Everything from the motor power supply to the tone arm has been fully maintained! New dust cover created! A player with a long-arm Ortofon AS-309S mounted on a TD-127. It comes with a dedicated optional weight, so you can use heavyweight cartridges such as SPUs. It has a high ability as a system, and it is a player that can play vividly regardless of genre, from classical to rock ※ The lifter works electrically, but since there is no sensor on the tone arm, auto stop or auto lift up is not possible (Oikawa Tetsuji)
Maintenance information: 2024.5.22 Maintained (deteriorated parts on the board, semi-fixed VOL for rotation speed adjustment, semi-fixed VOL replacement for sensor sensitivity adjustment. Front panel pitch adjustment VOL disassembly/contact polishing. Resolder the board. Disassemble and clean the arm. Drive belt replacement. Indicator lamp replacement. Grease up the platter bearing. Lubricate the motor shaft and disassemble and clean the clutch part. Floating, turntable rotation speed check, arm needle pressure check. Check the sound output. Chassis cleaning. (Comprehensive operation confirmation inspection)
Accessories: copy of instruction manual, optional weight
Main specifications: belt drive floating suspension 33/45/78rpm turntable 30cm zinc alloy 3.2kg double 16-pole synchronous motor speed fine adjustment range ± 6% W555 × H200 × D460 mm 20.4 kg
Fully maintained! The 38 series is the most popular 38FD. It has a warm tone with a warm tone, and there is plenty of warmth in the bass and mids, so you can enjoy the true essence of lackstone where you can enjoy the afterglow of the tone. There is slight rust on the back, but there are no major scratches other than that (Oikawa Tetsuji)
Maintenance information: 2024.5.22 maintained (solder correction, input/output waveform confirmation, load test (1kHz sine wave, at 8Ω load: 27W+27W), sound output test)
2023.12.17 Maintained (oil capacitor, block capacitor, electrolytic capacitor, film capacitor, fixed resistor, rectifier diode, DIN terminal, power supply SW, monitor SW, master VR, balance VR, rear panel VR, VR, rear panel VR replacement, RCA terminal polishing, lever SW disassembly and cleaning and application of grease to prevent oxidation and sulfation, replacement of 2 vacuum tube main parts, 50CA10 replacement, cabinet exterior repair/polishing/oil finish, input/output waveform Check, check for residual noise,
Load test (1 kHz sine wave, 27W+27W at 8 ohm load), sound output test)
Accessories: power cable, instruction manual
Main specifications: 30W+30W (4, 8, 16 ohms) line input 4 systems phono 2 systems (mm) W476 x H190 x D335 mm 18 kg
A CD player equipped with a DSD-compatible USB-DAC. The high quality playback sound is attractive due to the overwhelming amount of information and detail. The USB-A terminal on the front supports playback of iPods and USB memory devices, and a USB-B terminal (compatible only with PCs of the same age) is mounted on the back. There is a line scratch on the top plate, and the tray is slightly sticky (Oikawa Tetsuji)
Maintenance information: 2024.5.22 operation confirmed
Accessories: remote control, instruction manual, power cable, original box
Main specifications: 192 kHz/32 bit compatible DAC circuit, optical digital input x 1, USB (Type B) x 1, USB (Type A) x 1, analog audio output (L/R) x 1, optical digital output x 1, coaxial digital output x 1, W434 x H134 x D331 mm 8.2 kg
Exclusive audio rack made of wood fiber plywood and metal posts, with casters. The sturdy construction typical of TAOC is attractive. It is a rack where you can aim for stable sound quality without coloring. The effective height is 180 mm for the upper and middle steps and 230 mm for the lower tier. There are wounds, stains, abrasions, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: load capacity 1 stage 100 kg W600 x H835 x D550 mm 27 kg
Maintained! Comes with a remote control. This model was created by gathering the know-how of the Integra series. There are only models produced with a thorough emphasis on sound quality, which is a bit different from other Integra series, and has a relaxed, relaxed sound. The exterior has dullness, threads, and small scratches. Also, the SP terminal has been replaced. Serial 6301012428 (Yonejima Satoshi)
Maintenance information: 2024.5.22 Maintained (push switch and remote wire switch disassembly contacts are polished and contact cleaner applied. Volume contact correction. (Remote control operation check OK)
Accessories: remote control, instruction manual
Main specifications: 155W+155W (6Ω) 120W+120W (8Ω) damping factor 400 (8Ω) frequency characteristics 2Hz to 100kHz W471 ✕ H170 ✕ D430 mm 26.6 kg
Maintained! NAKAMICHIN's pre-main amplifier is in stock for the first time in a while. Simple design like an English amp. The thick, energetic sound typical of Nakamichi is attractive. The exterior has dents, dullness, and small scratches on the top plate. Serial 07436 (Yonejima Satoshi)
