Cotter's most popular MARK2 TYPE L MC boost transformer for low impedance such as orthophones. Using a strong, sealed case and silver wire, the strong and fresh tone is attractive. Perfect compatibility with SPU etc. The transformer itself is different from P/PP/S. RF Enterprise regular import model. ※Silver wire breaks easily, so please handle it carefully (Murakoshi Yoichi)
Main specifications: primary impedance 1 to 6 ohm silver wire triaxial output cable, adopted size W76 x H55 x D150 mm, approx. 1.3 kg
This is a specially designed product in which the company's original neighboring bronze machined pin terminals are set on the HS-1A using African ebony wood, and 6N copper wire with excellent sound quality is used as the shell lead. Since lead wires are soldered to the terminals on the arm side, sound quality improvement effects can also be expected due to a reduction in electrical contacts (Murakoshi Yoichi)
Maintenance information: 2024.6.11 continuity confirmed
Accessories: mounting screws
Main specifications: African ebony wood (eco-paint buff finish), brass finger tips (non-magnetic gold plated finish), own weight 10.2 g
※The cantilever is slightly tilted to the right. It is a universal specification that can be used with normal arms. Tuned based on EMT professional cartridges. A Vandenhall stylus is used. The sharp low range and the thick, powerful mid-high range are attractive (Murakoshi Yoichi)
Maintenance information: 2024.6.12 sound output confirmed
Accessories: none
Main specifications: output voltage 0.15 mV (1 cm/sec 1 kHz) needle pressure 2.0 to 3.0 g playback frequency band 15 to 25,000 Hz channel separation 25 dB compliance 15 x 10-6 cm/dyne internal impedance 24 Ω needle tip super oval dead weight 17.5 g
A universal model that can be used with standard tone arms. A long-time seller where you can feel the vividness of the studio atmosphere of each era and even the heat of the performance. You can enjoy a thick and powerful sound (Murakoshi Yoichi)
Maintenance information: 2024.6.12 sound output confirmed
Accessories: original box
Main specifications: MC type needle pressure 2.5 g impedance 22 ohms own weight 17.6 g
RCA cable 2.0m pair genuine molded plug, the honest, thick, and powerful sound with medium and low sounds that are unimaginable from the way they look is addictive (Tomoho Asaine)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
RCA cable, 1.2 m pair, genuine molded plug, and the honest, thick, and powerful sound with medium and low sounds, which is unimaginable from the way it looks, is addictive (Asaine Tomoho)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
RCA cable, 1.0 m pair, genuine molded plug, and the honest, thick, and powerful sound with medium and low sounds, which is unimaginable from the way it looks, is addictive (Asaine Tomoho)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
RCA cable, 1.0 m pair, genuine molded plug, and the honest, thick, and powerful sound with medium and low sounds, which is unimaginable from the way it looks, is addictive (Asaine Tomoho)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
RCA cable, 0.7 m pair, genuine molded plug, and the honest, thick, and powerful sound with medium and low sounds, which is unimaginable from the way it looks, is addictive (Asaine Tomoho)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
RCA cable, 0.7 m pair, genuine molded plug, and the honest, thick, and powerful sound with medium and low sounds, which is unimaginable from the way it looks, is addictive (Asaine Tomoho)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
The price has been reduced! 2024/6/14 sales price 17,800 yen speaker cable This is an abnormally thin cable for a 3.5 m pair of unprocessed speaker cables with untreated terminals. A cable boasting high resolution and a high amount of information. The sound quality changes drastically depending on how you use it, such as separating the main amplifier and speaker, and shortening the speaker cable, so it's fun to drive the sound quality to your own liking (Tomoho Asaine)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
The price has been reduced. 2024/6/14 sales price 14,800 yen speaker cable This is an abnormally thin cable for a 3.0 m pair of unprocessed speaker cables with untreated terminals. A cable boasting high resolution and a high amount of information. The sound quality changes drastically depending on how you use it, such as separating the main amplifier and speaker, and shortening the speaker cable, so it's fun to drive the sound quality to your own liking (Tomoho Asaine)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
RCA cable, 0.7 m pair, genuine molded plug, and the honest, thick, and powerful sound with medium and low sounds, which is unimaginable from the way it looks, is addictive (Asaine Tomoho)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
