Wood cabinet for TD-124 of unknown manufacturer. It can be equipped with an SME long arm. The exterior has scratches, threads, chips, etc. (Tamura Eiji)
Accessories: no accessories
Main Specifications: W597 ✕ H160 ✕ D445mm Weight 3.9 kg
The price has been reduced. 2023/11/15 Sales price 8,000 yen Center speaker stand from unknown manufacturer. It is a type that is easy to handle with wooden casters. There are threads on the exterior. (Miura Kimiya)
Accessories: No accessories
Key Specifications: W570 ✕ H225 ✕ D440mm 4kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/9 sales price 99,800 yen with wood horn! Maintained! An integrated mid-range driver unit developed for 3-way use. It's an energetic, easy-to-read sound typical of YL. Paint peeling can be seen in places. Serial 751903, 751903 (Fujisawa Yukishi)
Maintenance information: 2024.4.9 maintained (coil roundness adjustment, noise suppression, porcelain circuit slit maintenance)
Accessories: No accessories
Main specifications: Playback frequency band 800 to 8,000 Hz maximum input 40W 8Ω output sound pressure level 101 dB outer diameter W400 × H200 × D350 mm 3.30 kg
Full maintenance, such as internal and external maintenance, was carried out, and the finish was beautiful! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. Serial 55553L, 55553R (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (exterior repair/repaint) 2017.4.25 Maintained (exterior polishing/all coated woofer cone paper/unit frame paint chip putty repair grill dent correction/paint tweeter distortion and maintenance (edge deformation repair, magnetic circuit slit maintenance complete) unit detachment terminal replacement (banana plug compatible product) ATT cleaning capacitor replacement*Some capacitors before replacement Since it is difficult to remove, remove the wiring to check the remaining input/output waveform and balance, sound output check, frequency characteristic measurement check (~ 42 kHz)
Accessories: No accessories
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
The price has been reduced. 2024/3/3 sales price 15,000 yen*Currently sold. Yamaha superwoofer equipped with a 20 cm x 2 double woofer. Equipped with active servo technology and a 150W high-power amplifier, it plays bass that is small yet full of volume. There is dirt, dirt and dullness on the exterior, and some floating on the bottom. Serial Z117079QS (Tamura Eiji)
Maintenance information: 2024.3.3 sweep test is good
Accessories: No accessories
Main specifications: used unit 20 cm cone type x 2 rated output 150 W (5 Ω) playback frequency band 20 Hz to 160 Hz high cut filter 40 Hz to 140 Hz, continuously variable W235 x H602 x D463 mm 20 kg
The price has been reduced. 2024/2/24 sales price 6,000 yen ※Since it is cheap, it will be handed over as is. A subwoofer that can also be installed in a home theater or for those with insufficient bass in the system. The settings are simple, and you can create sound according to the speaker and room conditions. The exterior has some holes in creases and threads. Serial Z213158SU (Yonejima Satoshi)
Maintenance information: 2024.2.24 sweep test good
Accessories: instruction manual
Main specifications: 1 way, 1 speaker, advanced YST system, floor type, anti-magnetic high cut filter, 50 to 150 Hz, continuously variable, W235 x H485 x D409 mm, 14 kg
YAMAHA speaker stand The compact stand is made to feel stiff, and you can expect tight sound quality. It can be used for small speakers such as the NS-10M and medium speakers. There are line marks, threads, and tape marks on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: W270 x H494 x D350 mm top plate part W190 W x D175 mm 7 kg/unit
The price has been reduced. 2023/8/12 sales price 19,800 yen speaker cable 1.5m pair single (Y lug) single side (Y lag) single side tri-wire (Y lag) specification A parallel arrangement structure that neutralizes and makes the flow of electricity accurate. A high CP cable that is smooth and has a sense of speed. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2023.8.12 Conductivity confirmed
Accessories: no accessories
HDMI cable 1.0 m transmission speed 10.2 Gbps to 21 Gbps (varies depending on cable length) The shorter the cable, the faster the transmission speed. (FUJISAWA KOSHI)
Maintenance information: 2024.5.23 continuity confirmed
Accessories: No accessories
It is equipped with a 165 mm diameter woofer that uses a Kevlar woven cone that suppresses the generation of split vibrations, and is equipped with an advanced driver unit that supports rich musicality. The cabinet design is optimized using unique computer software and the latest spectrum analyzer analysis technology, and the input terminals are equipped with 2 sets of speaker terminals compatible with banana plugs. There is a small scratch on the side of the exterior. Serial WH057521BGH0025, WH057521BGH0025 (Fujisawa Yukishi)
