In January 2023, both the interior and exterior were maintained and brushed up! ORIGINAL LANSALOY EDGE! The OLYMPUS S8R representing JBL has arrived. The 075 tweeter is full of realism, with the sound of a driver blowing fire into the thick, dry low frequencies, and a sense of realism that leaves graininess. You can enjoy the real thrill of vintage audio. Outside of the exterior, the back plate on one side is missing, and the finish is beautiful due to maintenance (Kobayashi Hitoshi)
Maintenance information: 2023.1.10 maintenance (exterior repair, polishing, baffle/hakama repair before and after oil finishing, painting, lattice repair, polishing, painting, lining replacement. Woofer maintenance (edge softening treatment, corn paper coating, passive corn paper coating). Driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound-absorbing material replacement, terminal contact cleaning). Tweeter maintenance (horn disassembly/polishing, magnetic circuit rust removal/gap cleaning, terminal contact cleaning). Network maintenance (LX5: terminal rust removal, acid washing, insulation bush & mounting screw replacement. ATT (SW type) disassembly contact polishing and cleaning. Reinforced with silicone to prevent the coil from coming off A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. N7000 terminal rust removal, acid cleaning, insulation bush, and mounting screw replacement. ATT replacement with a brand new one. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check input/output waveform and balance, check sound output))
Accessories: saran net, diffuser, instruction manual
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1020 x H670 x D510 mm weight 82 kg
The price has been drastically reduced. 2024/5/6 sales price 798,000 yen Strings adjusted in 2023/12. As you can see from its appearance, the stringed instruments and vocals are fascinating when you listen to them with their glossy and vivid playback sounds. Once the settings are decided, the sound image pops up in front of you, making you feel a unique sound. If you play with an amplifier with high torque, you can enjoy sound with a sense of scale that exceeds its size. There are several white line scratches on the exterior and side of the main body, but it is an individual with relatively little turbidity. Also, white stains are scattered on the side of the stand on one side. Serial 1659 (Mizushima Itsuro)
Maintenance information: 2023.12.7 maintenance (string adjustment)
Accessories: instruction manual
Main specifications: 2-way 2-speaker bass reflex 8Ω 88dB W190 x H380 (H890 stand part) x D375 mm weight 13.5 kg (stand part 36 kg)
Genuine RF Enterprise with side panels Equipped with Philips CDM4PRO, this player is easy to operate, has plenty of professional features, and excellent durability. It has a thick, supple sound reminiscent of a record, and the intensity of the mid-range is outstanding among many CD players. There are no visible scratches on the exterior, etc., and it can be said that it is good over time (Kobayashi Hitoshi)
Maintenance information: 2014.6.12 maintained (back UP battery fluid leak, poor insulation → battery removal, insulation treatment, supercapacitor replacement, other analog part bypass C, coupling C replacement, front button all dismantling, contact all polishing, operation check)
Accessories: instruction manual, power cord
Main specifications: CDM4PRO mechanical analog output 2 systems (RCA/XLR), 1 digital output system (AES), 1 clock system (BNC) W320 x H131 x D355 mm 6.1 kg
The price has been drastically reduced. 2024/5/10 sales price 468,000 yen Maintained! By installing a double 10-inch (25cm) diameter woofer while equipped with a traditional JBL horn and compression driver, a slim tall boy style is achieved with sufficient low frequency energy. It is an excellent speaker that combines low frequencies with instantaneous power typical of JBL and sharp mid-high frequencies. The exterior is good with no noticeable scratches (Shota Sasaki)