RCA cable, 1.0 m pair, genuine molded plug, and the honest, thick, and powerful sound with medium and low sounds, which is unimaginable from the way it looks, is addictive (Asaine Tomoho)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
The price has been drastically reduced. 2024/6/14 sales price 428,000 yen Luxman's current phono equalizer using a non-feedback CR type amplifier circuit using all-stage vacuum tubes has arrived! Using vacuum tubes, 4 independent Super Permaloy MC boost transformers and 4 output transformers are mounted on the left, right, and low/high, respectively. It is a model that emphasizes sound quality, using a VU meter and OFC, which are fun to look at. It is one that can be controlled in a variety of ways. The condition is generally good. Serial M20700210A (Yamato Yuki)
Maintenance information: 2024.6.13 operation confirmed
Accessories: instruction manual power cable
Main specifications: circuit method: SRPP, terminal cathode follower, non-feedback CR type equalizer (RIAA) vacuum tube: ECC83 x 4, ECC82 x 2, EZ81 x 1 input sensitivity (1 kHz, when gain is switched 36 dB): MM 4mV, MC high 0.44mV, MC low 0.18mV input impedance: mm30kΩ to 100kΩ (variable), MC high 40Ω, MC low 2.5Ω gain (1kHz, when gain is switched at 36 dB): mm36dB, MC High55dB, MC Low63dB S/N ratio mm76dB, MC High75dB, MC Low74dB W440 x H92 x D397mm weight 12.5 kg
The balance cable uses an 8-core multi-hybrid conductor with 2 pairs of 4 types of copper wires arranged in each of the 4 types of 1.0 m pair, 7N ultra-thick high-purity copper wire AgA silver-plated annealed copper wire, PCOCC single crystal oxygen-free copper wire, and OFC oxygen-free copper wire. This cable has an excellent balance between sound thickness and stretchability (Tomoho Asaine)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
optical cartridges. The cantilever has become boron, and I feel that the overall density, especially in the low range, has increased. The quietness and sense of speed that makes you forget you're listening in analog for a moment have been particularly improved, and it's a convincing degree of perfection that it can be positioned as a new reference (Asaine Tomoho)
Maintenance information: 2024.6.14 sound output confirmed
Accessories: original box screw hex wrench
Main Specifications: Power Generation Method Photoelectric Cantilever Boron Body Material Machined Aluminum Needle Pressure 1.85g-2.05g (Recommended 1.95g) Weight 7.9g
An upper and lower pin structure is used to make the pressure at the contact point uniform. Contact surface stabilization is achieved with a spherical washer. High rigidity is maintained by completely machined super duralumin and manufactured in an integrated manner up to the finger holder (Asae Satoshi Method)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
Main specifications: Super duralumin fully integrated machined body, black nickel plating, weight 10.5 g (lead wire not included), 11.0 g (lead wire included)
A floor-type speaker with an authentic 3-way configuration with all-round appeal, from pure audio to theaters. The wide range playback has a sense of volume, and there is an exhilarating feeling that you can drop out the mids and highs that are particularly calm and easy to hear. There is a crack in part of the plastic that covers the magnet on the saran net (Sasaki Shota)
Maintenance information: 2024.6.13 operation confirmed
Accessories: jumper plate
Main specifications: 3-way bass reflex type (non-magnetic) playback frequency band 45 Hz to 50 kHz impedance 6 ohms sound pressure level 89 dB W354 x H1,012 x D374 mm weight 25.0 kg
※There is no problem with operation, but the phono cable and original box manual are missing, so it's cheap. There is also only 1 weight. This is a masterpiece arm with one-point support, static balance, and oil dump system. The light arm movement and the sense of balance between the delicate high range and the power of the mid to low range are excellent (Sasaki Shota)
Maintenance information: 2024.6.13 operation confirmed
Accessories: none
Main specifications: static balance type, total length 333 mm, effective length: 237 mm, overhang: 15 mm, needle pressure range: 0 to 3 g (0.25 g steps), compatible cartridge, dead weight: 3 to 17 g
PSE certified product. Oyaide's 6-port power strip uses a 1.6 mm thick stainless steel chassis with extremely high rigidity. It is a high quality power strip that is particular about internal wiring and inlet materials (Sasaki Shota)
Maintenance information: 2024.6.13 operation confirmed
Accessories: none
Main specifications: 1.6mm thick SUS304 stainless steel housing, OFC2mm single wire inlet, thick silver plated+thick rhodium plating, W70 x H50 x D385 mm, 1,800 g
FR heavyweight headshell In combination with a heavy needle and pressure needle, it exhibits excellent tracing performance, such as digging up from deep inside a groove on a record board (Sasaki Shota)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: none