Maintenance information: 2024.6.4 operation confirmed
Accessories: instruction manual, original box, jumper plate, saran net
Main specifications: output sound pressure level 87 dB impedance 8 ohms playback frequency band 45 Hz to 20 kHz W196 x H355 x D290 mm weight 6.5 kg
The price has been reduced! 2024/5/31 sales price 29800 yen ※6 month warranty. It is a speaker that was created with the aim of natural sound and gained popularity. There is no sense of emphasis and there is a good balance of strength between the high and low frequencies, which have a high texture, and it makes me feel the high level of musicality. There are scratches on the exterior. Serial 16400837L, 16400837R (Fujisawa Yukishi)
Maintenance information: 2024.5.31 operation confirmed
Accessories: jumper cable
Main specifications: 2-way, 2-speaker sealed, magnetic-proof type, W270 x H456 x D290 mm, 12.5 kg
Special stand for SX-311GY Chic grey finish It is a model that can be used with various medium speakers. Dullness, small scratches, and abrasions due to aging are conspicuous on the exterior. (YONEJIMA Satoshi)
Accessories: No accessories
Main specifications: W330 x H440 x D294 mm top plate part W267 x D245 mm 5.3 kg
Line transformer from Uesugi Laboratory. By sandwiching it between the digital device and the amplifier, the characteristic digital noise that causes listening fatigue is removed. You can expect a change in sound quality that is familiar to the ear. It is possible to switch between 3 types of input impedances. There are scratches on the exterior. Serial 057 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: impedance compatible with 3 RCA input systems 200 ohms: 200 ohms 500 ohms: 500 ohms W175 ✕ H150 ✕ D115mm 2.5 kg
MC boost transformer loaded with transformers developed in collaboration with Tamura, for high impedance. Adopts a completely independent structure for the left and right, including the earth system. It matches Denon's DL-103, etc. The exterior has minor paint peeling and bumps. Serial 298 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: primary impedance 40 ohms secondary impedance 4 kΩ boost ratio 10 times W174 x H125 x D121 mm 2.5 kg
※It is inexpensive because it leaves cracks in the VOL. A headphone amplifier that allows you to enjoy the sound of 2 systems: a vacuum tube and a transistor. It has a built-in USB DAC compatible with 24 bit 96 kHz, and it is a blissful item that allows you to immerse yourself in both digital and analog worlds to your heart's content. Scratches on the transformer area are slightly noticeable. Serial 12060066 (Fujisawa Yukishi)
Maintenance information: 2024.6.3 operation confirmed (sound output OK, gaps remain in VOL)
Accessories: instruction manual, power cord
Main specifications: Vacuum tube using a class single headphone amplifier 6BM8 x 2 vacuum tube output 20Ω to 600Ω (45mW to 135mW) transistor output 12Ω to 300Ω (40mW to 135mW) frequency characteristics 10Hz to 50,000 Hz SNR 89dB power consumption 30W size W190 x H150 x D250 mm mass 4.7 kg
The disposal price has been reduced! Member prices are not applicable. 2024/4/28 sales price 118,000 yen including new dust cover created and maintained! Torrens basic model. You can enjoy rich musical analog sound with the genuine TP90 straight arm. Belt drives, double platter floating suspensions, and the basics of record players that continue to continue in Europe are firmly held in place. The exterior is dull. Serial 21727 (Fujisawa Yukishi)
Maintenance information: 2024.4.28 maintenance (new dust cover created. (Rewinding the lifter lever lock solenoid coil, end detection cam processing correction, end position adjustment, belt replacement, board inspection, rotation check arm operation, voice check)
Accessories: arm adjustment strut, AC adapter
Main specifications: 50Hz/60Hz compatible W440 x H150 x D340 mm weight 11 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/5/14 Torrens entry model with sales price 118,000 yen. Although it is an entry model, the silence and smoothness of the belt drive, and the delicate sound are attractive, and the tone arm is easy to adjust. Recommended for introductory belt drive machines. There are a few small scratches on the exterior. Serial 00262803 (Fujisawa Yukishi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: copy of instruction manual, power cord, connection cord, spike base, original box
Main specifications: W420 x H125 x D330 mm 8 kg Drive system: belt drive motor: synchronous motor speed: 33 1/3, 45 rpm electronic speed selection platter: diameter 300 mm, 3 kg, aluminum power supply unit housing tone arm: static balance type