Maintenance information: 2024.5.10 Maintained (magnetic fluid removal/cleaning/center adjustment in the single-sided driver magnetic circuit gap)
Accessories: none
Main specifications: 3-way 4-speaker woofer 100FE-12 scoker 175Nd-3 tweeter 139 Nd playback frequency band 33 Hz to 40 kHz crossover frequency 850 Hz/12 kHz impedance 6 Ω output sound pressure level 92 dB allowable input 250W (RMS) W370 x H1,007 x D368 mm 39 kg
It has been refreshed and maintained to brush up by replacing block capacitors, etc.! Kit version of the masterpiece model 7. The parts that can be obtained at the beginning of sale remain the original, and those that are missing use similar parts, and it is a 25th anniversary model that appeared with almost the same structure as the original. As a vacuum tube preamp, you can hear a slightly different tone from other models. There are line scratches on the wood case on the exterior. Serial F030105 (Murakoshi Yoichi)
Maintenance information: 2024.5.9 maintenance (main volume disassembly cleaning repair, selector disassembly contact strengthening repair, block capacitor, fuse holder cap replacement, short pin addition, vacuum tube socket and RCA jack re-caulking repair. Operation has been checked with AC100V) In order to bring the volume curve closer to the original, the OUT LEVEL on the back is narrowed down. 2018.7.15 Maintained (vacuum tubes 12AX7 x 2 replaced, oil capacitors 0.47 μF replaced with BlackBeauty, replaced with 0.33 μF x 2 film capacitors. RCA jack earth reinforcement and caulk repair. Vacuum tube socket caulk repair. Other operations have been checked)
Accessories: none
Main specifications: kit model 12AX7 × 6 W453 × H185 × D260 mm 7.9 kg
The price has been drastically reduced. 2024/4/25 sales price 448,000 yen Maintenance is being carried out in 2020. It's a famous machine you can't miss when talking about Marantz sounds of yesteryear. It has a good mid-range fat transfer, and its pleasant sound is an appeal that cannot be obtained anywhere else. You can enjoy the Marantz sounds of the good times. There is some rust and small scratches on the exterior. Serial 8-4160 (Murakoshi Yoichi)
Maintenance information: 2020.11.18 maintained (AC code deterioration replacement, 40/40/20 μF and other deterioration replacement, 3 external paint, 20 μF x 2 deterioration replacement, selenium deterioration countermeasures → diode addition · vacuum tube 6BH6 noise exchange · vacuum tube socket and RCA jack caulking repair ※ other operation checked (measured at 32 to 41 W SP: 8 Ω with rated output AC 100 to 117 V) *A2 The EL34 vacuum tube guide pin is broken, but there is no problem with performance. (Part of the SP terminal on the right channel is missing.)
Accessories: instruction manual (for replicas, Japanese copy)
Main specifications: 35W+35W vacuum tube 6CG7/6BH6/EL34 W348 × H191 × D273mm 22.5 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/4/2 sales price 448,000 yen This is a late C20 model that underwent full maintenance from the 2023/12 condenser to main VOL replacement. Among Mackin's control amplifiers, this is a popular gem with a particularly rich, glossy tone. Not only jazz, but also the vocal sounds are excellent. The unique, rich, and highly artistic tone shows a particularly good compatibility with vintage speakers. Exterior, front panel characters disappear a lot, dullness, small scratches, abrasions, etc., and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.2 maintenance completed (1/2 W resistor replacement and 3 noise countermeasures replaced) 2023.12.19 maintenance (vacuum tube 6X4, block capacitor, electrolytic capacitor, film capacitor, oil capacitor, resistor, main volume replacement. Gang error correction resistance 1/2 W added, switching noise reduction resistance 1/4 W added. RCA jack and vacuum tube socket caulk repair, operation check.)