Maintenance information: 2024.5.22 Maintained (replacement of defective output relay contacts. (Switch and volume contact correction)
Accessories: No accessories
Main specifications: 80W+80W (8Ω) equipped with Phonomm/MC W430 x H125 x D360 mm weight approx. 15.0 kg
Set of 4 Quadraspires VENT black poles How about for an addition or replacement? There is some paint peeling on the exterior (Tamura Eiji)
Accessories: none
*The 2-tier rack decoupler spike holder is not included. You can see the attention to design and sound quality at a high level, such as slits that have been carefully thought out for heat dissipation effects and resonance, and solid aluminum pillars. There are some threads and bumps on the exterior (Tamura Eiji)
Accessories: none
Main specifications: W597 x H455 x D475 mm between shelves 326 mm
Luxpremain entry model. You can enjoy solid LUXMAN sound at an affordable price. We recommend combining it with European speakers that are glossy, soft, and have a good tone. The exterior is dull and there are abrasions and small scratches on the top plate. Serial M90410348A (Yonejima Satoshi)
Maintenance information: 2024.5.22 operation confirmed
Accessories: remote control, instruction manual, power cord
Main specifications: 70W+70W (8Ω) line input 4 systems (RCA x 4, XLR x 1), 1 phono system (MM), 2 tape systems W467 x H151 x D439 mm 13 kg
This is a double arm cabinet DK-2300 ideal for DP-80 and DP-75. The arm board can be easily removed with screws. One side of the armhole appears to be for the SME3012. Compatible models are unknown on the other side, and there is a 30mm diameter hole. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: insulated 70mm laminated plywood twin arm specification W600 x H101 x D 500 mm weight approx. 15 kg
Unspecified record player cabinet. Unprocessed The double arm is also mountable, and the construction is solid. If you've been looking for one, please take this opportunity. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W602 x H145 x D535 mm 13 kg (actual measurement)
※Whether it is a genuine product is unknown. Set of 8 1 pair of JBL speaker mount parts There is a lot of feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
A backload type enclosure that can mount an unspecified JBL38cm woofer. The construction is solid. If you've been looking for one, take this opportunity. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: saran net
Main specifications: W603 x H1100 x D508 mm 40 kg (actual measurement)
A full-range speaker with a high BOSE interior. 1 bottle only. An indoor speaker with high efficiency and clear sound quality. It is optimally designed for low-volume background music. The exterior has yellowness, dullness, dirt, scratches, etc., and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: mounting hardware
Main specifications: 5.7 cm full range driver x 1 allowable input 16 W impedance 8 ohms maximum sound pressure level 96 dB playback frequency band 90 Hz to 16 kHz W251 x H125 x D119 mm mass 1.8 kg
*Some SP terminal plates and screws on the OUT side are missing. A full-range speaker with a high BOSE interior. An indoor speaker with high efficiency and clear sound quality. It is optimally designed for low-volume background music. The exterior has yellowness, dullness, dirt, scratches, etc., and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: mounting hardware, instruction manual
Main specifications: 5.7 cm full range driver x 1 allowable input 16 W impedance 8 ohms maximum sound pressure level 96 dB playback frequency band 90 Hz to 16 kHz W251 x H125 x D119 mm mass 1.8 kg
Currently sold. The tuner's auto tuning is not working, but the current situation is. This K series CD/USB receiver is compatible with playback of iPods/iPhones, USB memory devices, etc. This is a flat, unobtrusive amplifier with a straightforward sound. It can also be connected to a PC and is recommended for those who want to get started with desktop audio. Appearance, dullness, small scratches, and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 operation confirmed (tuner auto tuning not working, other operations confirmed)
Accessories: remote control, power cord
Main specifications: 50W+50W W245 x H104 x D309 mm weight 5.7 kg
The classic 101 mm small speaker. The sound, which has been compiled in one small full-range shot, makes all kinds of popular music sound cheerfully. The exterior and color are different due to discoloration of the saran net, and overall a feeling of use such as dullness, abrasions, etc. can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: none
Main specifications: 1 way 1 speaker impedance 6 ohms maximum input 150 W output sound pressure level 86 db W232 x H154 x D172 mm 2 kg