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. Serial 2172380ZGD00103 (Fujisawa Yukishi)
Maintenance information: 2024.6.2 operation confirmed
Accessories: power cord
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
The price has been reduced! 2024/5/12 sales price 148,000 yen A new standard model for the SL-1200 series that inherits the efforts and results that began with the development of the SL-1200G. Outstanding reliability and stability are now available at an affordable price. I'm also happy that it is compatible with 78 revolutions. There is a thread on the dust cover on the exterior (Satoshi Yonejima)
Maintenance information: 2024.5.12 operation confirmed
Accessories: power cord, connection cord, EP adapter, subway, original box
Main Specifications: Direct Drive Turntable System Brushless DC Motor Speed 33 1/3, 45, 78 Universal S-shaped Tone Arm Static Balance Needle Pressure Adjustment Range 0 to 4 g Applicable Cartridge Weight/5.6 to 12.0 g, 14.3 to 20.7 g (including headshell) /when using auxiliary weight/10.0 to 16.4 g, 18.7 to 25.1 g (headshell included) W453 mm x H173 mm x D372 mm approx. 11.5 kg
※Since it is cheap, it will be handed over as is. Comes with a remote control! CD-RW compatible CD recorder. This model is equipped with a TEAC high-performance CD/RW drive capable of 4x speed recording. There are small scratches on the exterior. Serial 0240023 (Yonejima Satoshi)
Maintenance information: 2024.6.5 operation confirmed
Accessories: remote control, instruction manual
Main specifications: CD-RW compatible CD recorder, 4x speed recording, finalization, 4x speed microphone, analog output (RCA), 1 system, 2 digital input/output systems each (optical/coaxial), 1 microphone input system, 1 system, W435 x H102 x D312 mm 5.5 kg
※Since it is cheap, it will be handed over as is. Comes with a remote control! CD-RW compatible CD recorder. This model is equipped with a TEAC high-performance CD/RW drive capable of 4x speed recording. There are small scratches on the exterior. Serial 0240023 (Yonejima Satoshi)
Maintenance information: 2024.6.4 operation confirmed
Accessories: remote control, instruction manual
Main specifications: CD-RW compatible CD recorder, 4x speed recording, finalization, 4x speed microphone, analog output (RCA), 1 system, 2 digital input/output systems each (optical/coaxial), 1 microphone input system, 1 system, W435 x H102 x D312 mm 5.5 kg
※ It is inexpensive because it is in poor condition such as dirt and felt peeling. Set of 3 classic TAOC basses. Made of high-carbon cast iron with excellent vibration handling capabilities. It can be used for a wide range of speakers from large to medium, and accurately reproduces sound images. The exterior has rust and dirt due to aging, and deterioration in the bottom felt (Satoshi Yonejima)
Accessories: none
Main specifications: W100×H200×D300mm 9.2 kg
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
※Since it is inexpensive, it will be handed over as is. Tamban 10cm full range unit. An ultra-thin PP diaphragm with reinforced ribs is used. The sound is clear and crisp. A 6-8 liter bass reflex box is recommended (Tamura Eiji)
Maintenance information: 2023.10.1 sweep check OK
Accessories: none
Main Specifications: Rubber Edge Impedance 4 Ohms Sound Pressure Level 87 dB Frequency Band 63 to 17,000 Hz Maximum Input 40 W Baffle Aperture Diameter 94 mm Weight 380 g
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
The disposal price has been reduced! (Member price not applicable) 2024/5/24 sales price 128,000 yen A digital amplifier equipped with a Tripath class T PWM amplifier IC. It beautifully expresses the sense of energy and description. Gain can also be switched on the back, and it is compatible with a wide range of input sources. On the exterior, there are oxidation and scratches on the manufacturer logo. Serial 100210015 (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: instruction manual, power cable, spike
Main specifications: output 150W+150W (8Ω) 240W+240W (4Ω) W420 x H98 x D395 mm weight 13 kg
Maintained! A hit model in the heyday of audio by Sony. It has a relaxed, thick tone that you won't get tired of listening to, and it faithfully expresses the sauce without unnecessary seasoning. There is a chip on the corner of the side panel. Serial 203719 (Fujisawa Yukishi)
Maintenance information: 2024.6.3 maintained (replaced with a custom-made product due to VR loud sound, speaker relay replaced, MUTIG push SW replaced, other INPUT selector SW, cartridge LOAD SW, TAPE selector SW, SW disassembly contact polishing grease applied, other DC bias DC balance adjustments, confirmation of sound output for each input/output terminal connection)
Accessories: No accessories
Main specifications: 105W+105W (8Ω) PHONO MM/MC (40Ω/3Ω) W430 × H161 × D436 mm 19.6 kg