Accessories: none
Main specifications: tubular phono 2 system phono equalizer curve variable use vacuum tube ECC83 x 5 ECC82 x 2 EZ90 x 1 W440 x H165 x D316 mm 8.7 kg
The price has been reduced. 2024/5/19 sales price 298,000 yen The successor to the company's Aleph 0s. Pure Class A amplification operation. The power supply unit has been changed and the non-feedback circuit follows the previous model. Similar to the 0s, the richness and elasticity of the Nelson Pastune has the impression that the number of sounds has increased while retaining it, making it compatible with various genres. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 sound output confirmed
Accessories: instruction manual, power cord, original box
Main specifications: execution output 60W+60W (8Ω) input impedance 25kΩ (balance) 10kΩ (unbalanced) W304 × H267 × D305 mm 20.4 kg
Maintained! The strength of the extrusion of the entire range and the clear sound are truly sounds unique to the heyday of JBL. The mid-high range with a unique sense of spaciousness and strong linearity makes hard bop and trumpet sounds pleasant. The sense of volume in the mid to low range is also attractive not found in modern speakers. The exterior has been beautifully finished due to maintenance (Mizusaki Ryo)
Maintenance information: 2024.5.11 maintained (exterior repair/polishing/oil finish, front and rear baffle/horn repair/painting, saran net replacement/frame repair, woofer edge replacement, driver maintenance: magnetic circuit rust removal/gap cleaning/center adjustment, network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/screw replacement, unit detachment)
Accessories: saran net
Main specifications: 2-way bass reflex, 30cm woofer, frequency band, 40Hz to 16kHz, impedance, 8Ω, sound pressure level, 91 dB, dimensions W406 x H635 x D311 mm, weight 26 kg/book
Maintained by the manufacturer. It has an aspect as an entry model, but it is a model where you can fully enjoy the uniqueness of Accuphase. In addition to the wide range, it is supple and has a slight sex appeal, so you can enjoy it for 12 minutes. A powerful unit that sounds regardless of whether it is a large or medium speaker. In addition to conspicuous marks on the exterior and top plate, a feeling of use such as dullness, stains, and threads can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.17 manufacturer maintenance (push switch, volume, etc., cleaning, parts replacement, decorative plate installation, inspection of each part, adjustment, safety check, pressure resistance check)
Accessories: power cable, remote control, manual
Main specifications: 100W+100W (8Ω) parallel push-pull output stage current feedback amplifier circuit W475×H170×D424mm 21.4 kg
Internally and externally maintained! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. There is a very slight dent in the tweeter grill, and there are repair marks on the side (Murakoshi Yoichi)
Maintenance information: 2024.3.4 maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network frequency characteristic check, ATT cleaning, terminal replacement)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
This is a standard JBL monitor that has undergone internal and external maintenance and has been refreshed. The darker and thicker tone compared to the current model still doesn't even seem to be declining in popularity. The thick, exhilarating sound goes well with jazz and rock, and the punchy sound is captivating. The exterior has been beautifully finished due to maintenance. Serial 32547 32298 (Murakoshi Yoichi)
Maintenance information: 2024.5.16 maintenance (exterior repair/cleaning, saran net cleaning, repasting, ATT cleaning)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system frequency characteristics 45 Hz to 20 kHz sound pressure level 93 dB impedance 8 ohms allowable input 100 W dimensions W362 x H597 x D298 mm weight 20 kg/1
Maintained in 2023. After all, the warm, and glossy sound quality is excellent for stringed instruments. It has a soft and vivid sound not found in transistors, making it perfect for listening for long periods of time. In addition to noticeable scuffs and paint peeling on the exterior and transformer area, dullness and a feeling of use can be seen. Serial F0800283 (Murakoshi Yoichi)