Main specifications: aluminum press processing actual measurement 19g
FR heavyweight headshell In combination with a heavy needle and pressure needle, it exhibits excellent tracing performance, such as digging up from deep inside a groove on a record board (Sasaki Shota)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: none
Main specifications: aluminum press processing actual measurement 19g
MC cartridge using LC-OFC (linear crystal/oxygen-free copper) wire based on DL-103. Familiar sound with a wide range. It has a supple sound and is comfortable to listen to. The needle tip is good (Sasaki Shota)
Maintenance information: 2024.6.13 Sound output operation confirmed
Accessories: needle cover
Main specifications: MC type output 0.25 mV, proper needle pressure 2.2 to 2.8 g, internal impedance 13 ohms, own weight 8.5 g
Equipped with a WD RED 3TB x 2 HDD. It is currently SHR mirrored. Equipped with an 8th generation Intel Celeron J4025 2-core CPU (2.0 GHz, maximum 2.9 GHz). Until recently, it was used as sound source storage for Roon. There is a line wound on the front desk (Yasuhito Koshihama)
Maintenance information: 2024.6.13 storefront operation confirmed
Accessories: power adapter
Main specifications: Intel Celeron J4025 64 bit 2 core CPU system memory 2GB DDR4 non-ECC (maximum 6GB 2GB+4GB) LAN x 2 ports (1Gb) 3.5 inch SATA HDD x 2 bays W108 x H165 x D232 mm 1.3 kg
Roon Rock installed. Equipped with an M.2 SSD 250GB x 1 for startup and 16GB x 1 memory. Equipped with a 10th generation Core i7 with 6 cores and 12 threads. We provide a comfortable Roon Server with high sound quality (Yasuhito Koshihama)
Maintenance information: 2024.6.13 storefront operation confirmed
Accessories: power adapter, original box
Main specifications: Equipped with CPU 10th generation Core i7-10710U
* There is no name plate, but I was able to confirm a slight embossing of the model number on the belt seal on the side. Output: 50W for transparent sale push pull output: 50W primary: 5kΩ secondary: 4/8/16/32Ω use: 6L6, 6CA7, 6GB8, etc. W100 x H115 x D90 mm approx. 3.5 kg/piece, no name plate, and is inexpensive because it has been repainted and written on the entire surface (Kojima Yosuke)
Accessories: none
Line matching transformer pair sale primary side: 600 Ω CT (150 split) secondary side: 20 kΩ CT (5 k split) W77 x H71 x D43 mm approx. 0.55 kg/piece (actual measurement, not including protrusions) (Kojima Yosuke)
Accessories: none
Output transformer pairs for sale for heavyweight large transformers, primary: 3.5 kΩ, secondary: 4-8-16 ohms, W150 x H185 x D150 mm, 11.2 kg/piece (actual measurement, not including protrusions) there are hook scratches in places (Kojima Yosuke)
Accessories: none
It seems to be a Tektron interstage transformer, but detailed specifications are unknown. Pair sale primary: 10 kΩ secondary: 10 kΩ x 2 W80 x H100 x D70 mm 1.4 kg/piece (actual measurement, not including protrusions) (Kojima Yosuke)
Accessories: none
※The earpads are not in good condition, so they are cheap. These open-air headphones feature well-balanced, natural sound from high to low frequencies. Try a slightly different sound from low impedance headphones. ※The cable has been replaced. On the exterior, there are dirt and cable marks on the earpads and head pads (Satoshi Yonejima)
Maintenance information: 2021.11.12 sweep test good
Accessories: original box
Main specifications: dynamic open air headphones, 300 ohms, 97 dB, 12 to 40,500 Hz, plug shape, 4.4 mm
6N copper wire with multiple gauge (wire diameter) structure is used to improve performance as a 1.0 m pair conductor of the RCA cable. You can enjoy the clear and fresh MIT sound even with this entry model. The exterior is dull and some characters are missing (Yonejima Satoshi)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: original box
The 1.5m optical digital cable uses the world's first hyperbundle (different diameter multi-core) fiber metal flexible pipes to protect and suppress vibrations. High-grade stable optical cable model. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: original box
Optical digital cable 1.0 m This product has greatly increased transmission speed to support high-tech manufacturing technology, refractive index control, and high sampling software. The core is a high-speed, high-capacity (broadband) pure quartz fiber developed by making full use of precision processing technology. The exterior is good (Yonejima Satoshi)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: original box
The 2.0m optical digital cable is probably a model that has not been sold in Japan. There is a slight stickiness on the sheath (Tamura Eiji)
Maintenance information: 2024.6.13 operation confirmed
Accessories: case
This is the entry model for NORDOST with a 1.5m pair of RCA cables. The inexpensive yet clear and sharp sound inherits the taste of advanced models. It has creases and a bit of a habit (Yonejima Satoshi)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: none
