※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.17 Conductivity confirmed
Accessories: none
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer The terminal is male and cannot be used as a microphone. There are a few indelible writing marks left on the plug (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
The large triode print sold in Japan has disappeared, but I think it was made by NEC from the structure. Measured IP value: 45 mA (the best standard IP value for this amplifier is 50 mA) with the original box ※ I checked the sound output with the test amplifier and measured the plate current value, and it has been determined that the operation is good (Kojima Yosuke)
Accessories: original box
Unspecified power cable 2.0m. The plug is Panasonic WF5018K, and the connector is made by Global Electronics. This cable is relatively easy to handle. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.5.5 continuity confirmed
Accessories: none
※1 piece only (male to male) XLR cable 1.5 m interconnect cable with unknown manufacturer. There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
Maintained by the manufacturer! Yamaha's pre-main amplifier equipped with a floating and balanced amplification power amplifier using a MOS FET. A screw fastening system is used for the connection, and thorough consideration has been given to low impedance. Equipped with a phono equalizer with MC head amplifier. The smoothness and strength of the sound are perfectly balanced, and no source is selected from records to high-resolution sound sources. The appearance is good, with a slight dullness. There are a lot of scratches on the remote control (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 Maintained (replacement of power supply related resistors, etc. in the main board and INPUT board. Operation check confirmation)
Accessories: remote control, instruction manual, power cord
Main specifications: output 90W+90W (8Ω) 150W+150W (4Ω) input 7 systems (phono MM/MC) dimensions W435 x H157 x D463 mm weight 23.4 kg
Internal and external maintenance has been applied and brushed up. The vivid sense of dynamism and the sharpness of the high frequencies typical of YAMAHA have been revived. It has a low frequency thickness that 1000 monitors don't have. It is a timeless masterpiece with a clear sense of transparency, upper and lower driving force, and the smooth connection, and the heavy exterior with an ebony finish that stands out at a glance even today. It is in good condition due to maintenance. Serial 11478L 11478R (Yamato Yuki)
Maintenance information: 2024.4.1 operation confirmed
2023.9.4 Maintained (exterior repair/polishing/clear finish. Rear baffle repair/painting. Saran net replacement. Unit frame painting. Network maintenance (Since the terminals have already been replaced with external products, adjust the direction and tighten, apply a screw fastener, and replace the mounting screws. ATT contact status check (check that there are no gaps). A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Input/output waveform and balance check, sound output check) Unit detachable)
Accessories: saran net
Main specifications: 3-way sealed playback frequency band 40Hz to 20kH sound pressure level 90dB rated input 50W maximum allowable input 100W impedance 8Ω crossover frequency 500Hz/6kHz dimensions W395 x H710 x D349 mm 39 kg
※Since it is cheap, it is currently sold. This is a thin center speaker. Since it has an anti-magnetic design, this model is easy to use and easy to combine with other speakers. Recommended for those who are building surround sound for the first time. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 sound output confirmed
Accessories: instruction manual, connection cord, original box
Main specifications: 2 way, 3 speakers, bass reflex system, center type, anti-magnetic design, playback frequency band 60 Hz to 20 kHz, 88 dB, 6 ohms, allowable input, 40 W, W435 x H100 x D221 mm, 2.2 kg
Speaker cable, 2.5 m pair, SOS3+ single connection, Y lug specification on both ends, standard model of the company's speaker cable. There is little dramatization, and the sound is light (Kojima Yosuke)
Accessories: none
The disposal price has been reduced! (Member prices are not applicable) 2024/5/14 Torrens entry model with sales price 118,000 yen. Although it is an entry model, the silence and smoothness of the belt drive, and the delicate sound are attractive, and the tone arm is easy to adjust. Recommended for entry-level belt drive machines. There are a few small scratches on the exterior. Serial 00262803 (Fujisawa Yukishi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: copy of instruction manual, power cord, connection cord, spike base, original box