Maintenance information: 2023.7.23 maintained (vacuum tube socket block capacitor electrolytic capacitor oil capacitor SP and RCA terminal semi-fixed VR fuse holder replacement load test (8Ω load 1kHz 25W+25W) input/output waveform confirmation sound output check performed gain VOL NFB switching SW disassembly contact refinement to prevent oxidation and sulfation grease coating input/output waveform confirmation distortion load test (1 kHz (25W+25W at sine wave 8Ω load) sound output test)
Accessories: copy of instruction manual
Main specifications: 50CA10 push-pull output 30W+30W W410 x H183 x H160 mm 13.8 kg
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
The A3500 vacuum tube power amplifier has been refreshed by thorough maintenance down to the smallest details, such as volume disassembly and polishing. The warm, fresh tone, filled with the appeal of a vacuum tube type, is still appealing enough today. You can enjoy music with a rich, thick tone that contrasts with the clicking tones of recent vacuum tube amplifiers. As for the exterior, paint deterioration and peeling can be seen on the transformer on one side, and there is a feeling of use such as dullness, small scratches, etc., and there is a dent in the hood. ※3-pole tube connection specification. 20W+20W (actual measurement) is output as specified by the manufacturer (Takasaki Atsushi)
Maintenance information: 2023.2.3 maintained (main tube (6CA7) replacement vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, complete disassembly of semi-fixed VR replacement power input gain volume, contact polishing, anti-oxidation/sulfation grease coating load test (8Ω load 1kHz 20W+20W) input/output waveform confirmation sound output check performed)
Accessories: copy of the manual
Main specifications: 20W+20W (8Ω) vacuum tube 6CA7×4/6AQ8×3 W465×H168×D206mm 16kg
The price has been reduced. 2024/5/19 sales price 148,000 yen A typical woofer attached to first-class products such as Exclusive2402 and Westlake Audio. It is a highly stable model that can withstand professional use. The response speed is fast and the sound that makes it stand up well is attractive. There is a light stain on the corn paper (Murakoshi Yoichi)
Maintenance information: 2024.5.17 sound output confirmed
Accessories: none
Main specifications: 40cm cone woofer frequency characteristics 28 Hz to 1000 Hz 8 ohms (measured 7.9 ohms) output sound pressure level 97 dB dimensions diameter 400 mm x depth 167 mm 11 kg/1
Maintained! A prime amplifier developed during the heyday of CDs and gained popularity. The powerful, punchy sound quality, which combines the quality of the mid-high range with the power of the low frequencies, is attractive. There is room not found in lower models, and you can enjoy the sound with a sense of scale typical of SANSUI. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 maintenance completed (tone and other switch disassembly polishing grease application (loudness, turnover, subsonic, muting, processor, input selector, power amplifier direct, source direct, tape, reckout switch), output relay, headphone relay replacement, power supply transistor replacement, power amplifier circuit transistor replacement, resistor, adjustment volume replacement, solder repair , interior and exterior inspection and cleaning, bias, DC adjustment, confirmation of each input/output, operation inspection)
Accessories: copy of instruction manual
Main specifications: Advanced α-X circuit equipped with 160W+160W (8Ω) damping factor 150 (8Ω) Phonomm/MC compatible W460 x H159 x D446 mm weight 33 kg
The price has been drastically reduced. 2024/5/17 sales price 148,000 yen B&W middle class “tweeter on top” model from the new commercial series. You can enjoy high-response sounds and vivid and realistic spatial expressions. There is a large dent on one side and side, and there is a light feeling of use and dullness (Murakoshi Yoichi)
Maintenance information: 2024.5.16 sound output confirmed
Accessories: saran net, instruction manual
Main specifications: 8Ω 88dB 45Hz to 50kHz W200 × H403 × D301 mm weight 8.9 kg
The price has been reduced. 2024/5/4 sales price 128,000 yen*Inexpensive because Saran Net is out of stock. Infiniti's best-selling speaker. It's a 3-way system that brings out quite a bit of volume for a tall boy type. The bass is also sufficiently reproducible with a sense of scale coming out of the double woofer, and even pipe organs can be reproduced with plenty of room. You can see a feeling of use on the exterior, dullness, stains, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2023.6.7 operation confirmed
