The interior has been completely overhauled! This is an 811A push-pull tube power amplifier. You can enjoy an overhanging vacuum tube sound with luxurious mono specifications where the woofer is properly braked. The thick, cored sound in the low range makes you feel the momentum and strength unrivaled for a vacuum tube. The entire exterior has scratches and dullness over time (Sasaki Shota)
Maintenance information: 2024.4.26 Maintained (vacuum tube 5R4GY strain and deterioration replacement. 1W resistor distortion and deterioration replacement. 25W resistance deterioration and pair replacement. Vacuum tube 6W6 deterioration replacement/vacuum tube 6SN7 defective replacement. Block capacitors 40 μF x 2 made in Japan → replaced with CE ones. 1 x 2 Vacuum Tube Socket and RCA Jack Caulking Repair Rated output: 85 to 120 W with AC 100 to 117 V, measured at SP: 8 ohms)
Accessories: none
Main specifications: vacuum tube 811A x 4, 5R4GY x 8, 6W6GTB x 4, 6SN7GTB x 2, 12AX7 x 2, 165W+165W W482 x H272 x D310 mm
Maintained by Denon Service! This model was commercialized by setting up the DA-305 on the DP-3000. The tone arm is simple and easy to handle, so it's easy to set up. The content firmly captures the basics. You can fully enjoy the goodness of analog, and this model is also recommended as an introductory machine (Sasaki Shota)
Maintenance information: 2024.4.26 manufacturer maintained (13 deteriorated TRs replaced. speed adjustment, sound output test)
Accessories: copy of the manual
Main specifications: 30cm die-cast aluminum (DP-3000) direct drive static balance S-shaped tone arm (DA-305) oil dump arm lifter needle pressure adjustment range 0 to 3 g compatible cartridge weight range 4 to 15 g W530 x H180 x D440 mm weight 10.8 kg
Maintained! A hit model during the heyday of audio by Sony. It has a relaxed, thick tone that you won't get tired of listening to, and it faithfully expresses the sauce without unnecessary seasoning. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 212487 (Hiroki Aso)
Maintenance information: 2024.4.26 maintained (MUT switch, push slide, SW exchange, volume VR, sound replacement, speaker relay due to deterioration, 14 parts replacement, other input selector, cartridge selector, each SW disassembly contact, polishing grease application, etc., DC bias balance adjustment, each input/output sound output check)
Accessories: copy of instruction manual
Main specifications: 105W+105W (8Ω) PHONO MM/MC (40Ω/3Ω) W430 × H161 × D436 mm 19.6 kg
※ Tweeter soft dome has dents on the rim, so it is inexpensive. Compact Excite series speakers. There is a sense of power in the sound unique to unit development manufacturers, and the sense of scale in the low range in particular is so majestic that the compact size is unbelievably large. As the sound progresses, the transparency of the sound increases, so the fact that you can keep listening is also attractive. There is a slight feeling of use such as small scratches. Serial 03573940/03573941 (Takasaki Atsushi)
Maintenance information: 2024.4.21 sound output confirmed
Accessories: saran net
Main specifications: 2-way bass reflex type 180mm woofer 27mm tweeter 4Ω 87dB frequency band 40Hz to 23kHz W205 x H350 x D290 mm 9.0 kg
Maintenance is being carried out in 2022. A reprint of Marantz's famous model 7. In addition to the good graininess of the sound and the glossy and rich sound quality, it brilliantly inherits the good quality of the mid-range. You can enjoy a feeling that transcends ages and genres. The exterior has dullness and scratches. Serial F020306 (Murakoshi Yoichi)
Maintenance information: 2022.3.22 maintenance (implementation of measures to prevent the rear input terminal and chassis earth from floating, hot side loosening, contact pressure correction. Clean each vacuum tube pin and socket contact. (Volume VR part ground wire deviation correction, wood case stop screw installation)
Accessories: instruction manual (copy)
Main specifications: used vacuum tube 12AX7×6 W455×H178×D261mm 8kg
A standard model of domestic mono cartridges. A popular model that condenses the appeal of a mono needle, which has a thick overall sound and is also powerful. It is also attractive that the output is high and can be used without a step-up transformer (Murakoshi Yoichi)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: case, needle cover, instruction manual
Main specifications: output voltage 3 mV playback frequency 50 Hz to 10 kHz impedance 240 ohms compatible load 1 kΩ or more needle tip 17 microns diamond round needle needle pressure 3G
