle and high range center. The appearance is rust of the age, there are dirt scratches Kusumi. (Takimoto Yutaka)
Maintenance information: 2021.12.1 operation confirmed
Accessories: handle
Main specifications: W358 × H260 × D295 6.85kg (actual measurement)
The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg
Pair Tube 45Special/38142 Compatible Ball Fishing Rod Type Filament Measurement Value 98/92 (Rejection Value 55) Geta Burns, is a bargain because it has decreased ※The pair is GM measured with the tester TV-7 Judgment is based on the value (Yosuke Kojima)
Accessories: none
2-row 6-piece outlet plate made of corrosion-resistant aluminum alloy+fully coated new metal There is a feeling of use such as small scratches (Kanai Hidetsugu)
Accessories: none
Main specifications: W120 x H116 x D6.5 mm weight 38 g
Maintained! NAKAMICHIN's pre-main amplifier is in stock for the first time in a while. Simple design like an English amp. The thick, energetic sound typical of Nakamichi is attractive. The exterior has dents, dullness, and small scratches on the top plate. Serial 07436 (Yonejima Satoshi)
Maintenance information: 2024.5.31 Maintained (power switch replaced. Output relay replacement. (Switch and volume contact correction)
Accessories: No accessories
Main specifications: 80W+80W (8Ω) equipped with Phonomm/MC W430 x H125 x D360 mm weight approx. 15.0 kg
Cartridge stand with acrylic cover made by N2 Factory. It is similar to the company's N2-S1, but it can hold 4 pieces. There are small scratches on the exterior (Hiura Katsuji)
Accessories: original box
Main specifications: W162 x H100 x D78 weight 500 g
Designed with a complete dual mono configuration from the power transformer. The pre and power are also independently configured. The high range is sparkling, and the mid and low frequencies are thick, making it a profound sound. The exterior has dullness, threads, and scratches on the front (Ryo Mizusaki)
Maintenance information: 2024.5.31 Maintained (The battery was replaced and the board pattern was corrected due to liquid leakage in the function memory battery. (Since the VR shaft is long, accuracy cannot be achieved, and stress is applied to the VR, so the extension shaft flexible joint Assy was replaced)
Accessories: remote control, instruction manual, power cord
Main specifications: effective output 85W+85W (8Ω) 170W+170W (4Ω) input: unbalanced (RCA) x 6 systems (1 system is PHONO: MM/MC compatible, 1 is TAPE) outer dimensions W440 mm x H95 mm x D400 mm weight 13 kg
Maintained! A pure Class A premain amplifier from the early days of the musical Fidelity. The top plate heats up due to the high calorific value, but it is a famous machine that still boasts high popularity for its elastic, bouncy mid-low range, and smooth, thick mid-high range sounds. The beauty of the simple design is also attractive. There are small scratches and scratch marks on the exterior. Serial 11418 (Tamura Eiji)
Maintenance Information: 2024.7.3 Maintained (input selector switch contact cleaning. The TAPR and MM/MC changeover push switches were replaced due to poor contact. 17 capacitors were replaced due to differences in electrolyte condenser fluid leak levels. (Each input/output operation check is OK)
Accessories: instruction manual
Main specifications: pure A grade 20W+20W (8Ω) W408 x H60 x D249 mm 5.5 kg
1 PIN is missing and only 3. Monster Cable's crimping banana plug has an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: crimping type φ4 mm
Speaker cable 3.8m+3.0m Device not processed. There is a description of Monster Cable, but the model number is unknown. The exterior has a feeling of use, such as stickiness, dullness, and writing on the sheath. (TAKAHASHI Nobuyuki)
Maintenance information: 2024.6.20 continuity confirmed
Accessories: none
The price has been drastically reduced. 2024/6/26 sales price 39,800 yen monitor audio 2-way bookshelf. The C-CAM unit introduced in the Bronze Series pursues sound quality. The high cost performance and sound typical of the company are attractive (Murakoshi Yoichi)
Maintenance information: 2024.6.26 sound output confirmed
Accessories: instruction manual, saran net, bass reflex sponge, jumper, rubber feet, hex wrench
Key Specifications: 2 Way 8Ω 85dB Crossover 2,500Hz W166 × H281 × D268 mm 5.0 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/6/4 sales price 79,800 yen Silver series adopted in woofers using new technology DCF. The unit, which has the familiar high-speed texture, is stored in a relatively large enclosure. The low range, which has more volume than the size, and the clear mid-high range with a wide range are attractive. The exterior has a feeling of use such as dullness. Cereals (Tomoho Asaine)
Maintenance information: 2024.6.3 sound output confirmed
Accessories: jumper cable (general purpose)
Main specifications: 2-way bus reflex type frequency characteristics 40 Hz to 35,000 Hz, crossover frequency 2,800 Hz, efficiency 88 dB, impedance 8 ohms, W230 x H375 x D329 mm, weight 9.3 kg/unit
Interconnect cable, 0.6 m pair, this is a standard cable for microphone cables without terminals. It also features soft sound quality and ease of handling (Murakoshi Yoichi)
Maintenance information: 2023.12.9 Continuity confirmed
Accessories: none
Disposal price reduction. 2024/4/10 sales price 3,000 yen*1 bottle only, currently sold as it is cheap. Bookshelf speakers made in England. It features compact, tight low frequencies and stretchy mid-high frequencies. There are scratches, threads, and the smell of oil (Daiki Goto)
Maintenance information: 2024.4.10 operation confirmed
Accessories: none
Main specifications: 89dB 6Ω W210 × H380 × D220 mm 5.4 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/11/8 sales price 49,800 yen ※The display panel moves when the volume etc. switch is pressed, but this is a specification. Maintained! MICROMEGA D/A CONVERTER It's a well-balanced European tune, and you can listen to chamber music and vocals smoothly. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.9.3 Maintained (replacement of tantalum electrolytic capacitors, replacement of other capacitance electrolyzed capacitors. Various digital signal demodulation tests confirm normal operation. (Rubber foot replacement)
Accessories: none
Main specifications: 1-bit input sampling frequency 32kHz,44.1kHz,48kHz W220×H55×D110mm 1.5kg
Compatible with micro SME short tonearm bases 3009 and 3010. There are dirt scratches on the exterior (Tamura Eiji)
Accessories: none
Main specifications: Compatible players: BL-101, BL-91, BL-111, etc.
