Beautiful item with original box! An introductory model of an MC cartridge equipped with an oval needle bonded to an aluminum cantilever. It features delicate, clear, and highly transparent expressions. (FUJISAWA KOSHI)
Maintenance information: 2024.6.2 operation confirmed
Accessories: instruction manual, original box, needle cover
Main specifications: Playback frequency range 20 to 30,000 Hz output voltage 0.32 mV needle pressure 1.8 to 2.2 g (2.0 g standard) coil impedance 12 ohms recommended load resistance 100 ohms or more (when connected to a head amplifier) stylus joint oval needle aluminum pipe cantilever mass 7.6 g
Maintained! A premain amplifier boasting high driving power, supported by a strong power supply unit typical of Sansui. The sound is soft and transparent, yet also has firm, thick bass. The sophisticated design is also attractive. There is rust on the exterior and back of the top plate, and a feeling of use such as dullness and abrasions can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.6.2 maintained (output relay, headphone relay replacement, recouped wire switch due to damage, input selector, etc., switch disassembly polishing grease application (tone, loudness, subsonic, processor, power amplifier direct, source direct, tape, reckout switch), solder repair, each volume, switch cleaning, interior and exterior inspection cleaning, adjustment inspection)
Accessories: none
Main specifications: 130W+130W (8Ω) rated power consumption 330W W471 x H162 x D452 mm weight 23.5 kg
Output transparent sale push pull output 35W primary: 8kΩ secondary: 4-8-16Ω usage: 7189 app, etc. W82 x H72 x D82 mm approx. 1.6 kg/piece (actual measurement, not including protrusions) The plate is often scratched, printing is erased a lot, and there are paint floats due to rust in places (Kojima Yosuke)
Accessories: none
The price has been reduced. 2024/4/24 sales price 69,800 yen ※Since the digital input circuit module cannot be repaired, the digital input cannot be used. Maintained! Kenwood pre-main amplifier. It plays clear, transparent mid-high frequencies and low frequencies with a firm sense of power typical of Kenwood in a well-balanced manner. There is an air cap mark on the top of the front panel. (KOBAYASHI Hitoshi)
Maintenance information: 2024.4.24 Maintained (input board connector correction, switch correction, contact correction, operation confirmation) 2023.5.21 Maintained (display lamp replacement. Switch and volume contact correction. (*The digital circuit module is broken, but the digital input cannot be used because it is not available)
Accessories: none
Main specifications: 150W+150W (8Ω) phonomC/mm mounted damping factor 1000 W 476 x H170 x D424 mm 19.7 kg
Output transparent pair for push-pull output 40W primary: 10 kΩ secondary: 4-8-16 ohms Usage: VT-62, VT-25, 6F6, 6V6, etc. W83 x H105 x D78 mm approx. 2.3 kg/piece (actual measurement, not including protrusions) with original box with scuffs and tape marks in places (Kojima Yosuke)
Accessories: original box
Output transparent pair for push-pull output 40W primary: 8kΩ secondary: 4-8-16 ohms W83 x H104 x D78 mm 2.3 kg/piece with original box (no label on one side) There are scuffs and line scratches in places (Kojima Yosuke)
Accessories: original box
Input transparent sale primary: 10 KΩ secondary: 60 kΩ boost ratio 1:2.5 W 24 x H35 mm 60 g/piece (actual measurement, not including protrusions) with white box (Kojima Yosuke)
Accessories: white box
*The attenuator is cheap and is sold as is. This model was measured to improve the quality of the NS-500M. Carbon is used for the woofer. It has a transparent tone typical of Yamaha, has good response, and is made with digital sources in mind. Overall, there is a lot of feeling of use such as small scratches and dullness (Murakoshi Yoichi)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: saran net
Main specifications: 3-way speaker 40Hz-20000Hz 6Ω 100W W374 x H678 x D324.5mm 23.5 kg
Output transparent sale Orient core output 38W for push pull applications: 6CA7, 6GB8, etc. Primary: 5 kΩ Secondary: 4-6-8-10-16 Ω W118 × H104 × D118 mm approx. 4.5 kg/piece (actual measurement, not including protrusions) There are abrasions and stains in places (Kojima Yosuke)
Accessories: none