The price has been drastically reduced. 2024/6/21 sales price 218,000 yen Maintained! Genuine Yamagiwa model. It is a hidden popular model as the successor to the C26. It is an amplifier from the golden age of McKinn that is highly popular with music fans, with a sound reminiscent of a rich, thick vacuum tube sound. It makes vintage speakers sound intense. The exterior has paint floats, rust spots, etc. Serial BV1675 (Murakoshi Yoichi)
Maintenance information: 2024.6.21 maintained (each SW, VOL cleaning, lamp deterioration replacement, pin jack cleaning, earth plating wire treatment, poor push button SW contact → dismantling cleaning, operation check (gaps cannot be completely removed))
2022.2.4 Maintained (replaced due to poor noise compared to power circuit transistors. Electrolytic capacitor replacement. Selector switch contact cleaning contact grease application. Replace a dead lamp. The RCA terminal plating has peeled off and deteriorated, so it was replaced. (Each input/output operation test)
Accessories: instruction manual (copy)
Main specifications: input PHONO 1 · 2, AUX 1 · 2, TUNER, TAPE 1 · 2 W435 × H188 × D395 mm 11.8 kg
The price has been drastically reduced. 2024/6/13 sales price 378,000 yen Maintained! This is a Baes regular model 100V specification. The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its strong, dense sound. The extrusion is strong and goes great with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. In addition to a small scratch on the upper right front and a stain on the top surface, there is a slight feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.6.12 maintenance (GAIN VOL replacement, power stage Tr check, driver board Tr.C, meter, power supply board C replacement, MODE SW dismantling and cleaning, meter display lamp replacement)
Accessories: power cord, instruction manual (copy)
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
Valuable brand new and unused item! I opened it for photography and confirmation of operation. A popular model of Japanese record players. The chassis is tightly solidified into a heavyweight platter and a high-torque direct drive motor that rotates accurately and incomparably. It is a model that can be said to be the crystallization of Japanese craftsmanship, which has been thoroughly built using the direct attack method and enhanced physical characteristics. The heavy, thick sound that cannot be enjoyed with current direct drive players is attractive. The cover interferes slightly with the quartz lock indicator when the dust cover is opened and closed, but the current situation is. On the outside, there is mold floating on the platter. Serial E018872ZP (Fujisawa Yukishi)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: instruction manual, original box, head shell, handle, complete set of tools
Main specifications: Statically balanced S-shaped arm mounted applicable cartridge 3G to 12g direct drive drive quartz PLL servo control DC coreless hole motor turntable 36 cm aluminum die cast W545 x H230 x D417 mm 28 kg
Audio-Technica headshell. It is an attractive classic model with stable popularity and high versatility. The exterior is good with little feeling of use (Shota Sasaki)
Accessories: none
Main specifications: magnesium alloy body weight 10g
Maintained! Mid-range driver unit with YL acoustics. It's an energetic and clear sound typical of YL. The exterior has small scratches, dullness, and corrosion on the metal parts
Maintenance information: 2024.6.23 Maintained (improved internal terminal contact: improved contact between aluminum coil and terminal. Strain adjustment: complete maintenance of diaphragms, coils, and noise suppression)
Accessories: original box
Main specifications: Playback frequency band 200-7000 Hz maximum input 30W 8Ω output sound pressure level 102 dB diameter 110 x D120 mm 3.30 kg
Maintained. A horn-shaped tweeter developed for the D Series high range using plastic edges. 8Ω specification, compatible horn is CO-800. In addition to being sharp, it is characterized by a precise and delicate sound. Overall, there are dullness, small scratches, paint peeling, etc. (Oikawa Tetsuji)
Maintenance information: 2024.6.23 Maintained (distortion, vibration repair: magnetic circuit slit corrosion prevention, various parts stop noise, complete maintenance)
Accessories: none
Main specifications: Mid-high range driver, hard duralumin dome, plastic edge, frequency characteristics, 800 to 20,000 Hz, 102 dB, diameter 108 mm x D110 mm, 3.7 kg/bottle