It is an ambitious K2 series mid-range model that inherits the characteristics of the S9500. The dynamic sound quality that makes use of the horn stands out for the strength of the sound image. The sound is lively and full of life, and the realism of the bass is outstanding. The exterior has line marks and dullness. Serial J1240-010742, J1240-010709 (Fujisawa Yukishi)
Maintenance information: 2024.4.26 operation confirmed
Accessories: saran net, jumper plate
Main specifications: 2 way 3 speakers · bass reflex system · tall boy type 30 cm cone type (LE125S) x 2 high range horn type (275Nd) frequency characteristics 35 Hz to 20,000 Hz output sound pressure level 95 dB impedance 4 Ω maximum allowable input 150 W crossover frequency 800 Hz W499 x H1,254 x D412 mm 89kg/1
※Because it smells like tobacco, it's cheap. Maintained! Custom edition of the large power amplifier PA-70 from the STASIS circuit. Supported by a huge 700W toroidal transformer, the speaker driving power, which consists of a 90A power supply, is one of the best among domestic amplifiers. Fortissimo, which excels at delicate depictions but doesn't make you feel limited, is unique to this large amplifier. The exterior is dull and scratched. Serial 11179 (Fujisawa Yukishi) A
Maintenance information: Maintained on 2024.4.26 (bias part and constant current part semi-fixed VR, output relay, and damaged screws were replaced, additional installation due to lack of cable protector, solder crack correction, bias and offset adjustments, output sound check, dirt removal and cleaning)
Accessories: No accessories
Main specifications: rated output 225W+225W (8Ω) W435 x H200 x D421 mm approx. 28.5 kg
This overhang gauge is convenient for positioning cartridges. The A side can be used for the record needle side slip test, and the B side can calibrate the cartridge part (Murakoshi Yoichi)
Accessories: none
Main specifications: acrylic diameter 295mm, thickness 2mm 154g
This is a rare KEF center speaker Q6C in stock. It is a well-balanced and well-organized sound character typical of the Q series. It seems to express a sufficient sense of sound field even when used in combination with Q1 for theaters. There is a bruise on the upper back corner. Serial 2027685G (Murakoshi Yoichi)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: jumper plate, saran net
Main specifications: 2-way bass reflex low range/130mm Uni-Q high range/19mm Luminiumdome frequency characteristics 50Hz-27kHz crossover frequency 2.8kHz 89dB 8Ω W432xH160xD215mm 4.1 kg
Digital cable, 1.0m, RCA terminal, cotton blade, riz wire conductor with a stranded coaxial sheath structure, is a nuclear-free type, but it is a cable that makes you feel strong in the mid-range similar to having a core. The plug is dull, and the sheath has fading and fraying over time ※Please connect the red plug ring side to the output terminal and the white plug ring side to the input terminal (Kojima Yosuke)
Accessories: none
Digital cable, 1.0m, RCA terminal, cotton blade, riz wire conductor with a stranded coaxial sheath structure, is a nuclear-free type, but it is a cable that makes you feel strong in the mid-range similar to having a core. The plug is dull, and the sheath has fading and fraying over time ※Please connect the red plug ring side to the output terminal and the white plug ring side to the input terminal (Kojima Yosuke)
Accessories: none
The speaker cable is a conductor consisting of 350 cores in all, a 2.0m pair of end rod terminals, and is very heavy (about 2 kg per piece with only the core box part!). It has a unique presence, full of a sense of craftsmanship that cannot be found with other cables. Contrary to being rugged, the sound is detailed and smooth. As you raise the volume, you can see its true value. There are scuffs, fraying, and dirt on the sheath ※Since the core box is extremely heavy, installation requires ingenuity so that no load is applied to the cable and speaker terminals. The distance from the box to the cable terminal is approximately 15 cm. Connect the terminal side with the red seal in the middle of the sheath to the amplifier, and the terminal on the core box side to the speaker (Kojima Yosuke)
Accessories: none
Main specifications: total weight 4.8 kg
