Genuine Electri FIRST WATT, the personal brand of PASS LAB designer Nelson Pass, is now in stock. It is characterized by a smooth, good tone characteristic of A grade. Excellent compatibility with high efficiency speakers of 95 db or more. Although it is a low-cost version, it boasts the same quality as a high-end model. The exterior is dull, and there is a small scratch on the back of the top plate. Serial 1343 (Fujisawa Yukishi)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: instruction manual, power cord
Main specifications: pure A grade amplifier 25W+25W (8Ω) 180W W430 × H143 × D390 mm weight 12.28 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/1/31 sales price 49,800 yen ※The finish is slightly different on the left and right, so it's cheap. JBL professional 38cm woofer. A lightweight, rigid curved cone is used for the diaphragm, and the bright, energetic bass reproduction is attractive. Serial 12526/12669 (Takasaki Atsushi)
Maintenance information: 2024.1.30 Operation confirmed
Accessories: none
Main specifications: recommended crossover 800 Hz or less 16 ohms (measured 17/18 ohms) effective enclosure volume 170 to 285 L diameter 388 x depth 138 mm
※It has been replaced with a rubber edge. A masterpiece of full range units. The overhang of the sound from mid-bass to mid-range is excellent, and the vocals resonate sensually with a life-size sound image. There is stickiness on the inside of the frame. Serial 125664/125654 (Oikawa Tetsuji)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: none
Main specifications: 20cm full range Alnico magnet 8Ω 89dB input 40W depth 98mm approx. 3.5 kg/bottle
ALTEC's royal unit used in A7 etc. It's a woofer with a good sense of clarity and a light sound. It has a sense of dynamism and goes well with jazz and rock (Shota Sasaki)
Maintenance information: 2024.3.18 sweep test good
Accessories: none
Main specifications: 38cm ferrite magnetic woofer, 97db, 8Ω, 20Hz to 1600Hz, weight 9.4 kg, baffle opening diameter 35.9 cm
Sony Theatre System Tallboy Speaker The sweep test is good, but since the corn paper has dents, it is currently sold at a low price. This speaker is easy to use with both front and rear speakers. There are small wounds and dullness (Sasaki Shota)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: nothing
Main specifications: W60 x H1050 x D60 mm bottom 250 mm weight 3.4 kg (actual measurement)
※Since the remote control is out of stock, it is cheap and is currently sold. Basic DENON stereo premain amplifier. The range is wide, and the glossy tone is attractive. It is an easy-to-use, well-balanced model that is suitable for both introductory use and secondary use. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.3.18 sound output confirmed
Accessories: instruction manual (copy)
Main specifications: 50W+50W (8Ω) phono (MM) 1 line input 5 system headphone terminal with pre-out W434 x H121 x D337 mm 7.1 kg
※6 month warranty. The new Q series q300 is the successor to the iQ series. It is a coaxial unit with a creative shape, and its relaxed, gentle sound and excellent sound field feel are attractive. It has an excellent sense of positioning when the volume is low. There is a feeling of use on the exterior, such as line scratches on the front, scratches on the top plate, and scratches on the corners (Mizusaki Ryo)
Maintenance information: 2024.3.18 sound output confirmed
Accessories: jumper cable
Main specifications: 2-way bass reflex bookshelf speaker frequency characteristics 42Hz-40kHz (±3dB) crossover frequency 2.5kHz 87dB W302 x D210 x H355mm weight 7.7 kg
A standard model of domestic mono cartridges. A popular model that condenses the appeal of a mono needle, which has a thick overall sound and is also powerful. It is also attractive that the output is high and can be used without a step-up transformer (Oikawa Tetsuji)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: needle cover
Main specifications: output voltage 3 mV playback frequency 50 Hz to 10 kHz impedance 240 ohms compatible load 1 kΩ or more needle tip 17 microns diamond round needle needle pressure 3G
Maintenance was completed in 2020, but there is a slight gap left on the ATT on one side. ALTEC's crossover variable frequency network. The graininess and sound cuts are also impressive. With this network, you can easily switch horns and drivers in various ways. There are stains and scuff marks on the exterior. Serial K340599/K340611 (Sasaki Shota)
Maintenance information: 2020.7.19 Maintained (rust removal (pickling) treatment for back terminal screws and bridge plates, front terminal orientation correction, increase, deadline change, SW contact cleaning, ATT disassembly, contact grease application, frequency characteristic measurement check (~ approx. 42 kHz), and continue to use the original capacitor for good results, input/output waveform and balance confirmation sound output check)
Main specifications: Crossover 500 Hz, 800 Hz, 1200 Hz switched with a jumper, banana plug input compatible W191 x H110 x D350 1.8 kg/bottle