Main specifications: W420 x H125 x D330 mm 8 kg Drive system: belt drive motor: synchronous motor speed: 33 1/3, 45 rpm electronic speed selection platter: diameter 300 mm, 3 kg, aluminum power supply unit housing tone arm: static balance type
Phono equalizer with USB output. An analog signal can be imported into the PC by connecting the target PC (Windows 8, 7, Vista, XP, Mac OS) to the USB terminal on the back. Impedance switching between 10Ω, 100Ω, and 1kΩ is possible by combining the attached short pins, and is compatible with various MC/MM cartridges (Ryo Mizusaki)
Maintenance information: 2024.5.26 Operation confirmed
Accessories: original box
Main specifications: gain 40dB (1kHz) input impedance mm47kΩ+220pF fixed, MC47kohm+1nF (adjustable with plug) W150 x H50 x D117 mm 511g (main unit)
The price has been drastically reduced. 2024/5/15 sales price 118,000 yen Maintained! A famous direct drive machine representative of Technics. The torque is high, the start and stop times are extremely short, and the stable operation that immediately enters constant speed is unique. It also drives LP heavyweights without difficulty. Overall there are small wounds, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (due to disconnection of the FG coil in the motor core, the FG/ angular velocity detection coil was taken out after disassembling the motor core, and the coil pack was rewound. The rotation speed has been reset)
Accessories: copy of instruction manual, power supply unit
Main specifications: Direct drive aluminum die-cast turntable 33, 45, 78 rotating body W365 x H100 x D360 mm 9.5 kg power supply unit W110 x H85 x D300 mm 3.8 kg
A direct drive record player equipped with an Orthophone 2M RED as standard equipment. The built-in PHONO equalizer allows direct line connection to an audio device (conventional PHONO input connection is also possible with the back switch). It is also equipped with a simple auto lift-up function (there are times when it is not compatible depending on the width of the inner groove), so beginners and advanced users can easily enjoy the subsystem deeply. There is a black spot on the start/stop switch (Kojima Yosuke)
Maintenance information: 2024.5.25 Operation confirmed
Accessories: manual, power cable, connection cable, original box, genuine shell, cartridge (2M RED)
Main specifications: Direct drive universal S-shaped tone arm, static balance arm, effective length 230 mm, overhang 15 mm, applicable cartridge, 14.3 to 20.7 g (including headshell) when using auxiliary weights, 18.7 to 25.1 g (including headshell) output terminal/PHONO terminal x 1, PHONO ground terminal x 1, LINE output terminal x 1, LINE output terminal x 1, LINE output terminal x 1, W453 x H169 x D372mm 9.9kg
A new standard model for the SL-1200 series, inheriting the efforts and results that began with the development of the SL-1200G. Outstanding reliability and stability are now available at an affordable price. I'm also happy that it is compatible with 78 revolutions. There is a thread on the dust cover on the exterior (Satoshi Yonejima)
Maintenance information: 2024.5.12 Operation confirmed.
Accessories: power cord, connection cord, EP adapter, weight sold separately, original box
Main Specifications: Direct Drive Turntable System Brushless DC Motor Speed 33 1/3, 45, 78 Universal S-shaped Tone Arm Static Balance Needle Pressure Adjustment Range 0 to 4 g Applicable Cartridge Weight/5.6 to 12.0 g, 14.3 to 20.7 g (including headshell) /when using auxiliary weight/10.0 to 16.4 g, 18.7 to 25.1 g (headshell included) W453 mm x H173 mm x D372 mm approx. 11.5 kg
The price has been reduced! 2024/5/14 sales price 55,000 yen direct drive analog turntable. Equipped with a knife-edge tone arm in collaboration with SAEC. A Sumiko Oyster cartridge is also included, and it also has a built-in phono equalizer, so you can enjoy records right away. The exterior is good with no noticeable scratches. Serial 2280200 (Fujisawa Yukishi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: instruction manual, AC adapter, connection cord, cartridge, head shell, original box
Main specifications: direct drive aluminum die-cast static balance type S-shaped tone arm length 223 mm needle pressure variable range 0 g to 5.0 g applicable cartridge mass 3.0 g to 12.0 g, 14 g to 23 g (including attached headshell) cartridge part: mm type output voltage 4.0 mV needle pressure 1.5 to 2.5 g mass 5.3 g analog output terminal: RCA pin jack (phono/line switching type) W420 x H117 x D356 mm Weight approx. 6.1 kg
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