*Some SP terminal plates and screws on the OUT side are missing. A full-range speaker with a high BOSE interior. An indoor speaker with high efficiency and clear sound quality. It is optimally designed for low-volume background music. The exterior is dull and has scratches (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: mounting hardware, instruction manual
Main specifications: 5.7 cm full range driver x 1 allowable input 16 W impedance 8 ohms maximum sound pressure level 96 dB playback frequency band 90 Hz to 16 kHz W251 x H125 x D119 mm mass 1.8 kg
Network attenuator pair sale inductance 0-2.7-3.4-3.6-3.9-4.7mH allowable input 400W W105 x H92 x 76 mm 1.9 kg/piece with original box (Kojima Yosuke)
Accessories: original box
Maintenance was carried out, including the replacement of internal deteriorated capacitors! This is Marantz's masterpiece power amplifier model 5, which has not arrived in a long time. Not only is the range unbelievably wide when viewed from the year it was released, but the excellent driving power and glossy tone are truly a masterpiece with a high reputation. There are scratches and paint peeling on the exterior. Serial 1017/1024 (Fujisawa Yukishi)
Maintenance information: 2024.5.21 Maintained (AC cord film deterioration → rewiring procedure. ◎ Common · 1 x 2 inch nuts added for bottom legs (please be careful when opening the back side) · 20 μF or other deterioration replacement and additional 4 x 2 · selenium deterioration → diode addition, BIAS and AC BAL readjustment, vacuum tube socket and RCA jack caulking repair. *Other operation checks have been performed (measured at 30 to 41 W SP: 8 Ω at rated output AC 100 to 117 V)
Accessories: No accessories
Main specifications: mono tube power amplifier output 30W (UL connection) EL34 push pull W152 x H186 x D378 mm 13.4 kg
Maintained! It is the 5th generation of the 907, the top model in the D series that continues to be popular. Brush-ups have been made, such as strengthening the power supply section from the previous game, and the ability to reproduce the low frequency range has been improved. Precision is also added to the wild Sansui sound that feels torque, making it fun to listen to classical music. The exterior has line scratches, threads, and chips in the corners. Serial 605104895 (Fujisawa Yukishi)
Maintenance information: 2024.5.21 maintained (tone, subsonic, CD direct, muting, input selector (all), reck-out, phono selector switch disassembly polishing grease application, output relay replacement, protector transistor replacement, power supply unit, constant current diode, resistor exchange, selector lamp replacement, adjustment volume replacement, solder repair, SP selector fixed, master volume, other VR Cleaning, internal inspection cleaning, adjustment inspection, operation confirmation. (*Relay operation takes 15 to 20 seconds)
Accessories: No accessories
Main specifications: 160W+160W (8Ω) PHONO (MM/MC) compatible W466 x H161 x D431 mm 26 kg
Maintained! Best buy model from the late 90s. It inherits the traditional diamond actuation circuit, and is characterized by a well-balanced sound with a refined circuit configuration, such as a sense of SN in the mid-high range, and the certainty of the outline in the low range. The exterior has scratches, etc. Serial 608024137 (Fujisawa Yukishi)
Maintenance information: 2024.5.21 maintained (input selector, power amplifier direct, reck-out, processor, MM/ MC changeover switch disassembly, polishing grease application, speaker 1/2 tone, ride ness, subsonic switch replacement, output relay replacement, solder repair, protector capacitor replacement, adjustment inspection, operation confirmation)
Accessories: No accessories
Main specifications: 80W+80W (8Ω) phono (MM/MC) switching dimensions W432 x H165 x D450 mm weight 18 kg
Maintained! The mid-range α series uses an α-X balance circuit that blocks the effects of noise and distortion from the ground. The smooth, stretchy sound quality is attractive. Designed with CD playback in mind, the sound separation is good, and it is a classic premain that will keep you entertained regardless of genre. There are line marks and threads on the exterior. Serial 437100950 (Fujisawa Yukishi)
Maintenance information: 2024.5.21 maintained (tone, source switch, MM/MC switch disassembly, polishing grease application, power amplifier circuit transistor, adjustment volume replacement, output relay replacement, power supply part solder repair and other main parts solder repair, each volume, switch cleaning, interior and exterior inspection and cleaning, operation confirmation)
Accessories: No accessories
Main specifications: 90W+90W (8Ω) W448 x H160 x D441 mm 16.0 kg
Maintained. 300B single amplifier using all Tamura transformers. It is a configuration that firmly holds the basics of a single amplifier using a rectifier tube. Furthermore, you can use it safely with 300B DC ignition with a regulator (Oikawa Tetsuji)