※2-tier type. The size is one size smaller than the company's Q4D, etc., so the size setting is just right for those using compact systems such as LINN. There are line scratches and bumps on the top plate (Mizusaki Ryo)
Accessories: 4 optional spike bases
Main specifications: W395 x H255 D x 395 mm 4.0 kg (actual measurement)
The digital cable 1.0m BNC terminal STV6 silver clad OCC high-purity copper conductor has a parallel arrangement structure that neutralizes and makes the flow of electricity accurate, enabling more accurate transmission. It's clear, has no habits, and is easy to handle (Fujisawa Yukishi)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: original box
The digital cable 1.0m BNC terminal STV6 silver clad OCC high-purity copper conductor has a parallel arrangement structure that neutralizes and makes the flow of electricity accurate, enabling more accurate transmission. It's clear, has no habits, and is easy to handle (Fujisawa Yukishi)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: original box
The PE-101 reprint unit commemorating the 70th anniversary of Pioneer's founding is set in a dedicated enclosure that is well-made, such as using natural wood laminated wood as the material. Sound quality is balanced between good localization and playback band. There is dullness and small scratches. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: original box, saran net
Main specifications: 10cm full range single cone speaker 8Ω fo to 20,000 Hz 90.5 dB W154 x H246 x D204 mm, approx. 3 kg/book (actual measurement)
Digital cable, 1.0m, XLR terminal, silver-clad OCC high-purity copper conductor, has a parallel arrangement structure that neutralizes and makes the flow of electricity accurate, enabling more accurate transmission. It's clear, has no habits, and is easy to handle. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: original box
Digital cable 1.0m RCA terminal, silver clad OCC high-purity copper conductor, has a parallel arrangement structure that neutralizes and makes the flow of electricity accurate, enabling more accurate transmission. It's clear, has no habits, and is easy to handle. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: original box
Digital cable, 1.0m, XLR terminal, silver-clad OCC high-purity copper conductor, has a parallel arrangement structure that neutralizes and makes the flow of electricity accurate, enabling more accurate transmission. It's clear, has no habits, and is easy to handle. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: original box
Power cable 1.5m full tech “STUDIO POWER Series” power cable. PC TriPlex is used as the conductor, and the company's FI-11M and FI-11 plugs are used. The attack is strong, the response is high, and the vivid sound is attractive. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: original box
original needle. In addition to the delicate expressive power unique to light needle pressure, the thick, intense, energetic analog sound typical of Type 3 is perfect for jazz and rock. There are no bends (Tamura Eiji)
Maintenance information: 2024.6.23 sound output confirmed
Accessories: none
Main specifications: mm type frequency range 10 Hz to 25,000 Hz output voltage 3.5 mV needle pressure 0.75 g to 1.25 g weight 6 g
※Since there are needle tip repair marks, it is inexpensive. A higher-level model that uses 6N copper as the coil winding for the standard DL-103 cartridge. Compared to the original model, the high range has been increased, resolution has been increased, and the sense of distortion has been reduced. There are no bends (Tamura Eiji)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: needle cover
Main specifications: round needle tip 16.5 microns output voltage 0.25 mV playback frequency 20 Hz to 45 kHz impedance 14 ohms needle pressure 2.5 g dead weight 8.5 g
It hasn't been in stock in a long time! This is an orthonic luxury headshell. The sense of stability is different with the reinforced symmetry bar. There is paint peeling on the root of the connector. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: no accessories
Main specifications: dead weight 16g
Comes with original box! A popular ribbon-shaped super tweeter. Since it has a built-in network and high pass filter, it can be easily added to your system. Compatible with ultra-high frequency playback included in SACD and high-resolution sound sources. Rubber sheet marks remain on the top plate. There are no noticeable scratches on the exterior. Serial KD004330/KD004337 (Tamura Eiji)
