An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
Unspecified power cable 2.0m. The plug is Panasonic WF5018K, and the connector is made by Global Electronics. This cable is relatively easy to handle. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.5.5 continuity confirmed
Accessories: none
Heavyweight stone base with a thickness of 65 mm and a weight of 63 kg! Mirror finish on the whole surface! It looks good as a base for analog players, power amplifiers, and racks. There is a chip in the corner. ※The trolley is not included. We will estimate the shipping fee separately (Fujisawa Yukishi)
Accessories: none
Main specifications: W650 x H65 x D550 mm, measured 63.1 kg
The price has been drastically reduced. 2024/1/4 sales price 500 yen. Self-made audio board with unspecified details. Audio board made by wrapping cloth around the board. The board material is unknown. There is a lot of feeling of use on the exterior, scuffs, scratches, stains, torn cloth, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W460 x H40 x D350 mm 4.6 kg
The price has been reduced. 2023/11/15 Sales price 8,000 yen Center speaker stand from unknown manufacturer. It is a type that is easy to handle with wooden casters. There are threads on the exterior. (Miura Kimiya)
Accessories: No accessories
Key Specifications: W570 ✕ H225 ✕ D440mm 4kg
You can change the position of the steel rack and shelves with casters. There are many stains, scratches, and stains on the exterior (Takimoto Yutaka)
Accessories: none
Main specifications: W540 x H1355 x D680 mm 49.6 kg (actual measurement)
You can change the position of the steel rack and shelves with casters. There are many stains, scratches, and stains on the exterior (Takimoto Yutaka)
Accessories: none
Main specifications: W540 x H1355 x D680 mm 49.6 kg (actual measurement)
Only 1 bottle unopened! Unspecified XLR (male) to XLR (female) relay plug. The exterior is good (Kobayashi Hitoshi)
Maintenance information: unopened, unchecked
Accessories: none
※1 piece only (male to male) XLR cable 1.5 m interconnect cable with unknown manufacturer. There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer The terminal is male and cannot be used as a microphone. There are a few indelible writing marks left on the plug (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.17 Conductivity confirmed
Accessories: none
The large triode print sold in Japan has disappeared, but I think it was made by NEC from the structure. Measured IP value: 45 mA (the best standard IP value for this amplifier is 50 mA) with the original box ※ I checked the sound output with the test amplifier and measured the plate current value, and it has been determined that the operation is good (Kojima Yosuke)
Accessories: original box
Wood cabinet for TD-124 of unknown manufacturer. It can be equipped with an SME long arm. The exterior has scratches, threads, chips, etc. (Tamura Eiji)
Accessories: no accessories
Main Specifications: W597 ✕ H160 ✕ D445mm Weight 3.9 kg
Prices have been reduced. 2022/11/25 sales price 100,000 yen The enclosure for TA-4151A has a thickness of 40 mm and a front baffle plate thickness of 36 mm, making it heavyweight and very sturdy. The baffle opening is φ296 mm, the unit fasteners are made of wood, and the locking screws for the baffle plate are missing. The exterior has peeling veneer and stains. (TAKIMOTO Yutaka)
Accessories: None*Baffle plate locking screw missing
Main specifications: W878 x H778 x D680 mm 101 kg (actual measurement)
※There is no compatible cartridge, so it has not been checked. Synthetic diamond round needle is a replacement needle that can be used with SHARP (Optonica) record cartridges. If you use it, be sure to use it as a stock. The exterior has a feeling of use such as dullness (Jun Tamai)
Maintenance Information: 2024.4.28 Operation Unchecked
Accessories: none
Main specifications: mm needle pressure 1.5g
manufacturer unknown. It seems to be a compatible needle for portable players whose details are unknown (Hiura Katsugu)
Maintenance information: operation unconfirmed
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2023/12/16 sales price 25,000 yen ※1 bottle only. Bass reflex enclosure imitating JBL's mid-size speaker S-99Athena. The lattice grill that symbolizes old JBL is well-made. In addition to being able to see many defects in the exterior and lattice, there is a feeling of use such as dullness, abrasions, small scratches, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: woofer aperture diameter 316 mm, screw pitch (diagonal) 338 mm high range aperture diameter 134 mm, screw pitch (diagonal) 160 mm W610 x H450 x D314 mm 16.5 kg
Balance (female) to RCA (female) conversion cable 0.21m (tip to tip) pair No. 2 can be used to convert hot balance output to RCA input (Yoichi Murakoshi)
Maintenance information: 2024.5.10 continuity confirmed
Accessories: none