The speaker cable is a conductor consisting of 350 cores in all, a 2.0m pair of end rod terminals, and is very heavy (about 2 kg per piece with only the core box part!). It has a unique presence, full of a sense of craftsmanship that cannot be found with other cables. Contrary to being rugged, the sound is detailed and smooth. As you raise the volume, you can see its true value. There are scuffs, fraying, and dirt on the sheath ※Since the core box is extremely heavy, installation requires ingenuity so that no load is applied to the cable and speaker terminals. The distance from the box to the cable terminal is approximately 15 cm. Connect the terminal side with the red seal in the middle of the sheath to the amplifier, and the terminal on the core box side to the speaker (Kojima Yosuke)
Accessories: none
Main specifications: total weight 4.8 kg
RCA cable 1.0 m pair is a characteristic line cable that makes a careful overall sound and feels strong in the middle range of pianos, etc. The area around the plug is dull, and there are abrasions, fraying, and dirt on the sheath ※Since the core part is very heavy, installation ingenuity is necessary so as not to put a load on the plug or jack to be connected (the cable length at the end of the core box is about 15 cm) *Connect the terminal side with the red seal in the middle of the sheath to the output terminal, Connect the terminal side where the core box is located to the input terminal (Kojima Yosuke)
Accessories: none
Main specifications: total weight 1 kg
Digital cable, 1.0m, RCA terminal, cotton blade, riz wire conductor with a stranded coaxial sheath structure, is a nuclear-free type, but it is a cable that makes you feel strong in the mid-range similar to having a core. The plug is dull, and the sheath has fading and fraying over time ※Please connect the red plug ring side to the output terminal and the white plug ring side to the input terminal (Kojima Yosuke)
Accessories: none
RCA cable 1.0 m pair is a characteristic line cable that makes a careful overall sound and feels strong in the middle range of pianos, etc. There is dull writing around the plug, and there are abrasions, fraying, and dirt on the sheath ※Since the core part is very heavy, installation requires ingenuity (the cable length at the tip of the core box is about 15 cm) *Connect the terminal side with the red seal in the middle of the sheath to the output terminal, and input the terminal side with the core box Please connect to the terminal (Kojima Yosuke)
Accessories: none
Main specifications: total weight 1 kg
RCA cable 1.0 m pair is a characteristic line cable that makes a careful overall sound and feels strong in the middle range of pianos, etc. The area around the plug is dull, and there are abrasions, fraying, and dirt on the sheath ※Since the core part is very heavy, installation ingenuity is necessary so as not to put a load on the plug or jack to be connected (the cable length at the end of the core box is about 15 cm) *Connect the terminal side with the red seal in the middle of the sheath to the output terminal, Connect the terminal side where the core box is located to the input terminal (Kojima Yosuke)
Accessories: none
Main specifications: total weight 1 kg
G-shell oval needle model from the Herman era. The glossy, rich, and heavy sound is an appeal that never fades. It is an eternal cartridge that fully conveys the appeal of analog (Yasuhito Koshihama)
Maintenance information: 2024.4.25 storefront operation confirmed
Accessories: original box
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
※Since it is cheap, it will be handed over as is. An attractive subwoofer with a tight, speedy bass range based on time domain theory. The sound that emits 360 degrees is a convenient item with a high degree of freedom of installation. There are scratches on the exterior. Serial Z0C00005 (Tamura Eiji)
Maintenance information: 2024.4.24 sweep test good
Accessories: instruction manual, power cable, original box
Main specifications: 16 cm subwoofer 16 cm (dual voice coil unit) playback frequency band 40 Hz to 200 Hz rated output 30 W x 2 crossover 40 Hz to 200 Hz (continuously variable) power consumption 46 W size W236 x H354 x D301 mm mass 16.2 kg
RCA cable, 1.0 m pair, 6N-7N hybrid conductor, twin core structure, thick and strong mid-range, this hidden name cable is recommended for vintage audio. There is dirt on the sheath (Tamura Eiji)
Maintenance information: 2024.4.24 continuity confirmed
Accessories: No accessories
The price has been drastically reduced! 2024/4/24 sales price 118,000 yen*Saran net is out of stock, scratches, etc.