Maintenance information: 2024.5.21 maintained (2 main volume gang error replacements, CV378/GZ37 deterioration replacement, RCA jack and vacuum tube socket caulking repair*Other operation checked with AC100V (rated output measured at 8W SP: 8Ω))
Accessories: none
Main specifications: used vacuum tube 300B 6SL7/GZ37/5U4G/5X4G output 7W x 2 W430 x D215 x H210 mm 19 kg
Maintained! A prime amplifier developed during the heyday of CDs and gained popularity. The powerful, punchy sound quality, which combines the quality of the mid-high range with the power of the low frequencies, is attractive. There is room not found in lower models, and you can enjoy the sound with a sense of scale typical of SANSUI. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 maintenance completed (tone and other switch disassembly polishing grease application (loudness, turnover, subsonic, muting, processor, input selector, power amplifier direct, source direct, tape, reckout switch), output relay, headphone relay replacement, power supply transistor replacement, power amplifier circuit transistor replacement, resistor, adjustment volume replacement, solder repair , interior and exterior inspection and cleaning, bias, DC adjustment, confirmation of each input/output, operation inspection)
Accessories: copy of instruction manual
Main specifications: Advanced α-X circuit equipped with 160W+160W (8Ω) damping factor 150 (8Ω) Phonomm/MC compatible W460 x H159 x D446 mm weight 33 kg
A long-selling Technica model that includes a shell and cartridge. The sound quality is clear and bright, and it makes popular music in general bouncy. The exterior has a feeling of use such as dullness (Jun Tamai)
Maintenance information: 2024.5.21 sound output confirmed
Accessories: original box
Main specifications: VM type playback frequency band 20 to 20,000 Hz output voltage 5 mV needle pressure 1.5 to 2.5 g H26 x W36 x D67.5 mm dead weight 19.5 g (including shell)
The price has been drastically reduced. 2024/5/20 sales price 198,000 yen Kappa series improved model Renaissance 90. The mid-high range is composed of EMIM and EMIT special units, and the sound is extremely delicate and clear. The deep sound field space and glossy, moisturized mid to high frequencies are unique to ribbon units. It has high resolution throughout the entire range and is suitable for classical and vocal styles. There are small scratches and line wounds, and there are repair marks of broken decorative plates at the foot (Oikawa Tetsuji)
Maintenance information: 2013.12.15 Maintained (exterior repair and cleaning. (Back side urethane deteriorated, replaced with substitute urethane)
Accessories: spikes
Main specifications: 4 way 4 speakers sealed floor type EMIT tweeter EMIM mid-range ribbon type 87dB 4Ω 250W W435 x H1245 x D315 mm 35.8 kg
The price has been reduced. 2024/5/21 sales price 248,000 yen genuine Baes product. Comes with a wood cabinet. A control amplifier representing Mackin's golden age. Compared to the C28, this model has a wider range and more subtlety. The rich, glossy, and thick tone is alive and well, and it plays particularly well with vintage speakers. There are stains and small scratches on the exterior as a whole, and there are bubbles around the knobs of the glass panel and around the SW (Sasaki Shota)
Maintenance information: 2018.3.15 Maintenance completed (each SW/VOL cleaning, *BASS/TRE chips could not be removed. LDR, bridge diode, and illumination lamp replacement. C, R, etc. check, peeling correction only on the upper and lower parts. (*Some corrections are not possible)
Accessories: copy of the manual
Main specifications: frequency characteristics 20 Hz to 20 kHz input terminals PHONO 1 · 2, AUX, TUNER, TAPE 1 · 2 W406 × H138 × D330 mm 8.6 kg
Digital cable 1.0 m RCA plug This 75 ohm digital cable is ideal for generating clocks such as clock generators, word clock connections for receiving devices, S/PDIF connections to DACs, audio interfaces, DJ devices, etc., and video equipment. The exterior is dull (Fujisawa Yukishi)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: original bag
An ultra-high purity 6nCu with a digital RCA cable 1.0m pure silver coating is used as a single wire. Double shield structure with soft copper wire braids layered on top of aluminum PET tape. A two-layer sheath structure that controls unnecessary vibrations by covering the outer circumference of the shield with a RoHS-compatible PVC sheath. The exterior is generally beautiful with no conspicuous scratches (Tamai Jun)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: original box
Self-made 4ch power amplifier using 4 Flying Mall digital power amplifiers DAD-M1. The construction is solid, and the sound is high resolution, just like a flying mall. Recommended for those who want to save space and use it for multiple purposes. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.20 sound output confirmed