Accessories: copy of instruction manual, jumper, spike
Main specifications: 3-way system frequency characteristics 35 to 450,000 Hz crossover 250/3,500 Hz 6 ohms W390 × H1200 × D380 mm 40 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/5/17 sales price 128,000 yen ※Depending on the arm base, the mounting position of the arm is slightly close to the shaft side. Since the arm is long, please remove the dust cover for playback. Comes with SAEC arm stabilizer AS-500! A record player that is highly regarded for its smooth rotation and the effectiveness of the insulator's suspension. The WE-308 arm features a double knife edge for sharp sound and accurate sound image localization. It is a combination of LUX's smooth and quiet motor and SAEC arms that cut sharply into the sound source, so you can fully enjoy the fun and depth of analog. Additional rubber feet have been attached to the legs to prevent AS-500E. The exterior is dull and has small scratches. Serial G8903281 (Murakoshi Yoichi)
Maintenance Information: 2020.6.2 Maintained (created with strobe circuit LED. diode installation. Electrolytic capacitor replacement. Power circuit film capacitor replacement. (Inside Force cancellation weight exchange)
Accessories: phono cable
Main specifications: PD-131 direct drive system 8 pole 24 slot brushless DC servo motor W472 x H160 x D372 mm weight 12 kg WE-308 double knife edge static balance universal type total length 329 mm effective length 240 mm overhang 5 mm needle pressure 0 to 2 g cartridge weight range: 5.5 to 12.5 g
The price has been drastically reduced. 2024/5/9 sales price 128,000 yen Maintained in 2023/10! Late QUAD44 with CD input terminal. It's not flashy, but the thick, glossy tone is attractive. In particular, it softens female vocals. The exterior has a feeling of use such as dullness and small scratches. Serial Q031658 (Murakoshi Yoichi)
Maintenance information: 2023.10.22 Maintained (Acre sectorable terminal caulking defect? → soldering. Balance Vol, Filter Vol, SW Cleaning AC spark killer NG, internal in-board bypass C, coupling C replacement)
Accessories: instruction manual, power cord, catalog (English)
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321×H103×D203 mm
The disposal price has been reduced. Member discounts are not applicable. 2024/4/9 sales price 138,000 yen ※It is cheap because the condition is not good. Next-generation model of the L-550, a famous pure Class A amplifier that has been maintained by the manufacturer (*PHONO1 cannot be used due to a broken equalizer board). The very smooth, deafening warm color sound perfectly matches the delicate sound quality of pure A grade. It also has a reputation for analog sound, and thick sound quality can be obtained with both MM/MC. There is a feeling of use due to appearance, dullness, abrasions, scratches, paint deterioration, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.9 manufacturer maintenance completed (equalizer selector switch disassembly cleaning, correction due to broken equalizer board, other contact cleaning, general adjustment*PHONO1 cannot be used due to broken equalizer board)
Accessories: copy of instruction manual
Main specifications: pure A grade 50W+50W (8Ω) PHONO (MM/MC) PHONO/CD straight circuit system W453 x H174 x D470 mm weight 20 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg
Maintained! A classic British Quad stereo power amplifier. Small in size yet full torque. The sound, which is as deep as a tube amp, exudes an appeal that won't fade. There is a feeling of use such as dullness. Serial 3121 (Takasaki Atsushi)
Maintenance information: 2024.3.22 maintained (INPUT DIN4P and AC connector replacement, DIN4P-RCA x 2 (1m) creation, internal check, DC cut C, coupling C replacement, RCH offset VOL exchange, constant change in constant voltage circuit)
Accessories: copy of manual, power cord, connection cord
Main specifications: 45W+45W W120×H159×D324mm 8.2 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/3/20 sales price 128,000 yen Maintained! Quad power amplifier. Despite its compact body, you can enjoy a smooth, thick sound. It really goes well with speakers made in England, and makes you listen to 70s analog sound with a sense of dynamism. You can see a feeling of use such as appearance, dullness, abrasions, scratches, stains, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.3.19 maintenance (DIN connector replacement, resistance in both other channels, capacitor replacement, each Tr all check)