※Surface deterioration is noticeable, so it is inexpensive. The die-cast aluminum shell has no screws, has a heavy weight, is sturdy, and the design is stylish and creative. The rigidity is high and low frequency tightness can be expected. The exterior has oxidation and dullness on the metal surface (Satoshi Yonejima)
Maintenance information: 2024.6.30 continuity confirmed
Accessories: No accessories
Main specifications: Die-cast aluminum, self-weight 10.6 g
Micro stroboscope It comes with an overhang gauge, so it's convenient to have one. There are small scratches and dents on the exterior (Yonejima Satoshi)
Accessories: No accessories
The disposal price has been reduced! (Member discounts are not applicable) 2024/6/21 sales price 898,000 yen This is the first arrival of the current model MA-2 Hi-Fi from the budding brand “Meitner” founded in 2011 by Canadian engineer Ed Meitner. Uses an unusual slot-in method. The resolution and wide range are truly high in potential. It has a good balance from high to low frequencies and seems to fit in with various systems. It is in good condition with no noticeable scratches. Serial 6135 (Fujisawa Yukishi)
Maintenance information: 2024.6.21 Operation confirmed (operation of the remote control and main unit is slightly relaxed, but this is a specification)
Accessories: remote control, instruction manual, power cord, original box, manual CD
Main specifications: CD player USB-DAC (compatible up to 192 kHz/24 bit, DSD compatible) coaxial digital x 1, USB x 1, USB x 1, W435 x H140 x D400 mm 9.0 kg
The disposal price has been reduced. Members are not eligible for discounts. 2024/6/14 sales price 238,000 yen Maintained! A popular preamp sold during the heyday of analog. The mid-range is more glossy and has a sexier vibe than those after C29. That rich sound can truly be said to be a preamp representing the golden age of Mackins'. There are scratches, small scratches, and partial peeling on the exterior. Serial AK1482 (Tamura Eiji)
Maintenance information: Maintained on 2017.7.8 (main volume contact cleaning (slight gang error may occur because parts are not available). Other switches, volume contact cleaning. Amplifier board electrolytic capacitor replacement. Panel lamp replacement. RCA terminal replacement. Correction of areas where panel peeling can be fixed. Check the operation of each input/output)
Accessories: instruction manual (English)
Main specifications: input terminals, RCA4, PHONO input, 2 pre-out systems, W430 x H140 x D365 mm, 13.8 kg
Maintained! with cabinet! Genuine Electri 100V specification. It is an intermediate model developed in response to MC2600 technology. It makes me fully feel the thickness and luster of the mid and low frequencies typical of McKinn, even at low volume. The total balance is good, and the combination with modern speakers is also good. The exterior has a feeling of use such as dullness, small scratches, and air bubbles on the panel. Serial FZ1679 (Tomonori Asaine)
Maintenance information: 2024.7.6 maintained (power stage Tr check, pattern re-soldering power meter SW internal reinforcement, capacitor replacement, SW, VOL cleaning lamp replacement)
Accessories: original box*cabinet is separate instruction manual copy foot
Main specifications: output 150 W+150 W (impedance 2, 4, 8 ohms), damping factor 40 or more, power guard, 1 kHz, overdrive up to 14 dB at 1 kHz, THD within 2%, W445 x H145 x D416 mm, weight 29 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/6/13 sales price 378,000 yen Maintained! This is a Baes regular model 100V specification. The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its strong, dense sound. It has strong extrusion and is excellent compatibility with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. In addition to a small scratch on the upper right front and a stain on the top surface, there is a slight feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.6.12 maintenance (GAIN VOL replacement, power stage Tr check, driver board Tr.C, meter, power supply board C replacement, MODE SW dismantling and cleaning, meter display lamp replacement)
Accessories: power cord, instruction manual (copy)
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
Maintained! The insulator on the bottom is currently out of stock, but it is being ordered from my home country. This is a super dreadnought mono power amplifier. Recommended for those who want to drive large speakers! The sound quality is natural and clearly expresses delicate parts. It is a power amplifier that has driving power and allows you to feel comfortable and at ease. There are small scratches on the exterior, but it is generally good (Daiki Goto)
Maintenance information: 2024.4.30 Maintained (meter acrylic removed, internal glass fog cleaning, all front lamps replaced. (Check that the lamp is on)
Accessories: instruction manual, power cable
Main specifications: 1200W (2/4/8 Ω) speaker output 1 system x 3 (2 ohm x 1, 4 ohm x 1, 8 ohm x 1) input terminal RCA x 1 system, XLR x 1 system, W445 x H313 x D540 mm 66.7 kg/unit