The price has been reduced. 2024/5/12 sales price 99,800 yen It has a well-balanced connection between all bands and a good sense of localization, and the three-dimensional grasp of sound is simple and can be reproduced with high quality. I think the AV settings are good along with the other Platinum series, but I think you can enjoy it regardless of genre even with 2CH as it is. There are 2 dents on the exterior and top plate, and a feeling of use can be seen such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.10 Operation confirmed
Accessories: zipper cross grill
Main Specifications: Input 20-150W Allowable Input (RMS) 75W Maximum Allowable Input (Instantaneous) 300W Efficiency 87dB (1W/1m) Impedance 8Ω Frequency Characteristics 40Hz to 20kHz (-6dB) LF (Woofer) 165 mm (6.5 inch), Multi-fiber Paper Cone MF (Mid) 165 mm (6.5 inch) HF (Tweeter) 25.4 mm (1 inch) Silk Dome Tweeter Crossover Type 3 Way, low loss passive type, hardwired crossover frequency 350Hz, 2.5kHz enclosure type bass reflex W235×H1,078×D300mm 17.1 kg
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
Maintained! A hit model during the heyday of audio by Sony. It has a relaxed, thick tone that you won't get tired of listening to, and it faithfully expresses the sauce without unnecessary seasoning. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 212487 (Hiroki Aso)
Maintenance information: 2024.4.26 maintained (MUT switch, push slide, SW exchange, volume VR, sound replacement, speaker relay due to deterioration, 14 parts replacement, other input selector, cartridge selector, each SW disassembly contact, polishing grease application, etc., DC bias balance adjustment, each input/output sound output check)
Accessories: copy of instruction manual
Main specifications: 105W+105W (8Ω) PHONO MM/MC (40Ω/3Ω) W430 × H161 × D436 mm 19.6 kg
A record player equipped with a Bluetooth (R) function and a USB output terminal. It can be connected to a Bluetooth (R) compatible wireless speaker, etc., and is recommended for those who want to enjoy a record player casually. As for the exterior, there is a thread on the dust cover. Serial 1007740 (Tamura Eiji)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: AC adapter, EP adapter
Main specifications: W516 × H198 × D433m mass 5 kg
It's a small digital interface that fits in the palm of your hand. The input uses a Type-C USB interface. The output is I2S/optical/coaxial. The sampling rate is PCM32 bit/768 kHz compatible, DSD native, DOP64 compatible (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: original box, connection cable
Main specifications: W80 x H13 x D60 mm dead weight 120 g
※The wood cabinet is being repaired. Maintained! This is a full set that combines 33 QUAD original transistor preamps and 303 power amplifiers with tuner FM3. Comes with a wood case that allows 33 and FM3 to be built in parallel. The impression is that the natural atmosphere has definitely increased, and the glossy way it rides and the sound that goes through the core make you think it's a vacuum tube amplifier (Oikawa Tetsuji)
Maintenance information: 2024.5.4 maintained (internal check, power supply, filter C, HPX circuit C, etc., there are many differences in capacity → replacement f cover misalignment → readjust, tuning indicator lamp back change, DIN SP-RCA female cable damaged → created)
Accessories: power cable, connection cable (2 types: DIN-RCA and DIN-DIN types), copy of the instruction manual, FM coaxial connector
Main specifications: external dimensions W550 x H113 x D220 mm, weight approx. 7.0 kg (actual measurement) [33] 3 input/line systems, 1 phono system (MM) [FM3] tubular FM dedicated tuner with automatic stereo/mono switching
Maintained! A classic British Quad stereo power amplifier. Small in size yet full torque. The sound, which is as deep as a tube amp, exudes an appeal that won't fade. The exterior has a feeling of use over time, such as dullness and small scratches. Serial 62226 (Yonejima Satoshi)
Maintenance Information: 2024.3.25 Maintained (INPUT DIN 4P replacement, internal Tr, C, R all checks. DIN4P-RCA female cable created. Operation check, pattern solder processing)
Accessories: power cable, connection cable
Main specifications: 45W+45W W120×H159×D324mm 8.2 kg
The disposal price has been reduced (member prices are not applicable). 2024/2/24 sales price 118,000 yen Maintained! This is QUAD's first transistor preamp. The dark tone, with a sweet sense of humidity, is the British sound itself. The combination with the company's 303 power amplifier is also an attractive system. There is a feeling of use due to aging (Daiki Goto)
Maintenance information: 2023.10.18 Maintained (insufficient capacity of the filter C in the power supply, coupling C in each board, bypass C, etc. → all replaced. Each Vol, SW Gari → All Clean Power cord creation.)