Accessories: connection cable, power cable, instruction manual (copy)
Main specifications: 100W+100W frequency characteristics 20 to 20 kHz dimensions W341 x H115 x D195 mm weight 9 kg
Maintained! A popular DENON control amplifier for its excellent phono equalizer. MC head amplifiers are famous for their quality, and they fully draw out the amount of information in the cartridge. It's a neat sound typical of a domestic amplifier with clear yet solid mid-range sound. In addition to the exterior, noticeable scuffs on the top plate, scratches on the VOL dial, and stains on the back of the front flap, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.2.16 Maintained (main volume, balance volume internal contact cleaning, cleaning. All input terminals are polished and cleaned, electrolytic capacitor replaced, PHONO2 impedance changeover switch disassembly, contact polishing, cleaning, and grease is applied. (Check the operation of each input/output)
Accessories: instruction manual (copy)
Main specifications: CR equalizer with 3 PHONO inputs MC head amplifier W455 x H132 x D357 mm 10.5 kg
The price has been reduced. 2024/4/29 sales price 110,000 yen The 3 channel 5 units are nicely put together in one package. In addition to the fact that a rich sound field can be simply played back via Bluetooth, etc., it is a product with an emphasis on functionality that can also be enjoyed with analog. Recommended for studio users. Other than the exterior and stains on the top plate, it's fine (Kobayashi Hitoshi)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: remote control, power cord
Main specifications: 33mm pure pulp cone woofer x 2, 25mm aluminum dome tweeter x 2, 100mm pure pulp cone center midrange x 1 input HDMI (ARC), 3.5mmAUX, RCA Phono (MM), Ethernet/WiFi Bluetooth playback frequency characteristics 45Hz to 25kHz (-6dB) W790 x H216 x D287mm 15.9 kg
The disposal price has been reduced. Member prices are not applicable. 2024/3/7 sales price 128,000 yen Maintained! A crisp, bright, and sharp sound typical of Marantz from the 1970s. Exactly, it's an American sound on the west coast. The design is also a simple design typical of US Marantz. ※The leg is out of stock. The exterior has dullness and small scratches. Serial 4180 (Yonejima Satoshi)
Maintenance information: 2024.3.7 Maintained (single CH power stage transistor replacement. Screwdriver transistor resistor replacement. Drive Tr Capacitor Replacement Contact polishing, aging test)
Accessories: No accessories
Main specifications: 125W+125W (8Ω) W445 × H170 × D265 mm 14.8 kg
The price has been reduced. 2024/5/10 sales price 99,800 yen Maintained. professional monitor amplifier It has strength unique to commercial use, and the driving power in the low range is truly remarkable. However, it also has a strong sense of temperature typical of a quad, so it is an amplifier that I would like people who are shunned when the sound is too straight for commercial use to try it once. There is a feeling of use such as a scuff on the top plate. Serial Q002959 (Mizushima Itsuro)
Maintenance information: 2024.2.15 maintenance (internal Tr, C, R check, output phase correction resistor, DC IN± bypass C, gain setting C, CDS replacement within the INPUT photocoupler. INPUT VOL CLEANING Output cable XLR cannon attached)
Accessories: copy of instruction manual, power cable, speaker cable
Main specifications: 100W+100W (8Ω) W483 × H88 × D310 mm 12.5 kg
The Philips CD-16 swing-arm CD-16 player with CDM4 is now in stock. The Marantz sound has an attractive transparent, supple sound. You can comfortably enjoy classical music, vocals, etc. just like analog music. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: remote control, instruction manual, transport lock pin
Main specifications: analog output, RCA1 system, digital output, 2 coaxial systems, W458 x H110 x D369 mm, 11 kg
Maintained by the manufacturer! A special edition model of VRDS-10. This is the only TEAC player model that uses a Philips TDA1547 as a D/A converter. The sound quality is not sharp due to the hardware of VRDS, and the sound quality is well-balanced, which brings out the characteristics of the relaxed DAC7. In addition to being able to see many scratches on the exterior and top plate and abrasions on the front panel, there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 manufacturer maintained (flat cable adjustment) 2024.4.13 manufacturer maintained (belt replacement, deteriorated parts replacement, inspection and adjustment of various parts)