Maintenance information: 2024.6.23 sweep check OK
Accessories: original box, instruction manual
Main specifications: Ribbon-type super tweeter 6Ω playback frequency band 9,000 Hz to 120,000 Hz W100 × H102 × D152 mm 1.3 kg/unit
2M series RED. The good sound and fluttering energy typical of an orthophone are attractive. There are no noticeable scratches, but the needle cover is missing. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: instruction manual, original box
Main specifications: MM type 5.5 mV 20 to 22,000 Hz 47 ohms suitable needle pressure 1.8 g dead weight 7.2 g
Silver interconnect with a 1.2m pair of RCA cables and LINN premium cables. Double shield construction using plenty of high-grade copper. The sound quality is natural, the resolution is high, and the deep bass is deep. Overall, there is a slight stickiness. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 continuity confirmed
Accessories: no accessories
LINN high performance MM cartridge ADIKT The cantilever is aluminum. It has good cutting and strength, and it plays jazz comfortably. (FUJISAWA KOSHI)
Maintenance information: 2024.6.23 Operation confirmed
Accessories: needle cover
Main specifications: mm type needle pressure 1.5 g to 2 g (1.75 g recommended) impedance 47 kΩ dead weight 7.0 g
Maintained in 2022. 60Hz specification. A record player system that combines Garrard's popular 401 phonomotor with Orthophone's dynamic balance tonearm RMG-212. It is a combination of an idler drive's powerful turntable and an arm that fully brings out the appeal of the SPU. The rich and expansive sound allows you to experience a scale not found in modern players. There is a feeling of use such as slight dullness on the motor part, missing letters, and small scratches on the cabinet. Serial 42395 (Murakoshi Yoichi)
Maintenance information: 2022.9.12 Maintained (full disassembly, inspection, diagnosis, chassis cleaning, dullness removal, motor: disassembly, degreasing, rust removal, polishing and height adjustment of elective disc brakes, rotor bearing lubrication, center adjustment. Spindle bearings: disassembly, cleaning, polishing, shaft rust removal, gasket replacement, oil leak treatment, lubrication. Idler: chemical cleaning, surface polishing with platter, heat treatment, bearing lubrication. Step pulley: cleaning, polishing, height adjustment. Power cable replacement, power switch: electrode damage correction, spark killer replacement, platter: degrease cleaning of idler contact surfaces, polishing, platter mat cleaning, metal label plate scratches, hairline finish. Continuous operation test, fine adjustment)
Accessories: none
Main specifications: 401: idler drive 33/45/78 rotation RMG-212: dynamic balance type, total length 300 mm, execution length 228 mm, overhang 16 mm, needle pressure range 0 to 7.5 g, direct reading arm base hole 22 mm, cartridge dead weight 7 to 32 g, W532 x H210 x D442 mm
This is an arm base with a built-in Ikeda arm elevation mechanism that can be adjusted while playing. In addition to the IT-345CR-1 and IT-407CR-1, it can also be used on FR-64, 66, etc. with a shaft diameter of φ25 mm. The body housing is machined from stainless steel, and the arm fixing part has a hybrid structure of stainless steel and brass. With a single dial operation, you can smoothly adjust the height even while playing a record, and you can maximize tone arm and cartridge performance. Good enough that you can't feel a feeling of use (Murakoshi Yoichi)
Accessories: stabilizer fixing tool, wrench, instruction manual, original box,
Main specifications: Height adjustment range: 10 mm up and down, pace mounting hole dimensions: φ41 mm, arm shaft: φ25 mm
LP record static removal brush. Upgraded model of the best-selling SK-2. It is rhodium plated to remove static electricity more quickly and reliably. Can also be used on CDs and DVDs (Murakoshi Yoichi)
Accessories: original box
Main specifications: brush specifications/tip = natural hair (black goat's beard) root = synthetic hair (acrylic fiber), thickness 46 denier, conductive fiber (copper sulfide chemically bonded to acrylic fiber) W60 x H170 x D30 mm 36 g
LP record static removal brush. Upgraded model of the best-selling SK-2. It is rhodium plated to remove static electricity more quickly and reliably. Can also be used on CDs and DVDs (Murakoshi Yoichi)