This is Altec's classic 1 inch 4-sectional horn. With a 1-inch driver of your choice, such as the 802-8D, you can enjoy the horn sound unique to Altec with good sharpness. There are small scratches on the exterior (Sasaki Shota)
Accessories: none
Main specifications: crossover 500 Hz directional horizontal 90 x vertical 40 throat diameter 250 mm W600 x H270 x D 486 mm 6.7 kg
It has been replaced with a JICO 192-VN35E replacement needle. It combines the delicate expressive power unique to light needle pressure with an energetic, thick sound typical of Type 3. Recommended for those who listen to jazz and rock (Oikawa Tetsuji)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: none
Main specifications: mm type frequency range 10 Hz to 25,000 Hz output voltage 3.5 mV needle pressure 0.75 g to 1.25 g weight 6 g
This classic headshell is made of magnesium alloy and has an attractive, unobtrusive sound. Overhang and left/right tilt adjustments are possible. The exterior is dull and has corrosion marks (Wang Zhan)
Maintenance information: 2024.2.22 continuity confirmed
Accessories: none
Main specifications: dead weight 10g
The die-cast aluminum shell has no screws, has a heavy weight, is sturdy, and the design is stylish and creative. The rigidity is high and low frequency tightness can be expected. There is a feeling of use on the exterior such as scratches and dullness (Tamai Jun)
Maintenance information: 2024.3.1 sound output confirmed
Accessories: none
Main specifications: Die-cast aluminum, self-weight 10.6 g
※There is no compatible cartridge, so it has not been checked. Replacement needle for Audio-Technicavm type cartridge AT23 If you use it, be sure to use it as a stock. There is no bending or sticking to the cantilever, and the stylus is clear and sharp (Tamai Jun)
Maintenance information: 2024.3.16 unchecked
Accessories: original box screwdriver
800 Diamond is deeply popular. It's a powerful monster speaker with both sound and design. The specifications of the tube-loading diamond dome tweeter make you feel the potential that does not fit within the frame of a monitor speaker. The high-fidelity reproduction picks up even the slightest sound effects of the sound source. There are small scratches on the exterior and some impact scratches on the stand. Serial 0000625/0000626 (Kanai Hidetsugu)
Maintenance information: 2024.3.17 sound output confirmed
Accessories: instruction manual, saran net, spikes, jumper cables, phase plugs
Main specifications: 3 way 4 speaker bass reflex playback frequency band 25 Hz to 33 kHz nominal impedance 8 Ω (minimum 3.1 Ω) crossover frequency 350 Hz/4 kHz W450 x H1180 x D645 mm 102 kg/book
An AR 3-way bookshelf developed as a successor to the AR-3 a. The traditional acoustic suspension system is adopted, and it has excellent low frequency reproduction with wide range. There are corners on the exterior and back, there are a few abrasions, and there is a feeling of use such as dullness (Kobayashi Hitoshi)
Maintenance information: 2024.3.17 Operation confirmed
Accessories: saran net, jumper
Main specifications: 3-way acoustic suspension system 6.5 ohms 85 dB W375 x H625 x D275 mm 24.3 kg
* There is no problem with operation, but in addition to ATT being chipped, the exterior is poor, so it is cheap and sold as is. The younger brother model of the NS-1000M. Equipped with a carbon woofer and beryllium tweeter, this is an attractive car with a transparent sound reminiscent of the NS-1000M. There are many repair marks on the exterior, sides, etc., and there is a feeling of use due to corrosion, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.3.18 Operation confirmed (sweep OK, ATT crackdown)
Accessories: None (Saran net missing)
Main specifications: 3 way 3 speakers sealed 40 Hz to 20,000 Hz 91 dB 6 ohm W374 x H678 x D324.5 mm 23.5 kg
Maintained by the manufacturer in 2014. It is an open reel deck that is easy to handle and has excellent functionality and sound quality. The TEAC sound is clear and has good visibility, but the thickness is just right, so you can fully enjoy the analog feel. In addition to corrosion and paint deterioration on the exterior and plating part, characters disappear on part of the meter, there is a feeling of use such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2014.10.28 manufacturer maintenance completed (mechanical parts replacement, mechanical ASSY disassembly/cleaning/lubrication, implementation of each SW/VR, and jack contact correction, and other parts cleaning/inspection/adjustment)
Accessories: No. 10 clamper
Main specifications: 4 tracks, 2 channels, 6 heads (recording x 2, playback x 2, erase x 2), maximum use reel No. 10 tape speed 19/9.5 cm/sec W432 x H440 x D210 mm 20.0 kg
There is no problem with the sound output, but since there is a slight gap in the attenuator, it is inexpensive and is sold as is. A model designed to be compatible with digital sources. The clear outline of the tone gives the impression that it sounds regardless of genre. It is also recommended as an introductory machine. There are stains on the exterior and edges, abrasions on the top plate, sides, etc., veneer peeling on the bottom, and overall there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.3.17 operation confirmed (sweep OK, ATT is slightly brittle but disappears when turned, sold as is)