It's cheap because it's not in good condition. ATC small bookshelf. The thick and powerful mid-low range is attractive. If you pair it with a good amplifier that has torque, you can enjoy it on a scale that greatly exceeds its size. There are scratches on the exterior. Serial 0819/0820 (Tamura Eiji)
Maintenance information: 2024.4.24 sweep test good
Accessories: No accessories
Main specifications: 2 way 2 speakers sealed impedance 8 ohms size W211 x H380 x D250 mm weight 11.4 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/22 sales price 148,000 yen Maintained! A driver unit suitable for sound reproduction for large halls and theaters, modeled after the standard 2-inch 375. High frequency characteristics have been enhanced while retaining a vintage feel. The cymbals play a sound that makes you think of jazz. The paint is peeling off. Serial 32769, 32799 (Fujisawa Yukishi)
Maintenance information: 2024.4.22 maintained (diaphragm installation adjustment, pad dampener replacement)
Accessories: No accessories
Main specifications: frequency characteristics, 500 to 18 kHz, crossover, 500 Hz, 16 ohms, diameter: 175 mm, height: 145 mm, approx. 11.8 kg/bottle
A model developed for the digital AV era by applying anti-magnetic treatment to the NS-10M. The clear high frequencies stretch comfortably with less color quality. It is useful for a wide range of applications, such as those who are worried about space and for subsystems. The exterior has scratches, small scratches, and a feeling of use. Serial 104369A, 104369B (Fujisawa Yukishi)
Maintenance information: 2024.4.23 Operation confirmed
Accessories: saran net
Main specifications: 2 way 2 speaker sealed type 8 ohm sound pressure 90 dB W215 x H382 x D199 mm 7.0 kg
The 1.3 m power cable uses a polymer polyolefin material for the untreated terminal sheath. The thickness, which can be called overspec, ensures high speed and large current capacity. You can see the exterior, dullness, threads, etc. and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.19 Continuity confirmed (PSE certified product)
Accessories: none
An original needle! This is Type 4 of the classic V15 series. The impression is that sharper resolution and a sense of dynamism have been added than Type 3. The tracing ability is extremely high, and it picks up the sound engraved in the sound groove without omission (Oikawa Tetsuji)
Maintenance information: 2024.3.31 operation confirmed
Accessories: none
Main specifications: mm type output voltage 4 mV needle pressure 0.75 to 1.25 g internal impedance 47 kΩ dead weight 7 g
The disposal price has been reduced! (Member prices are not applicable) 2024/4/17 sales price 278,000 yen This is an advanced model of the company's SACD player with a beautiful blaster white body color. It has a higher fidelity tone than conventional luckstones, and the sound image with high instantaneous power, especially the elasticity in the mid and low frequencies, is attractive. On the exterior, there are scuffs scattered on the top plate and side plate. Serial G11100859D (Yonejima Satoshi)
Maintenance information: 2024.4.17 operation confirmed
Accessories: remote control, instruction manual, power cord
Main specifications: SACD/CD player equipped with PCM1792 x 2 D/A converter W440 x H140 x D383 mm 15.5 kg
The price has been reduced! 2024/4/23 sales price 65,000 yen caster specification! TAOC theater youth HT series wide rack. It also has sufficient load carrying capacity, so even those with large devices can use it without worry. Other than one scratch on the pillar, the condition is pretty good. *Shipping costs will be estimated separately. (FUJISAWA KOSHI)
Accessories: instruction manual, felt, logo seal, hex wrench
Main specifications: load capacity 200 kg/1 shelf spacing 180/230 mm W1,680 x H590 x D550 mm weight 65 kg
The price has been reduced! 2024/4/18 sales price 59,800 yen ※Since it is a commercial device, it will be handed over as is. It's a very powerful sound unique to professional machines, and it pushes the sound forward and forward. Recommended for jazz and rock fans with large woofers. The exterior has scratches, bumps, etc. Serial JP01026 (Tamura Eiji)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: none