Accessories: power cable
Main specifications: DAD-M1 rated output 160W/4Ω 100W/8Ω frequency characteristics DC to 25kHz/4Ω DC to 50kHz/8Ω S/N ratio 120dB overall size W270 × H162 × D290 mm weight 6 kg (actual measurement)
Self-made 4ch power amplifier using 4 Flying Mall digital power amplifiers DAD-M1. The construction is solid, and the sound is high resolution, just like a flying mall. Recommended for those who want to save space and use it for multiple purposes. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.20 sound output confirmed
Accessories: power cable
Main specifications: DAD-M1 rated output 160W/4Ω 100W/8Ω frequency characteristics DC to 25kHz/4Ω DC to 50kHz/8Ω S/N ratio 120dB overall size W270 × H162 × D290 mm weight 6 kg (actual measurement)
The price has been reduced! 2024/5/20 sales price 148,000 yen JBL large horn set 2360H and 2360T. It's perfect for those who want to experience the intense and open sound of a horn. A self-made mounting stand is also included, so you can quickly attach it to the enclosure. In addition to dullness and small scratches on the exterior, there is a feeling of use such as peeling paint (Hiroki Aso)
Accessories: self-made stand
Main specifications: 2360H 2 inch driver radial horn recommended crossover 500 Hz overall size W792 x H786 x D894 mm weight 18.2 kg (actual measurement)
RCA cable 2.0m pair LC-OFC Class 1 is a long-selling product capable of pure signal transmission that has been produced for over 10 years. The balance is impressive with flat, tight bass and smooth high-frequency luster. The exterior is dull and has a feeling of use (Hiroki Aso)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: none
The price has been reduced! 2024/5/19 sales price 478,000 yen A digital processor that inherits DP-720 technology. ES9018 manufactured by ESS Technology is operated in parallel. It is especially recommended for Accuphase CD players and transports. The SN is good, the sound has good visibility, and is excellent compatibility with high resolution and PC audio. The exterior is generally beautiful, although there are small scratches on the top plate. Serial A5Y134 (Yamato Yuki)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: instruction manual power cable
Main specifications: digital input HS-Link x 1 coaxial x 2 TOS link x 2 USB x 1 XLR x 1 USB 5.6448 MHz (1 bit 2 ch DSD) 384 kHz (32 bit 2 ch PCM) high resolution compatible dimensions W465 x H114 x D385 mm weight 14.4 kg
The price has been drastically reduced. 2024/5/19 sales price 158,000 yen Maintained. The Lux tubular premium FM/AM tuner WZ-30 was developed with the aim of being the ultimate FM stereo tuner. With the warm and thick sound quality typical of a tube ball, you can enjoy broadcasting in a relaxed atmosphere. The circle of the manufacturer logo on the front is off (Oikawa Tetsuji)
Maintenance information: 2024.5.19 Maintained (2 STEREO/MONO switching relays unstable replacement, 1 μF defective and deterioration replacement, 3 FM sensitivity improvement measures → vacuum tube 6CW4 replacement 3 (using supplies) · Noise improvement measures → 2 additional 0.002 μF Mylar capacitors · FM and AM circuit IF/RF/MPX re-adjustment
(*Operation has also been checked with AC 100V)
Accessories: copy of instruction manual
Main specifications: tubular FM/AM tuner W470 x H175 x D275 mm 10 kg
RCA cable 1.0m pair oxygen-free copper OFC Ritz wire 2-core shield plug, standard AccuPhase line cable with gold plating. The sound is more gorgeous than the L-10. There are dullness and scratches around the plug, and abrasions on the sheath (Kojima Yosuke)
Accessories: none
The price has been reduced! 2024/5/19 sales price 848,000 yen This is a special edition model that uses precious Santos rosewood wood as the decorative layer for the B&W popular bookshelf 805D3. The deep brilliance of the body, which was lacquered 13 times, is reflected in sound quality. The sense of realism where sound particles can be picked up in detail is one of the highest degrees of perfection in 805 history. The exterior is not conspicuous, but there are threads on the top of the TW, etc. Serial 0211/0212 (Yonejima Satoshi)
Maintenance information: 2024.5.19 sweep test good
Accessories: instruction manual, saran net, jumper cable
Main specifications: 2-way bass reflex 8Ω 88dB W238 x H424 x D345 mm 12.6 kg
The SINTRA series, which is Lloyd's hidden masterpiece, and the rare SINTRA IMPROVED have arrived. Using a dome tweeter jointly developed with SCAN SPEAK, a uniquely designed bass reflex port reproduces clear sound with reduced resonance. The sound absorbing material around the tweeter is peeling off, there are small scratches, and dents (Daiki Goto)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: original box
Main specifications: 2 way 2 speakers, 8 ohms, W305 x H203 x D190 mm, weight 7.8 kg (actual measurement)