A record player equipped with a Bluetooth (R) function and a USB output terminal. It can be connected to a Bluetooth (R) compatible wireless speaker, etc., and is recommended for those who want to enjoy a record player casually. As for the exterior, there is a thread on the dust cover. Serial 1007740 (Tamura Eiji)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: AC adapter, EP adapter
Main specifications: W516 × H198 × D433m mass 5 kg
It's a small digital interface that fits in the palm of your hand. The input uses a Type-C USB interface. The output is I2S/optical/coaxial. The sampling rate is PCM32 bit/768 kHz compatible, DSD native, DOP64 compatible (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: original box, connection cable
Main specifications: W80 x H13 x D60 mm dead weight 120 g
*The stylus is a JICO VN35HE. Good stylus and cantilever. It combines the delicate expressive power unique to light needle pressure with an energetic, thick sound typical of Type 3. Recommended for those who listen to jazz and rock. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.6.2 operation confirmed
Accessories: No accessories
Main specifications: mm type frequency range 10 Hz to 25,000 Hz output voltage 3.5 mV needle pressure 0.75 g to 1.25 g weight 6 g
Maintained! One of Sansui's few 2 to 4 way NF type channel dividers. It is a channel divider that pursues basic characteristics and multiple functions, and features a highly saturated tone that is close to JBL speakers. After adjustment, the ceiling panel is clean and the design is excellent. There are scratches and scratches on the exterior. Serial 238070032 (Fujisawa Yukishi)
Maintenance information: 2024.6.4 Maintained (mode selector disassembly contact polishing. Frequency selector x 6 disassembly cleaning Other volume cleaning. (Replace diodes and transistors to enhance power supply)
Accessories: front panel
Main specifications: 2/3/4 way NF filter channel divider with SNR 90dB or higher cutoff frequency (± 10%) [F1] 60/75/95/120/150/190/240/300/380/480/600/750/950/1.2k/1.5k/1.9k/2.4k/3kHz [F3] 1.5k/1.9k/2.4k/3k/3.8k/4.8k/6k/ 7.5K/9.5K/12K/15kHz low star function installed (turnover 60 Hz/100 Hz) W482 x H88 x D305 mm 6.4 kg
The price has been reduced! 2024/5/17 sales price 49,800 yen Maintained! Sansui's rare CD player. The firm outline and comfortable sound are attractive. I would like to use it in combination with the company's α series premain for a unified look. In addition to listening to CDs, it also has a convenient function when recording to tape, etc., and has a variety of aspects. The exterior has scratches and line scratches. Serial 619097168 (Fujisawa Yukishi)
Maintenance information: 2024.5.17 Maintained (loading and clamp mechanism drive belt replacement. Front panel operation tact switch replacement. Optical system cleaning cleaning)
Accessories: No accessories
Main specifications: 1-bit linear & direct conversion system (4DAC) W430 × H127.5 × D397.5 mm 8.8 kg
SAEC long-selling model with a 0.6 m digital cable. 6N ultra-high purity copper with excellent transmission characteristics is used as the conductor material, and transmission loss is reduced with accurate impedance matching (Tamura Eiji)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
The price has been drastically reduced! 2024/5/9 sales price 39,800 yen D/A converter with a built-in “ES9038PRO.” This model has a compact design, is compatible with MQA, high-resolution, and DSD sound sources, and has excellent cost performance. Desktops etc. are the worst. There are no noticeable scratches on the exterior (Tamura Eiji)
Maintenance information: 2024.5.9 operation confirmed
Accessories: instruction manual (no Japanese), remote control, AC adapter
Main Specifications: Input: USB/OPTICAL/COAXIAL/BLUETOOTH USB: 44.1 to 768 kHz/DSD64 to 512 OPTICAL/COAXIAL: 32 to 192 khz W100 x H62 x D192 mm Weight 0.58 kg
※Since it is cheap, it will be handed over as is. 1 bottle only 25cm full range speaker made by RCA in the USA. The Alnico magnet responds well and the sound is easy to remove. There are repair marks on the edge (Tamura Eiji)
Maintenance information: 2024.3.22 sweep test good
Accessories: No accessories
Key Specifications: Unit Diameter 25cm 8Ω Fixed Edge
The price has been drastically reduced! 2024/4/19 sales price 79,800 yen ※1 unit only. Maintained! It is originally a professional mono amplifier, but there is only 1 unit. You can feel the strong power of the sound quality even with just one unit. It seems to be useful for mono and center speakers. There are scratches and paint peeling on the exterior. Serial Q001769 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (XLR speaker cable created (3 meters)). Electrolytic capacitor replacement. ATT cleaning. Solder correction. Rubber feet added. Bias offset check. Output audio check. Input ① GND ② HOT ③ GND (unbalanced) output ① not used ② is set to plus ③ minus 8 Ω load. (Also, a pop sound is made when the power is on and off, but this is a specification)