Main specifications: 240W+240W (8Ω) 480W (16Ω MONO) with peak output meter W480 × D413 × H183 mm 20.5 kg
The price has been reduced! 2024/4/23 sales price 99,800 yen genuine Rin Japan product. A network audio player. It has a simple and modern European design, so you can enjoy a bright sound without getting tired of listening. Not only is it compatible with the LINN system, but it is also equipped with digital output and variable line level output functions not found in the KLIMAX DS and AKURATE DS. There is a thin scratch on the top plate. ※The display is slightly dark, but this is the current situation. Serial 1255165 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 Operation confirmed (Ver. 4.104.518)
Accessories: remote control, power cord
Main specifications: Compatible sampling frequencies 44.1K, 48K, 88.2K, 96K, 176.4K, 192K compatible bits 16-24 bits, output terminals RCA phono (fixed/variable line level output), RCA phono coaxial (digital output) W381 x D360 x H80 mm 4 kg
The price has been drastically reduced! 2024/3/28 sales price 398,000 yen Electric has been maintained, including replacing a new windshield panel! A pre-main amplifier with a built-in McIntosh traditional output transformer. You can enjoy the rich and rich sound world typical of Macintosh. This is one that combines the appeal of the sounds of modern and old McKinn. The sense of power that makes you feel the strength is similar to that of a separate amplifier. The exterior is dull. Serial JLF1440 (Fujisawa Yukishi)
Maintenance information: 2024.4.24 Manufacturer maintained (various solder fixes on the driver board. windshield panel replacement Switch bezel fixing O ring replacement IC exchange. Capacitors were replaced at various other locations. Filter capacitor replacement. Other relays, transistors, etc. have been replaced, but please note that the pop noise of this unit is difficult to completely remove due to product specifications, so it can be heard slightly depending on when the power is turned on. Replace all front lamps. Lamp fixing grommet replacement There is a difference in meter runout when the volume is low, but when the output is raised by about 3/4, the difference is not very noticeable. Due to specifications due to individual differences in parts, improvements are difficult, so adjustments were made so that they fit at a position of approximately half a meter. Same confirmation and other inspections. *The VOL position is 05, which is the normal level of around 9 o'clock, but this is a specification. (If you are concerned, lower the CD level.)
Accessories: remote control, instruction manual
Main specifications: 150W+150W (8/4/2Ω) phono input MM dimensions W445 x H179 x D508 mm weight 30 kg
The price has been reduced! 2024/4/22 sales price 36,800 yen Quad bookshelf type speaker with a mirror finish that exudes a sense of luxury. It has wide bandwidth and cuts while retaining shadows unique to European speakers, and plays jazz and rock with rich musicality. The exterior has a feeling of use over time, such as dullness and scratches. ※This is a general-purpose jumper cable (Hiroki Aso)
Maintenance information: 2024.4.22 sound output checked (good sweep test)
Accessories: Saran net jumper cable (general purpose)
Main specifications: 2 way rear W bass reflex bookshelf type 6Ω 86db frequency characteristics 45 to 43 kHz W190 x H330 x D265 mm 6.0 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/10 sales price 69,800 yen Maintained! A stereo premain amplifier developed by inheriting CA-1000 technology. It is an amplifier that can evaluate pure sound quality without habit. The straight tone and glossy high frequencies give an impression. Even though it's an old model, it doesn't feel that the range is narrow, and it goes perfectly with rock, jazz, drums, and wind music. The exterior is dull, scratched, etc. (Tamai Jun)