Accessories: saran net
Main specifications: 3 way 3 speakers 6Ω 92dB W315 × H585 × D320 mm 17 kg
There are bends on one shaft, dullness, and logo peeling, so it is inexpensive. Set of 4 Technica's classic banana plug. Insert the core wire that has been stripped of the cable coating into the hole on the side of the product and tighten the product back in place to fix the cable. (KOBAYASHI Hitoshi)
Accessories: none
Unspecified level gauge. If you're looking for something smaller, take this opportunity. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Maintained! In addition to “High Voltage/High Current,” which is a unique amplifier technology, the HK series premain amplifier was created by adding new sound quality improvements. It's not flashy, but the full, astringent mid-range makes you listen to an attractive, stable sound. On the exterior, you can see a feeling of use such as scratches and dullness. Serial S158-04254 (Jun Tamai)
Maintenance information: 2024.3.18 Maintained (L channel output transistor 2SC3281 2SA1302 2SC3298A short circuit replacement adjustment semi-fixed VR 10KΩ 1KΩ 4 locations poor contact replacement idling adjustment output board solder crack available solder repair sound output confirmation for each input/output connection ※ Since this machine does not have a speaker relay, there are times when a small crackling sound is made when the power is turned off, but there is a problem because it has already been adjusted Senshi)
Accessories: copy of instruction manual
Main specifications: output 120W+120W phono input/MM only with video input terminal W443xH160xD405mm weight 15.5 kg
It is an analyzer that can measure the listening room environment and speakers. Measurements can be performed in the 20 Hz to 20 kHz band. It is also battery-operated, compact, and easy to use. The exterior is dull, and there is a feeling of use such as scratches. Serial MC5J21B003 (Jun Tamai)
Maintenance information: 2024.3.18 simple check OK
Accessories: original box microphone
Main specifications: oscillation signal wobble tone (modulation frequency 8 Hz) oscillation frequency 20 to 20 kHz (measurement point 31) power supply 9V battery (S-006P x 1) microphone: back electret condenser type omnidirectional frequency characteristics 20 Hz to 20 kHz power supply 1.5V (SUM-3 x 1) W430 x H53 x D158 mm 1.0 kg
※Unopened Replacement roller and brush set for AT-6004J. *Please note that we have not been able to confirm the detailed condition of the product due to dents in the case (Takahashi Nobuyuki)
Accessories: none
※Unopened Replacement roller and brush set for AT-6004J. *Please note that we have not been able to confirm the detailed condition of the product due to dents in the case (Takahashi Nobuyuki)
Accessories: none
※Unopened Replacement roller and brush set for AT-6004J. *Please note that we have not been able to confirm the detailed condition of the product due to dents in the case (Takahashi Nobuyuki)
Accessories: none
Sound quality is prioritized, such as silver contact switches, gold-plated terminals, silver-plated OFC internal wiring materials, etc., and there is little change or deterioration in sound. The exterior has a feeling of use such as dullness and small scratches (Asaine Tomoho)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: No accessories
Main specifications: W180xH65xD130mm 0.58kg
RCA cable is a standard BELDEN line cable with a 1.5m pair of plugs that clearly outlines the sound while having a firm thickness in the mid to low range. There is a feeling of use such as dullness on the plug part (Hiroki Aso)
Maintenance information: 2024.3.18 continuity confirmed
Accessories: none
AT14ea/g with shell. This is an Audio-Technica VM cartridge, and the sound is bright and light, typical of Technica. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: none
Main specifications: VM type needle pressure 1.0 to 2.0 g (optimal 1.8 g) 10-20,000 Hz elliptical
Basic model in the AT100 series. There is a sense of dynamism like a Technica, with firm mids and sharp treble, and you can tell how high CP is in the entry class. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: none
Main specifications: VM type playback frequency band 18 to 20,000 Hz output voltage 4.0 mV standard needle pressure 1.4 g dead weight 6.8 g
Rack QAVM Series Set of 4 256 mm Poles This length is useful when installing medium power amplifiers, etc. The exterior has peeling paint and small scratches (Takahashi Nobuyuki)
Accessories: none
Main specifications: length 256 mm diameter 19 mm
The sound is clear and bright, and it plays particularly popular music very well. This cartridge is suitable for introduction to analog. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: none
Main specifications: VM type needle pressure 1.5 g to 2.5 g dead weight 5.8 g