Accessories: speaker cable, power cable
Main specifications: 8 ohms W482.6 x H88 x D320 mm weight 13 kg
The price has been drastically reduced. 2024/4/22 sales price 128,000 yen Maintained! A famous machine 44 with an easy-to-handle RCA terminal added to the rear terminal of the Quad control amplifier. The British QUAD's small preamp is a perfect balance between the freshness and richness of character. You can enjoy a calm, high-quality sound when paired with the same speakers made in England (Murakoshi Yoichi)
Maintenance information: 2024.4.18 maintenance (internal all checks, power supply filter C ± B bypass C replacement, balance VOL cut off sound → cleaning, check each board)
Accessories: 2 DIN input cords, power cord, instruction manual (copy)
Main specifications: 2 LINE inputs, 2 TAPE2 systems (DIN input or more), 1 PHONO input system, Phono sensitivity 1m/3m/10mV switching W321 x H103 x D203 mm 4 kg
Maintained! A classic British Quad stereo power amplifier. Small in size yet full torque. The sound, which is as deep as a tube amp, exudes an appeal that won't fade. The exterior has a feeling of use over time, such as dullness and small scratches. Serial 62226 (Yonejima Satoshi)
Maintenance Information: 2024.3.25 Maintained (INPUT DIN 4P replacement, internal Tr, C, R all checks. DIN4P-RCA female cable created. Operation check, pattern solder processing)
Accessories: power cable, connection cable
Main specifications: 45W+45W W120×H159×D324mm 8.2 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/11/11 sales price 99,800 yen Maintained! A preamplifier that can be operated by a full remote control. A familiar quad tone that is natural, easy to listen to and won't get tired of. In addition to volume, left and right balance, input switching, etc., it is fully equipped with functions such as TILT (loudness like function) and high pass and low pass filters (2 levels each), which is convenient. The exterior has peeling paint and repair marks on the bottom. Serial Q 202547 (Tamura Eiji)
Maintenance information: Maintained on 2015.2.23 (reworking the solder on the printed circuit board pattern on the power switch part of the amplifier body. Electrolytic capacitor replacement in the main unit. The CD/PLAY button installation on the remote control has been reworked. Remodeling the remote control emitting diode mounting position. aging test. (Check the operating distance range of the remote control → around 5m)
Accessories: remote control, power cable
Main specifications: full remote control control amplifier with PHONO input W321 x H80 x D255 mm 3.3 kg
The price has been drastically reduced! 2024/5/11 sales price 128,000 yen Maintained! Late QUAD44 with CD input terminal. It's not flashy, but the thick, glossy tone is attractive. In particular, it softens female vocals. Serial Q36114 (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (internal power supply switch contact dirt contact polishing treatment, balance VOL cleaning ~ check OK. Check the other boards and re-solder the holes. (C, R check OK)
2024.5.9 Internal power supply switch contact polishing treatment
Accessories: power cord
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321 x H103 x D203 mm, 4.0 kg
A compact, high CP, and easy headphone amplifier. The sound is bright and has good visibility. A well-balanced model that works well with everything from pop to rock. Serial 32741 (Fujisawa Yukishi)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: instruction manual, AC adapter
Main specifications: output 330 mw/30 ohm, 60 mw/300 ohm headphone amplifier connection, 30 ohm gain, 11 dB S/N ratio, 87 dB frequency characteristics, 30 to 20 kHz, input/output RCA, 1 system each, W103 x D127 x H38 mm, 1.40 kg
The price has been reduced! 2024/5/25 sales price 69,800 yen ※The exterior is in poor condition, so it's cheap. An upgraded model of PMC's small monitor DB1. It has excellent characteristics as a near-field monitor, and is characterized by good phase characteristics and rich spatial expression. It is a high-quality model that can be further upgraded by adding an amplifier. There are line scratches and bumps on the exterior. Also, there are cracks or tears in the urethane on the back. Serial 012503/012504 (Yonejima Satoshi)
Maintenance information: 2024.5.25 sweep test good
Accessories: saran net
Main specifications: 2 way 2 speakers, frequency characteristics, 50 Hz to 25 kHz, output sound pressure level, 87 dB, impedance, 8 ohms, dimensions: H290 x W155 x D240 mm (including grille), mass: 4.5 kg