Maintenance information: 2024.3.10 Maintained (speaker terminal replacement, power cord replacement, power supply circuit, tone control circuit, main amplifier circuit, etc., deterioration resistance and transistor exchange switch and volume contacts disassembly polishing input/output pin jack polishing*The circuit is not stable immediately after turning on the power supply, so when the filter or tone switch is switched, it makes a crackling sound. (If you wait a little while, it won't bother you)
Accessories: none
Main specifications: output 45W+45W (8Ω, Class B operation) 10W+10W (8Ω, Class A operation) 20Hz-20kHz power consumption rating 190W maximum 300W external dimensions 436 x H144 x D323 mm weight 13.5 kg
The price has been reduced! 2024/3/15 sales price 79,800 yen 2023/11 maintenance completed! The middle class of the Sansui α series. The strength of the bass and the sharpness of the mid to high notes are mixed in a well-balanced manner, so you can enjoy not only jazz, but also various genres such as rock and pop music. The exterior is dull and the top plate is damaged. Serial 637065630 (Tomonori Asaine)
Maintenance information: 2023.11.23 Maintained (disassembling and polishing grease applied to each switch (tone, turnover, loudness, muting, subsonic, power amplifier direct, MM/MC, reckout switch), each volume and switch clean output relay and headphone relay replacement main amplifier and power supply part solder repair, interior and exterior inspection, cleaning, side cover screw replacement operation confirmation when power is turned on It makes a popping sound, but it stabilizes in a few minutes)
Accessories: copy of instruction manual
Main specifications: effective output 160W+160W (6Ω) 130W+130W (8Ω) damping factor 100 (6Ω) W448 × H160 × D441 mm 20.3 kg
The disposal price has been reduced. Member prices are not applicable. 2024.3.28 Sales price 278,000 yen First arrival! This speaker system is the highest-end model in the reference series announced on the 25th anniversary of KEF. The expansive spatial expression and fresh, glossy sound are attractive. It seems that the previous owner replaced the woofer edge with chamois leather, so durability is also safe. *The equalizer KUBE is included, but operation has not been confirmed due to 220V specifications. Even without an equalizer, it can be used as a normal speaker without any problems. Jumper cables are replacements (Oikawa Tetsuji)
Maintenance information: 2024.3.28 Operation confirmed
Accessories: dedicated equalizer KUBE 107/2
Main specifications: 3 way 4 speakers 4 ohms 90 dB W330 x H1170 x D475 mm 45.8 kg
The price has been reduced. 2024/4/24 sales price 108,000 yen A phono equalizer amplifier equipped with a function to switch load impedance and load capacity according to the characteristics of the cartridge. Equipped with 2 line inputs, each position can be switched on the front side, and impedance settings can be adjusted with the back dip switch. The main unit is in good condition, but it is written in the instruction manual (Oikawa Tetsuji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: instruction manual, power cable
Main specifications: NF type equalizer (RIAA) input sensitivity: MM 3.2 mV, MC HIGH 0.37 mV, MC LOW 0.12 mV input impedance: MM 34 kΩ, 47 kΩ, 56 kΩ, 100 kΩ (switchable), MC HIGH 40 Ω, MC LOW 2.5 Ω input/output: 2 unbalanced systems/1 unbalanced system W364 x H81 x D274 mm 4.3 kg
Maintenance is being carried out in 2020. It's a famous machine you can't miss when talking about Marantz sounds of yesteryear. It has a good mid-range fat transfer, and its pleasant tonal feel is an appeal that cannot be obtained anywhere else. You can enjoy the Marantz sounds of the good times. There is some rust and small scratches on the exterior. Serial 8-4160 (Murakoshi Yoichi)
Maintenance information: 2020.11.18 maintained (AC code deterioration exchange, 40/40/20 μF and other deterioration replacement, 3 external paint, 20 μF x 2 deterioration exchange, selenium deterioration countermeasures → diode addition · vacuum tube 6BH6 noise exchange · vacuum tube socket and RCA jack caulking repair ※ other operation checked (measured at 32 to 41 W SP: 8 Ω with rated output AC 100 to 117 V) *A2 The EL34 vacuum tube guide pin is broken, but there is no problem with performance. (Part of the SP terminal on the right channel is missing.)