Accessories: remote control, copy of instruction manual, lock key
Main specifications: 2-channel CD player frequency characteristics 1 Hz to 20 kHz 8 times oversampling 20 bit digital filter W442 x H149 x D331 mm 11 kg
The price has been drastically reduced. 2024/3/2 sales price 99,800 yen Maintained! professional monitor amplifier It has strength unique to commercial use, and the driving power in the low range is truly remarkable. However, it also has a strong sense of temperature typical of a quad, so it is an amplifier that I would like people who are shunned when the sound is too straight for commercial use to try it once. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.3.2 maintained (internal dismantling all check, Tr, C, R check, ±B INPUT bypass C replacement, Tr, R, etc., all OK, INPUT photocoupler check, operation check)
Accessories: copy of instruction manual, power cord, dedicated SP cord (cable length 2.5 m)
Main specifications: 100W+100W (8Ω) W483 × H88 × D310 mm 12.5 kg
Maintained! 15th anniversary model of the 607 series. MOS-FET is used for the power stage, adding a sense of transparency to its characteristic heat, and is compatible with various music genres. It has a configuration that exceeds its class, such as balanced input support, and it is a powerful machine that is still popular today. You can see a feeling of use, such as appearance, dullness, small scratches, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 maintenance completed (tone and other switches dismantled and polished, coated with grease (loudness, muting, processor, subsonic, input selector, power amplifier direct, source direct switch), output relay replacement, protector part capacitor replacement, solder repair, internal inspection and cleaning, bottom repair, operation confirmation)
Accessories: power cable, copy of manual
Main specifications: 45W+45W (8Ω) PHONO (MM/MC) W460 × H159 × D446mm 18.8 kg
*Needle cover is missing. Elliptical type with built-in step-up transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior has small scratches, dullness, and a feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.5.17 sound output confirmed
Accessories: none
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
Maintained in 2015. The 606 is thick and unimaginable from its compact exterior. The good sound unique to QUAD allows you to enjoy not only classical music, but also jazz vocals in a mild way. The high level of musicality that makes you enjoy the music with a pleasant tone stands out. There is deterioration in exterior paint (Murakoshi Yoichi)
Maintenance information: 2015.9.12 maintenance completed (internal power transfer → malt plane deterioration → dismantling and reinstallation, exchange of both channel in-board bypass C, gain setting C, etc., TR check → OK, operation inspection check)
Accessories: power cord
Main specifications: output 140W+140W (8Ω) W321×H140×D238mm 12kg
The price has been drastically reduced. 2024/2/18 Marantz pre-main amplifier with sales price 89,800 yen. The preamp circuit has been revamped to enhance spatial expression ability and detail reproducibility. Similar to the PM-10 and PM-14S1, a highly accurate electronically controlled volume is used for the volume circuit. It makes it possible to reproduce bass that combines a sense of scale and instantaneous power. Serial AWY15180500756 There are scratches on the top plate on the exterior (Hiura Katsuji)
Maintenance information: 2024.2.18 Operation confirmed
Accessories: remote control power cable
Main specifications: 100W+100W (4Ω), 70W+70W (8Ω) frequency characteristics 5Hz-100kHz
W440×H128×D379mm 12.0kg
The price has been reduced. 2024/4/27 sales price 79,800 yen This is a 3-way center speaker with the tuning that best matches the 500, 300, and 100 of the company's Silver series. Since the C350 was designed to pursue only performance without considering size restrictions, the dynamism in terms of sound quality is impressive. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.26 Operation confirmed
Accessories: saran net, jumper (general purpose) original box
Main specifications: 3-way sealed frequency characteristics 40Hz-35,000Hz crossover frequency 830Hz/3,200Hz allowable input 200W recommended amplifier output 80-200W W560×H235×D240mm 14.9kg