※Since there is no ground cable at both ends, it is inexpensive. 0.75m phono cable XRR series tonearm cable. It is a neutral oriented sound with thick, powerful sound quality typical of Audiocraft, and has no habit. The exterior is dull and has abrasions around the plug (Takahashi Nobuyuki)
Maintenance information: 2024.3.18 Continuity confirmed
Accessories: none
Set of 4 This is a black pole, an option for 180mm pole (19mm diameter) quadraspires. Please use it as an additional pole for Q4, Q4D, etc. There are paint peeling and small scratches on the exterior (Takahashi Nobuyuki)
Accessories: none
Key Specifications: 180mm length/19mm diameter optional pole
Set of 4 struts set for the company's “MSMK2” series of racks. How about changing the length, adding shelves, etc. (Takahashi Nobuyuki)
Accessories: none
FOSTEX network film capacitors. If you like clear and speedy sound, go for it. The exterior is generally good (Takahashi Nobuyuki)
Maintenance information: 2024.3.18 sound output confirmed
Accessories: none
Main specifications: capacity 0.22 μF, insulation voltage 120/240 (VAC/VDC), body dimensions W62 x diameter 23 mm, drawing line length 80 mm each
TEAC's electric brush-type stylus cleaner has a needle tip cleaning effect due to slight vibrations in the circular part of the tip. Use after moistening it with a stylus cleaner or the like. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: none
Set of 4 blue coin insulators Vibration (resonance) and impact noise are simultaneously damped, and overall resolution is improved with excellent vibration countermeasures. It is particularly excellent at improving low-frequency resolution. The exterior is dull, scratched, etc. (Takahashi Nobuyuki)
Accessories: none
Main specifications: diameter 25 mm, weight 4 g
※Unopened Replacement roller and brush set for AT-6004J. *Please note that we have not been able to confirm the detailed condition of the product due to dents in the case (Takahashi Nobuyuki)
Accessories: none
Orthophone MM cartridges with high cost performance. Although it is an inexpensive model, the cartridge has a solid sound, and is sharp and easy to listen to. The exterior is generally good (Takahashi Nobuyuki)
Maintenance information: 2024.3.18 Operation confirmed
Accessories: original box instruction manual needle cover
Main specifications: MM type 20 Hz to 21 kHz output voltage 4 mV needle pressure 1.75 g
Maintained! It has a calm tone typical of a British monitor, but the graininess is good, and it blends in smoothly with a natural sound. The sound of strings such as cello and violin adds smoothness and luster, and you can feel a unique sense of elegance. There are a few small scratches, repair marks, etc. on the exterior ※Please use a dedicated speaker cable (Tomoho Asaine)
Maintenance information: 2024.3.15 Maintained (exterior maintenance (cleaning, stain coloring, chip repair/touch up), front baffle repair/paint, saran net maintenance (internal urethane repair/net replacement), woofer maintenance (cleaning, bestilene cone coating)
Mid maintenance (cleaning, besctren corn coating)
Tweeter maintenance (disassembly cleaning/lead wire correction) super tweeter maintenance (grill painting/adhesive/cleaning) cable creation/terminal bracket polishing unit detachment)
Accessories: Saran net speaker cable
Main specifications: 4 way 4 speakers 8 ohms 30 to 20,000 Hz crossover 700/3,000/13,000 Hz W396 x H802 x D422 mm (actual measurement) 32.1 kg (actual measurement)
The price has been drastically reduced. 2024/3/17 sales price 1,000 yen. 1 bottle only Unspecified horn tweeter. Conduction was confirmed, and sound was confirmed (Murakoshi Yoichi)
Maintenance information: 2024.3.15 continuity confirmed
Accessories: none
Main specifications: 95 mm in diameter, screw pitch (diagonal): 86 mm, depth: 53 mm
The disposal price has been reduced. Member discounts are not applicable. 2024/2/18 sales price 34,800 yen Wharfedale model number unknown woofer. It's very similar to the 12-inch woofer mounted on the W70D. Equipped with Alnico magnets, inverted dome edge. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.2.17 Operation confirmed
Accessories: none
Main specifications: aperture (from outside the edge to outside the edge) 283 mm screw pitch (screw diagonal) 316 mm depth 149 mm measured impedance 10/12 ohms
The disposal price has been reduced. Member discounts are not applicable. 2023/1/31 sales price 5,000 yen. This is a pair of Pioneer mid-range attenuators. Details of the mounted model etc. are unknown. Operation of conduction only has been confirmed (Murakoshi Yoichi)
Maintenance information: 2022.10.22 continuity confirmed
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2023/2/5 sales price 2,000 yen. *Currently sold. Specification details of only one Onkyo full range unit are unknown, but it was able to sweep and make sound. The exterior has dirt, dullness, and tape marks (Katsuji Hiura)
Maintenance information: 2023.2.5 sound output confirmed
Accessories: none
Main specifications: diameter 120 mm, depth 71 mm, screw pitch 219 mm (actual measurement), weight 1.2 kg