Accessories: original box
Main specifications: brush specifications/tip = natural hair (black goat's beard) root = synthetic hair (acrylic fiber), thickness 46 denier, conductive fiber (copper sulfide chemically bonded to acrylic fiber) W60 x H170 x D30 mm 36 g
Custom made internal wiring silver wire specification! It appears to be an unused item. Includes optional genuine phono cord HBC-MS-5000DR. A dynamic balance type long arm completed by Ikeda Isamu to surpass the masterpiece FR-66S he created himself. The materials for the main parts have been hybridized, and external influences have been thoroughly eliminated by adopting a spherical center block. The cable uses a double 2-core shield, a hybrid structure made of high-purity 6N copper and OFC materials (Murakoshi Yoichi)
Maintenance information: 2024.6.20 continuity confirmed
Accessories: instruction manual, original box, head shell, arm cable, template
Main specifications: Dynamic balance type, total length 388 mm, effective length: 307 mm, overhang: 12 mm, needle pressure application range: 0 to 5 g, arm adjustment range: 20 mm to 60 mm
Comes with original box! Coils using high-purity electrum (an alloy of natural gold and silver) have been developed. It features an advanced band-balanced sound quality that exudes an elegant and clean scent. The soft, natural, and delicate sound quality played by SPU Royal is unmistakably one of the greatest masterpieces. There is light dullness on the emblem. serial R3713
Maintenance information: 2024.6.18 sound output confirmed
Accessories: needle cover, instruction manual, original box
Main specifications: MC type output voltage 0.2 mV frequency characteristics 20 Hz to 60,000 Hz internal resistance 6 ohms diamond needle nudereplicant100 5 x 100 μm suitable needle pressure 3 g dead weight 31.5 g
Technics' flagship turntable SP-10R (list price 800,000 yen), which has taken over the SP-10 name to the present day, has an N2 Factory cabinet TT-10R (275,000 yen) double arm specification. The arm is equipped with Ikeda's short arm IT-345 CR-1 and SME 3012S2. It is equipped with a coreless direct drive motor with a double coil configuration, and pursues accurate and smooth rotation using a 3-layer heavyweight platter, etc. (Murakoshi Yoichi)
Maintenance information: 2024.6.15 sound output confirmed
Accessories: SP-10R original box, IT-345 original box, instruction manual, cabinet, phono cable (cable workshop TSUKASA WTS-P5200L, Ikeda HBC-MS-5000DR)
Main specifications: [SP-10R] direct drive 45/33/78 rotation (motor dimensions) W365 x H109 x D365 mm approx. 18.2 kg [IT-345 CR-1] dynamic balance total length 326 mm effective length 245 mm needle pressure application range 0-5 g [3012S2] static balance type needle pressure 0 to 5 g cartridge weight 1.5 to 26 g W490 x H195 x D504 mm control unit W110×H84×D350mm
Oyaide's multiple record stabilizer. Carbon FRP was used for the top and bottom disc tops in place of the previous model Texalum. Sound quality is further improved by the superior vibration treatment of carbon FRP. Weights can also be replaced (Mizushima Itsuro)
Accessories: instruction manual, original box
Main specifications: 1 top and bottom disc each (A5052 aluminum alloy cutting+carbon FRP) weight x 6, connecting shaft x 1 (brass chrome plated), weight spacer x 1 (EPDM rubber), 200g (no weight) to 440g (full weight attached) *Weight can be changed in 40g increments H35mm
Crystal glass stabilizer The high range stretches well, and the sense of distortion is reduced, so a variety of sounds can be produced (Mizushima Itsuro)
Accessories: original box
Main specifications: label installation surface/square top surface with a side of 57 mm/regular octagonal height with a side of 30 mm/40 mm weight 440 g
An innovative record stabilizer using an SVM mechanism. Nine stainless steel separate weights apply optimal load according to the record's fine sled, keep the disc flat, and effectively suppress vibrations. The colorations, which are reminiscent of the company's masterpiece arms of yesteryear, are also impressive. The exterior is good with little feeling of use (Murakoshi Yoichi)
Accessories: original box
Main specifications: external dimensions φ72 x height 21.5 mm weight 298 g
An Ikeda headshell with a beautiful polished surface finish. Machined aluminum alloy body with excellent rigidity. By making the terminal part made of titanium, it also has excellent vibration, resonance, and resonance (Murakoshi Yoichi)