Accessories: instruction manual (for replicas, Japanese copy)
Main specifications: 35W+35W vacuum tube 6CG7/6BH6/EL34 W348 × H191 × D273mm 22.5 kg
High output MC cartridge for mono LPs only. Plays deep sound that was not produced with stereo cartridges. It has the vividness unique to Technica, but the three-dimensional effect and intensity are an appeal unique to mono (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: needle cover
Main specifications: high output MC type output 1.2 mV needle pressure 2.0 g impedance 40 ohms dead weight 6.8 g
This standard cartridge is particularly famous in the company's MC series. It has good stretch in the high range and a texture that feels good against the skin, has thickness and density in the mid-range, and it is a tone that makes you feel a sense of temperature (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: MC type output voltage 0.09 mV needle pressure 1.7 g playback frequency band 20 to 20,000 Hz load resistance 10 ohms internal impedance 3 ohms dead weight 7 g
original needle. It combines the delicate expressive power unique to light needle pressure with an energetic, thick sound typical of Type 3. Recommended for those who listen to jazz and rock (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: mm type frequency range 10 Hz to 25,000 Hz output voltage 3.5 mV needle pressure 0.75 g to 1.25 g weight 6 g
original needle. It combines the delicate expressive power unique to light needle pressure with an energetic, thick sound typical of Type 3. Recommended for those who listen to jazz and rock (Sasaki Shota)
Maintenance information: 2024.4.25 Sound output operation confirmed
Accessories: none
Main specifications: mm type frequency range 10 Hz to 25,000 Hz output voltage 3.5 mV needle pressure 0.75 g to 1.25 g weight 6 g
Comes with original box SPU synergy with the highest output in the SPU lineup. Using a G-shell containing neodymium magnets and zinc powder, it combines a modern, energetic sound with a rich sound typical of an orthophone. The stylus is good (Sasaki Shota)
Maintenance information: 2024.4.25 Sound output operation confirmed
Accessories: original box
Main specifications: MC type output voltage 0.5 mV diamond oval needle frequency characteristics 20 to 20,000 Hz needle pressure 3 g dead weight 30 g
This model commemorates the 250th anniversary of J.S. Bach's death. Uses a 6N silver wire coil. It is a cartridge that excels in even more delicate spatial expression while retaining the feel of an orthophone. The know-how of the masterpiece Jupiter has been fully introduced, and the high cost performance stands out. The cantilever is slightly to the right, and there is a small scratch and dullness on the body (Sasaki Shota)
Maintenance information: 2024.4.25 Sound output operation confirmed
Accessories: nothing
Main specifications: output voltage 0.45 mV frequency characteristics 20 Hz to 35 kHz internal resistance value 5 ohms, suitable elliptical needle pressure 2.5 g, dead weight 10 g
※The nail on the needle cover is broken, so it cannot be locked. This is BLUE from the 2M series. Ortofon's popular series with a wide range and vibrant sound. It makes you enjoy sharp sounds from popular to jazz (Hiroki Aso)
Maintenance information: 2024.4.25 storefront operation confirmed
Accessories: original box
※Since the cantilever is slightly raised, it is inexpensive. Mid-range models in the MC Star series, which come in 3 types. Both models have different sounds, and they are all unique, but 20W is a model that places particular emphasis on the mid-range. The sound is warm in tone, and has an extrusive, and comfortable sound that goes through the SPU. The wooden body made of Yamanaka lacquer, which is a traditional Japanese craft, is also beautiful.
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: MC type output voltage 0.5 mV suitable needle pressure 2.3 g recommended load impedance 10 to 200 ohms dead weight 10.5 g
Denon's classic shell. This is a genuine DA-305 shell. There is plenty of room around the lead wire, and various cartridges can be attached (Oikawa Tetsuji)
Accessories: none
Main specifications: dead weight 7g
Orthophone's classic headshell. The finger tips are ergonomically designed and are designed to be easy to operate. It is light in weight and is compatible with various cartridges and tonearms. There is a screw scratch (Oikawa Tetsuji)
Accessories: none
Main specifications: aluminum gold-plated terminals, dead weight 9.4 g
A thick, highly rigid, heavyweight shell prepared by Orthophone for cartridges other than the SPU series. The cartridge ground surface is flat, has excellent adhesion, and is an easy-to-use head shell (Oikawa Tetsuji)
Accessories: none
Main specifications: machined aluminum alloy, self-weight 16g
A head shell with a round tip that matches the MC Jubilee and Kontrapunkt cartridge shapes. Its own weight is 14.6g, which is a bit heavy (Yasuhito Koshihama)
Main specifications: machined aluminum block, dead weight 14.6 g