The 1.8 m PSE standard PCOCC-A conductor 3-layer shield plug is phosphor bronze plated with gold and palladium, and a tight sound comes to the front, giving it a sense of dynamism. Although it is an affordable cable, you can feel the changes greatly due to the power cable, and the exterior is dull. ※The wire is hard and the cable is slightly difficult to handle (Satoshi Yonejima)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: original box
The 1.8 m PSE standard PCOCC-A conductor 3-layer shield plug is phosphor bronze plated with gold and palladium, and a tight sound comes to the front, giving it a sense of dynamism. Although it is an affordable cable, you can feel the changes greatly due to the power cable, and the exterior is dull. ※The wire is hard and the cable is slightly difficult to handle (Satoshi Yonejima)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: original box
The 1.5m PSE standard power cable is a full-tech FI-25 plug, and the sheath uses new materials that respond to environmental issues in 2006. The mid to low range with horsepower is recommended for jazz and rock fans. The exterior is good (Yonejima Satoshi)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: original box
The XLR cable uses 1.0 m pair of high-purity silver wires and a multi-shield structure of Gore-Tex, copper foil, and Teflon. The high level of transparency that is clear and has no peculiarities is attractive. Fits a wide range of devices. (YONEJIMA Satoshi)
Maintenance information: 2024.6.11 continuity confirmed
Accessories: none
Use the original 24K gold-plated plug with a 1.5m pair of RCA cables, polished by hand and nickel plated. The characters are highly transparent and sharp. It greatly enhances the freshness of the sound. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: original box
RCA cable 1.5m pair with AC adapter Synergistic Research's top-grade reference series entry model. 2-core twist construction The clear, three-dimensional, and realistic sound images unique to Synergistic are appealing. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.6.11 continuity confirmed
Accessories: AC adapter
TMD balance cable using a 1.0 m pair of single-wire XLR cables. It's a cable with a TMD-like tone. The exterior has frayed cloth (Tamura Eiji)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: No accessories
Thoroughly review the interior and carry out maintenance on capacitors, transistors, etc.! A vintage model representing JBL. In addition to the extremely powerful and well-extruded sound quality, it also has a dry and tight tone unique to this era. The strong sense of energy in the low frequencies and the characters with clear outlines are excellent matches with old JBL speakers. It is a vintage masterpiece that stands out for its individuality. There is a slight feeling of use on the exterior. Serial 2362 (Murakoshi Yoichi)
Maintenance information: 2024.6.12 maintenance (test switch contact defects, other internal checks. DC leak due to leaks such as C in both ch couplings, poor Tr characteristics in the pre-stage, poor characteristics of the power stage Rch transistor x 1 → replacement. (Each VOL rotary SW is large → all cleaning, ~ operation check)
Accessories: instruction manual (copy), power cord
Main specifications: 40W+40W (8Ω) W412 × H128 × D350 mm 11.8 kg
Elliptical type with built-in boost transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. Serial 830693 (Murakoshi Yoichi)
Maintenance information: 2024.6.11 sound output confirmed
Accessories: original box, needle cover, brush
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
A universal model that can be used with standard tone arms. A long-time seller where you can feel the vividness of the studio atmosphere of each era and even the heat of the performance. You can enjoy a thick and powerful sound (Murakoshi Yoichi)
Maintenance information: 2024.6.12 sound output confirmed
Accessories: original box, characteristic table
Main specifications: MC type needle pressure 2.5 g impedance 22 ohms own weight 17.6 g
Comes with original box! It is a universal specification that can be used with normal arms. Tuned based on EMT professional cartridges. A Vandenhall stylus is used. The sharp low range and the thick, powerful mid-high range are attractive (Murakoshi Yoichi)
Maintenance information: 2024.6.12 sound output confirmed
Accessories: original box
Main specifications: output voltage 0.15 mV (1 cm/sec 1 kHz) needle pressure 2.0 to 3.0 g playback frequency band 15 to 25,000 Hz channel separation 25 dB compliance 15 x 10-6 cm/dyne internal impedance 24 Ω needle tip super oval dead weight 17.5 g
An acoustic panel for floors that mainly diffuses rather than absorbs sound. It is designed so that an overwhelming effect can be obtained in a limited space. The exterior is dull and has a feeling of use (Hiroki Aso)
Accessories: none
Key Specifications: Hybrid Diffusion Floor Panel W680 ✕ H36 ✕ D680mm 4kg