Maintenance information: 2024.6.18 continuity confirmed
Accessories: original box
Main specifications: main body, aluminum terminals, titanium weight: 20g
Based on the idea and design of the SS-300, each item is carefully carved out with particular attention to materials and workmanship accuracy. It makes the sound very beautiful, and it reproduces a smooth sound (Mizushima Itsuro)
Accessories: instruction manual, original box
Main specifications: material, Alhaiz finish, anodized aluminum coating, outer diameter/diameter: 300 mm, thickness: 5.5 mm, weight: 845 g
PSE standard product A pure power supply box equipped with 2 power filter circuits with a separation connection design between high current devices/high noise devices and low current devices. Uses a 6-port Panasonic outlet. Small scratches are scattered on the exterior (Murakoshi Yoichi)
Maintenance information: 2024.6.18 continuity confirmed
Accessories: none
Main specifications: AC inlet specification, rhodium plated finish, W300 x H80 x D126 mm, approx. 2.4 kg
Discwasher record care system. The touch and grip when you hold it is reminiscent of a brush from a luxury shoe cleaning kit. It contains about half of the cleaner liquid. You can see the exterior, dullness, abrasions, and feeling of use (Murakoshi Yoichi)
Accessories: cleaning liquid, brush, instruction manual, original box
Main specifications: W121 x H60 x D58 mm (actual measurement)
The disposal price has been reduced. Member discounts are not applicable. 2024/4/25 sales price 448,000 yen Maintenance is being carried out in 2020. It's a famous machine you can't miss when talking about Marantz sounds of yesteryear. It has a good mid-range fat transfer, and its pleasant tonal feel is an appeal that cannot be obtained anywhere else. You can enjoy the Marantz sounds of the good times. There is some rust and small scratches on the exterior. Serial 8-4160 (Murakoshi Yoichi)
Maintenance information: 2020.11.18 maintained (AC code deterioration replacement, 40/40/20 μF and other deterioration replacement, 3 external paint, 20 μF x 2 deterioration exchange, selenium deterioration countermeasures → diode addition · vacuum tube 6BH6 noise exchange · vacuum tube socket and RCA jack caulking repair ※ other operation checked (measured at 32 to 41 W SP: 8 Ω with rated output AC 100 to 117 V) *A2 The EL34 vacuum tube guide pin is broken, but there is no problem with performance. (Part of the SP terminal on the right channel is missing.)
Accessories: instruction manual (for replicas, Japanese copy)
Main specifications: 35W+35W vacuum tube 6CG7/6BH6/EL34 W348 × H191 × D273mm 22.5 kg
German Sennheiser's highest-grade model! Even though they are headphones, these headphones have a unique sound style that can be heard at a distance from the sound image like a speaker. The sense of sound field is maximum in the dynamic type. The bass is modest and slightly tight, the mid-range is almost flat in terms of hearing, and the stretch that quickly passes through the audible band with almost no feeling of roughness in the high range is exciting. The exterior shows dullness and slight deterioration in the padding. Serial 02757 (Murakoshi Yoichi)
Maintenance information: 2024.6.21 sound output confirmed
Accessories: cable
Main specifications: dynamic headphone frequency characteristics 6 to 51,000 Hz 300 ohms 102 dB 370 g 6.3 mm standard plug cable length 3.0 m
※Operation has been confirmed, but since manufacturer support has ended, it will be handed over as is. The BDP-105DJP is a high image quality model equipped with cutting-edge image signal processing technology on the BDP-105JP. Equipped with 2 ESS Technology's flagship DAC chips ES9018, it is a media center that provides the latest media playback functions for high quality audio/AV systems. There are no major scratches on the exterior (Murakoshi Yoichi)
Maintenance information: 2024.6.22 sound output confirmed
Accessories: remote control, power cord