Unspecified XLR (male) to RCA (female) conversion plug. The exterior is good with little feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.5.10 continuity confirmed
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2024/3/1 sales price 12,000 yen. This is a heavy weight that can be used with the Pioneer PL-70L2. If you've been looking for one, why not take this opportunity? There are dull stains all over (Murakoshi Yoichi)
Accessories: none
Key Specifications: Weight 177g
An Onken (Onken) style 38cm enclosure with an impressive bass reflex lined up on both sides. It adds thickness to the low frequencies and makes full use of the umami of the sound. Originally, the ALTEC 515B is mounted, and it is an enclosure that I want to assemble with a horn system to make it sound firmly. There is quite a feeling of use such as dirt, etc., and some broken screws. (Takasaki Atsushi)
Main specifications: W800 × H1023 (including casters) × D500mm Mounting hole diameter 345mm Screw pitch (diagonal) 372mm Width between splints on the back of the front baffle 410mm (actual measurement) 79.6 kg (actual measurement)
Pair tube, PX4 equivalent tube, direct thermal triode, made in England, measured value 54/52 (rejection value 39) with white box (there is writing on the box) *The pair was judged based on the GM value measured by the testing machine TV-7 (Kojima Yosuke)
Accessories: white box
The price has been drastically reduced. 2023.9.5 sales price 8,000 yen. Set of 8 unspecified JBL speaker mount parts MA15 type. There is a feeling of use on the exterior, paint peeling, etc. (Kobayashi Hitoshi)
Accessories: none
This is a woofer mount adapter that is thought to be used to convert a 38cm unit hole to a 30cm unit. The previous owner attached it to the JBL C38 BARON. The exterior and bolt mounting part of the individual on one side are damaged, and there is a feeling of use due to dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: mounting screw pitch: outer circumference: 370 mm, inner circumference: 293 mm; caliber: 270 mm; external dimensions: W356 x H365 x D10 mm; approx. 0.4 kg
1 bottle sold CV4085/6267 compatible ball mesh shield code: 8Y5 L2B measurement value 56 (rejection value 33) all the prints with the white box have disappeared, but it was determined to be EF86 based on the structure and code ※ The measured value shows the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Sold 1 bottle 12AU7 compatible sphere smooth plate measurement value 106 (rejection value 56) The printing with the white box has almost disappeared, but it was determined that it was an ECC82 made in Yugoslavia from the structure*The measured value represents the gm value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
※There is a TELEFUNKEN ECC803S, but from the structure, it was determined that the printing is CV4004, the printing is a reprint. The plate is not a box type, only one side of the rib plate is rib plate sold per bottle ECC83/M8137 equivalent tube measurement value 44 (rejection value 32) with replacement box ※ The measured value represents the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
※There is a TELEFUNKEN ECC803S, but from the structure, it was determined that the printing was a reprint. The plate is not a box type, but only one side of the rib plate is rib plate sold per bottle ECC83/M8137 equivalent tube measurement value 36 (rejection value 32) with replacement box*The measured value represents the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
※There is a TELEFUNKEN ECC803S, but from the structure, it was determined that the printing was a reprint. The plate is not a box type, only one side of the rib plate is rib plate sold per bottle ECC83/M8137 equivalent tube measurement value 38 (rejection value 32) with replacement box ※ The measured value represents the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
※There is a TELEFUNKEN ECC803S, but from the structure, it was determined that the printing is CV4004, the printing is a reprint. The plate is not a box type, only one side of the rib plate is rib plate sold per bottle ECC83/M8137 equivalent tube measurement value 42 (rejection value 32) with replacement box ※ The measured value represents the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
The price has been reduced! 2024/2/8 sales price 1,000 yen Compatible replacement needle for AUREX MM cartridge C-550/2. The standard needle is a carbon fiber cantilever, which is presumably made of metal. Sound was made using C-550/2 (Takahashi Nobuyuki)
Maintenance information: 2024.2.8 operation confirmed (sound output on C-550/2)
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2023/129/7 sales price 5,000 yen. 1 piece only. Phase plug for B&W 800 series. It is probably thought to be machined stainless steel, but details are unknown. How about for those looking for a center speaker such as HTM1 (Murakoshi Yoichi)
Accessories: none
Main specifications: 223g/1 piece