Accessories: power cable, connection cable, copy of instruction manual
Main specifications: Phono 1 system, 3 line systems, W260 x H92 x D165 mm, 3 kg
The price has been reduced. 2024/2/14 sales price 99,800 yen Maintenance completed! A preamplifier that can be operated by a full remote control. A familiar quad tone that is natural, easy to listen to and won't get tired of. In addition to volume, left and right balance, input switching, etc., it is fully equipped with functions such as TILT (loudness like function), high pass, low pass filter (2 levels each), etc. (Oikawa Tetsuji)
Maintenance information: 2024.1.16 Maintained (NG diode disconnected due to fuse in the main unit → short circuit in the remote control wired cord connector section → replacement, operation check)
Accessories: remote control, power cable
Main specifications: full remote control control amplifier with PHONO input (mm) W321 x H80 x D255 mm 3.3 kg
The price has been drastically reduced. 2024/3/11 sales price 80,000 yen The MEDIUM/LONG knob doesn't work, so it rotates idle, but it's a specification. QUAD tubular AM tuner. It is designed to take power from QUAD 2. Also, although the meter is an overseas specification, it is a domestic band specification. ※This is a mono specification. In order to play on 2 channels, it is necessary to connect the pin jack to the RADIO 2 terminal of QUAD2 and press the MONO and STEREO switches simultaneously (Daiki Goto)
Maintenance information: 2024.3.11 Maintained (・AM antenna ASSY added/IF/RF readjusted*Other operation checked. *When tuning with TUNE, the LCD on the right edge will open. After tuning in, it is common to listen on WIDE RANGE. Also, since the LONG WAVE circuit in this model has been removed, the LONG/MEDIUM selector is invalid and the knobs are dummy.)
Accessories: antenna cable
Main specifications: W270 x H95 x D15 mm 2.6 kg (actual measurement)
Maintained! A classic British Quad stereo power amplifier. Small in size yet full torque. The sound, which is as deep as a tube amp, exudes an appeal that won't fade. There is a feeling of use such as dullness. Serial 3121 (Takasaki Atsushi)
Maintenance information: 2024.3.22 maintained (INPUT DIN4P and AC connector replacement, DIN4P-RCA x 2 (1m) creation, internal check, DC cut C, coupling C replacement, RCH offset VOL exchange, constant change in constant voltage circuit)
Accessories: copy of manual, power cord, connection cord
Main specifications: 45W+45W W120×H159×D324mm 8.2 kg
The price has been drastically reduced. 2024/4/17 sales price 128,000 yen Maintained! Quad control amplifier The famous machine 44 has been refreshed by changing the back terminal to an RCA specification that is easy to handle. It's a perfect balance between freshness and richness. When paired with speakers made in England, you can enjoy a calm, high-quality sound (Daiki Goto)
Maintenance information: 2024.4.17 maintained (internal all checks, B-filter capacitor deterioration, +- 18V drive Tr leak large, rectifier diode failure instability → replacement power SW spark killer broken → replacement. C and R checks within each board. *There is a sound leak at main volume 0. (Create 2 1.5m DIN5 cables)
Accessories: copy of instruction manual, power cable, connection cable
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321×H103×D203 mm
The disposal price has been reduced. Member discounts are not applicable. 2024/3/20 sales price 128,000 yen Maintained! Quad power amplifier. Despite its compact body, you can enjoy a smooth, thick sound. It really goes well with speakers made in England, and makes you listen to 70s analog sound with a sense of dynamism. You can see a feeling of use such as appearance, dullness, abrasions, scratches, stains, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.3.19 maintenance (DIN connector replacement, resistance in both other channels, capacitor replacement, each Tr all check)