Main specifications: frequency characteristics 20-20kHz±0.2dB/96kHz-1.5dB SNR 130dB (A weighting auto mute) HDMI output video format 480i/480p/576i/576p/720p/1080p/1080p/1080p2k 3D frame packing 720p/1080p24 audio format PCM up to 7.1 ch/192 kHz DSD up to 5.1 channel Dolby Digital Dolby Digital Plus Dolby TrueHD DTS DTS-HD High Resolution DTS-HD Master Audio Terminals 2 Systems (AV Split Compatible) Diagnostic Video Output RCA Terminal 1 System Audio Output DA Converter ESS Technology ES9018S Analog RCA Output 7.1ch (max) stereo analog XLR output stereo digital output coaxial and optical: PCM Dolby Digital DTS headphone output up to 2ch/192 kHz HDMI input video format (including MHL) 480i/480p/576p/720p/1080p24/1080p25/1080p30 3D frame packing 720p/1080p24 Audio format up to 5.1 ch/192 kHz, or PCM Dolby Digital Dolby Digital Digital Plus DTS and AAC audio format (MHL) up to 7.1 ch/96 kHz PCM Dolby Digital Dolby Digital Plus DTS and AAC audio format (MHL) up to 5.1 ch/192 kHz PCM Dolby Digital Dolby Digital Plus DTS front 1 system (MHL compatible) 1 rear USB input front 1 system (USB2.0) rear 2 systems (USB2.0) audio format PCM up to 7.1 ch/192 kHz DSD USB-DAC input up to 5.1 ch/2.8 MHz USB-B terminal PCM up to 384 kHz DSD size W430 x H123 x D311 mm 7.9 kg
The i.LINK cable is 2.0m silver-coated, and both insulators use solid high density polyethylene. Both ends of the connector are 4-pin type (Tomonori Asae)
Accessories: original box
Maintained in 2023/12! A special edition of the PM-80. A popular Marantz model from the 90s that has both luster and strength. This is a geeky model where you can enjoy the difference in tone by switching between A grade and AB grade. There is a feeling of use, dullness, and small scratches. Serial MZ009119060022 (Yamato Yuki)
Maintenance information: 2024.6.23 sound output confirmed
2023.12.24 Maintained (replacement of defective output relay contacts. Polish the selector switch and other disassembly contacts and apply contact cleaner. I/O pin jack polish. Power supply circuit soldering correction)
Accessories: copy of instruction manual
Main specifications: AB class 100W+100W (8Ω) A grade 20W+20W (8Ω) size W454 x H165 x D380 mm weight 17.5 kg
The disposal price has been reduced! (Member prices are not applicable) 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier. The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg
Maintained! Premium air floating bearing belt drive player for enthusiasts. The ultra-heavyweight air float gunmetal platter has excellent regeneration power, high resolution in the low range that is difficult to distinguish, and the sense of stability in the mid to high range that is clearly positioned is perfect for a micro. Equipped with the FR-64FX, you can hear extremely sharp and sharp sounds. The exterior has a feeling of use over time, such as dullness and small scratches. Serial 02100371 (Hiroki Aso)
Maintenance information: 2024.6.20 Maintained (deteriorated capacitors, semi-fixed resistors, replacement, main unit, air pump unit, internal and external air hose joint replacement, rotation switching, SW contact cleaning, power supply, SW rotation adjustment, VR rotation adjustment, turntable, shaft disassembly, lubrication, motor disassembly, lubrication, internal rotor cleaning, post-lubrication, assembly arm disassembly, bearing replacement, exterior cleaning, pulley cover, repainting/cleaning, rotation speed adjustment needle after main assembly (Pressure check, speed check, sound output test, overall operation check)
Accessories: power cable pump unit belt handle
Main specifications: SX-777air gunmetal turntable weight 13 kg rated speed 33 1/3, 45 rpm rotation speed adjustment range ± 6% body/size W555 x D440 x H250 mm weight 46 kg air pump/size W200 x H122 x D366 mm weight 5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/6/15 sales price 148,000 yen Maintained by TEAC! VRDS-25 rigid menism final model. This is a popular model used by JAZZ/ROCK fans with a strong housing and a highly accurate VRDS mechanism, and has high resolution and clear contours. Spikes are attached to the solid 8 mm thick bottom plate, and the excellent construction with an excellent sense of reliability is also attractive. There is a feeling of use on the exterior such as small scratches and dullness (Asaine Tomoho)
Maintenance information: 2024.4.26 Maintained (All parts have been inspected. We have confirmed wear on the tray belt, clamp belt, and turntable bearings. Tray belt, clamp belt, and turntable bearing replacement. (Check operation by cleaning and lubricating the pickup and mechanical parts)
Accessories: Remote control instruction manual copy
Main specifications: multi-bit DAC, 25 bits, 8 times oversampling digital filter, W442 x H145 x D344 mm, weight 23 kg
Yamaha's new compact stereo CC-75 series speakers. Equipped with Yamaha active servo technology that reproduces rich deep bass even though it is small. The exterior has a feeling of use such as dullness and small scratches. Serial 646497Y0 646507Y0 (Takahashi Nobuyuki)
Maintenance information: 2024.6.3 operation confirmed
Accessories: saran net
Main specifications: 14cm woofer, 5cm tweeter, 1.1 cm super tweeter impedance 6 ohms, playback frequency band 40 Hz to 20,000 Hz, W200 x H330 x D239 mm, 4.3 kg
A record player equipped with Bluetooth and USB that has sold a total of approximately 1 million units worldwide. You can listen to the sound of records with your wireless speakers or wireless headphones. Since you can move freely within the range of Bluetooth radio waves, you can easily enjoy the sound of records. Furthermore, it is equipped with a USB terminal that can convert record sound sources into digital data. The condition is generally in good condition. *The included shell cartridge is out of stock. Serial 234198228 (Yamato Yuki)
Maintenance information: 2024.4.8 operation confirmed
Accessories: copy of the instruction manual, EP adapter, USB cable, phono cable (general purpose)
Main specifications: Direct drive system 33-1/3, 45 or 78 rotations/minute communication system Bluetooth standard Ver.5.2 compliant USB function 16 bit, 44.1 kHz or 48 kHz USB 1.1 compliant Microsoft Windows 8.1 or higher, MAC OSX or higher W452 x H141.6 x D352 mm 8 kg
DENON's pre main amplifier with excellent cost performance. It is also suitable for entry machines and second systems. There are threads and dullness on the exterior (Tomonori Asae)
Maintenance information: 2024.6.14 Operation confirmed
Accessories: ※Remote control missing power cord (general purpose product)
Main specifications: 70W+70W (8Ω) 140W+140W (4Ω) PHONO/MM/MC switching compatible W434 x H134 x D407 mm 14.6 kg
If you are looking for a 1.9 m HDMI cable, take this opportunity. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 continuity confirmed
Accessories: none
The disposal price has been reduced. Member prices are not applicable. 2023/12/10 sales price 25,000 yen*Since the output terminal has been remodeled to an XLR terminal, it is inexpensive. It is a pretty niche product that uses 2 stereo amplifiers so that it can be used like a mono amplifier. Actually, it seems to be a product intended for use with the company's 405-2. There is a lot of dullness on the exterior due to aging (Fujisawa Yukishi)
Maintenance information: 2023.6.4 sound output confirmed
Accessories: none
Main specifications: W80xH47xD140mm approx. 1.0 kg/unit
The price has been reduced. 2024/6/1 sales price 13,800 yen ※There is no problem with the sound output operation, but the LCD is dark and there are places where the characters disappear, so it's cheap. The company's first standalone USB-DAC and headphone amplifier compatible with DSD. This product took out the USB-DAC part of the company's CD player DCD-1500RE and finished as a standalone unit. Not only does it play music, but it also effectively upgrades the sound of movies and games on a PC. The exterior has noticeable scratches and paint chips on the top plate (Ryo Mizusaki)
Maintenance information: 2024.6.1 operation confirmed
Accessories: power cord
Main specifications: DSD signal sampling frequency 2.8224, 5.6448MHz sampling frequency PCM signal 32, 44.1, 48, 64, 88.2, 96, 176.4, 192 kHz input terminal USB (TypeB) x 1, optical digital input x 2, coaxial digital input x 1 output terminal analog audio output (L/R) x 1, headphone output x 1 (6.3 mm stereo standard jack) dimensions W170 x H57 x D182 mm weight 1.5 kg
The price has been drastically reduced! 2024/6/13 sales price 108,000 yen A phono equalizer amplifier equipped with a function to switch load impedance and load capacity according to the characteristics of the cartridge. Equipped with 2 line inputs, each position can be switched on the front side, and impedance settings can be adjusted with the back dip switch. There is a small scratch on the front (Sasaki Shota)
Maintenance information: 2024.6.13 operation confirmed
Accessories: original box, copy of manual, power cable
Main specifications: NF type equalizer (RIAA) input sensitivity: MM 3.2 mV, MC HIGH 0.37 mV, MC LOW 0.12 mV input impedance: MM 34 kΩ, 47 kΩ, 56 kΩ, 100 kΩ (switchable), MC HIGH 40 Ω, MC LOW 2.5 Ω input/output: 2 unbalanced systems/1 unbalanced system W364 x H81 x D274 mm 4.3 kg