Accessories: connection cable, power cable, instruction manual (copy)
Main specifications: 100W+100W frequency characteristics 20 to 20 kHz dimensions W341 x H115 x D195 mm weight 9 kg
The price has been reduced. 2023/6/27 sales price 15,000 yen Qables Potaan is 192 kHz compatible. It supports up to 192 kHz/24 bit via the SPDIF digital input terminal and 48 kHz/16 bit via USB. For those looking for high quality sound anywhere easily (Oikawa Tetsuji)
Maintenance Information: 2023.6.27 Operation confirmed
Accessories: connection cord, case
Main specifications: W70 x H23 x D126 mm 200 g
A compact, high CP, and easy headphone amplifier. The sound is bright and has good visibility. A well-balanced model that works well with everything from pop to rock. Serial 32741 (Fujisawa Yukishi)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: instruction manual, AC adapter
Main specifications: output 330 mw/30 ohm, 60 mw/300 ohm headphone amplifier connection, 30 ohm gain, 11 dB S/N ratio, 87 dB frequency characteristics, 30 to 20 kHz, input/output RCA, 1 system each, W103 x D127 x H38 mm, 1.40 kg
The price has been reduced! 2024/3/22 sales price 29,800 yen The tuning hole uniquely arranged on Oyaide's turntable plate thoroughly eliminates unnecessary vibrations that disrupt the record board's trace, and can also be used in combination with a stabilizer to correct the warpage of the record board and expect an appropriate trace. There are small scratches and dullness on the exterior (Tamura Eiji)
Accessories: instruction manual, original box
Main specifications: dimensions: 294 mm, thickest part: 5 mm, 670 g
Power cable 1.2m Power cable using the original precision conductor “102SSC”. A cable with a strong monitor color that clearly reproduces music. Recommended for connecting to professional audio devices. (FUJISAWA KOSHI)
Maintenance information: 2024.5.12 continuity confirmed
Accessories: original box
Maintained! MC boost transformer optimized for SPU. The sound creation that is only slightly distorted with a small transformer embodies superb music playback by connecting the SPU. There are scratches, dirt, and tape marks on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.22 maintenance (terminal adhesive fixed wiring repair, voice check)
Accessories: original box
Main specifications: input impedance 2 ohms to 3 ohms boost ratio 60 times weight 70 g
The 1.0 m XLR terminal of the digital cable uses 7N copper for both 110Ω AES/EBU core wire and shielded braided wire. Connectors are manufactured by Neutrik (Mizusaki Ryo)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: none
The 1.0 m XLR terminal of the digital cable uses 7N copper for both 110Ω AES/EBU core wire and shielded braided wire. Connectors are manufactured by Neutrik (Mizusaki Ryo)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: none
The disposal price has been reduced. Member prices are not applicable. 2023/12/10 sales price 18,000 yen USB isolator Input to USB Type-B and output from USB Type-A. USB low-speed (1.5Mbps) and full-speed (12Mbps) dedicated hubs. Please refer to the manufacturer's website for details. https://octy.co.jp/products/usb20.html ※5V power supply is not included. Please prepare separately (Oikawa Tetsuji)
Maintenance information: 2023.12.10 storefront operation confirmed (5V test power supply is supplied, and sound output operation confirmed by connecting between PC and USB DAC)
Accessories: *USB microB 5V power supply is not included. Please use your own USB adapter or the like.
Main specifications: 110mm×64mm×30mm 230g
The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg
Pair tube 6BQ5 high reliability tube made in Japan measured value 72/68 (rejection value 46) *Pairs are determined based on GM values measured with the TV-7 test machine (Kojima Yosuke)
Accessories: none