Comes with a magazine! A full-range unit from Stereo magazine's 2016/8 appendix. Uses Fostex's first aluminum cone diaphragm and center cap. It features good sounding and sharpness. (FUJISAWA KOSHI)
Maintenance information: 2024.5.2 operation confirmed
Accessories: gasket, magazine (original box)
Main specifications: 8cm full range unit impedance 8 ohms minimum resonance frequency 105 Hz sound pressure level 82.5 dB
※1 bottle only. A full range unit that combines an aluminum alloy HR diaphragm and a pure magnesium ridge dome diaphragm. Compared to conventional paper units, it has a slightly better transparency and microwave feel. The exterior is stained with corn paper, paint marks and scratches on the frame (Satoshi Yonejima)
Maintenance information: 2024.5.6 sweep test is good
Accessories: original box
Main specifications: impedance 4 ohms minimum resonance frequency 72 Hz playback frequency band F0 to 10 kHz output sound pressure level 85.5 dB
※1 bottle only. Maintained! This is a rare blue frame (above) model LX5. The impedance is 8 ohms, and the cross is 500 Hz, so be sure to use a 175 or 375 driver that uses 8 ohms! There are spots, rust spots, and small scratches. (Honda Maki)
Maintenance information: 2021.12.21 Conductivity confirmed 2019.4.4 Maintained (re-fix the internal coil with silicone agent. Remove rust from terminals and mounting screws, clean, and tighten. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: No accessories
Key Specifications: Crossover Frequency: 500 Hz Level Control: 3 Position Switch Input Impedance: 16 ohms 159 x 153 x 120 mm 2.3 kg
The price has been drastically reduced! 2024/4/25 sales price 69,800 yen ※Currently sold. This is an AUDIO PHYSIC superwoofer. You can enjoy very powerful bass. The crossover can also be switched between 32/46/61/80/105 Hz, which is convenient. As for the exterior, there are line scratches, saran net holes, dull stains, etc. on the top plate. Serial 573 (Yonejima Satoshi)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: spikes, saran net
Main specifications: W260 x H625 x D400 mm 26 kg
Good condition with original box! OTG cable compatible with portable devices equipped with Lightning terminals. Can be used with products equipped with USB Type-C. By using a mesh sheath that is resistant to compression and twisting, and aluminum alloy is used for the plug, faster and more stable transmission is achieved. (FUJISAWA KOSHI)
Maintenance information: 2024.2.6 continuity confirmed
Accessories: original box
Main specifications: Lightning-USB TypeC total length 138mm cable length 80mm (excluding plug)
Special stand for SX-311GY Chic grey finish It is a model that can be used with various medium speakers. Dullness, small scratches, and abrasions due to aging are conspicuous on the exterior. (YONEJIMA Satoshi)
Accessories: No accessories
Main specifications: W330 x H440 x D294 mm top plate part W267 x D245 mm 5.3 kg
※Since it is cheap, it will be handed over as is. Marantz 10cm full range speaker. There is no habit, and it makes a well-balanced sound from high to low frequencies. It doesn't take up much space, so you can set it up anywhere. The exterior has scratches, dirt, scratches, etc. Also, there is color peeling and partial deformation on saran. Serial MZ01748010115 (Fujisawa Yukishi)
Maintenance information: 2024.2.25 Operation confirmed
Accessories: saran net
Main specifications: 1 way, 1 speaker, bass reflex system, setting free type, rated input 35W, impedance 6Ω, playback frequency 50 Hz to 20 kHz, W230 x H150 x D150 mm
The price has been reduced! 2024/3/4 sales price 59,800 yen ※The diaphragm has been replaced with a genuine JBL D8R2425. Maintained! Representative of JBL's 1-inch driver units. The playback band is wide, so you can enjoy changing the network cross freely. The toughness, sound pressure, and full-bodied mid-high sound are appealing, which is unbelievable for some input. Scratch marks and paint peeling can be seen. Serial 62206, 62240 (Fujisawa Yukishi)
Maintenance information: 2024.3.4 maintained (diaphragm installation adjustment (diaphragm comes with D8R2425) genuine JBL product. (The pad dampener has been replaced.)
Accessories: No accessories
Main specifications: 1 inch driver, 500 to 20,000 Hz, 8 ohms, W145 x D97 mm, 5.1 kg/bottle
The next generation model of the L-550AX has been reviewed and refined from basic performance. We have introduced the latest technology comparable to the higher-level model L-590AX2, such as the unique ODNF 4.0 amplification feedback circuit, the new LECUA 1000, and a buffer circuit with a discrete configuration. It is a practical modern machine with enhanced resolution while acquiring the glossy and dense sound unique to pure A class amplification systems. The exterior is good with no conspicuous scratches. Serial G60500154 (Yonejima Satoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: remote control, instruction manual, power cord
Main specifications: rated output 20W+20W (8Ω) 40W+40W (4Ω) W440 × H178 × D454 mm 24.3 kg
All internal deteriorated capacitors and parts have been replaced! Furthermore, a new dust cover has also been created so you can use it comfortably. A masterpiece model of a semi-auto player. The torque and braking power of the motor are excellent, and the stability of operation is impressive. The sound quality, which is delicate and has an excellent sense of resolution, brings out the performance of the cartridge well. There are thin threads on the exterior. Serial 10700499 (Yonejima Satoshi)
Maintenance information: 2024.2.29 Maintained (new dust cover created, motor part removed, shaft and bearing cleaned and lubricated. The tact SW on the operation part and the electrolytic capacitor on the internal board were replaced with a new one. Resolder the board. Remove the area around the arm, clean each part after disassembly, replace the shaft bearing, inspect the internal lead wire, and reassemble. Dust cover hinge reinforcement bracket created. Exterior cleaning, cabinet scratch polishing, rotation speed check, operation test of each part, sound test)
Accessories: instruction manual, screws, EP adapter
Main Specifications: Quartz Lock DD Drive Auto Lift Up Static Balance Type Compatible Cartridge Weight 2 to 12 g Needle Pressure Range 0 to 3 g W490 x H182 x D410 mm 14.5 kg
※Operation has been confirmed, but since it is cheap, it will be handed over as is. This is a KENWOOD KA series amplifier. It has a compact and clean design, and can be placed horizontally or vertically. The sound quality is as clean as it looks, and it is recommended for those who want to enjoy music in a small space. Serial 61100061 (Sato Wataru)
Maintenance information: 2024.3.26 Operation confirmed
Accessories: No accessories
Main specifications: 3 input lines 12W+12W (8Ω) dimensions W171 x H67 x D207 mm weight 2 kg
An affordable Lax interconnect cable with attention to detail, such as each core structure that makes the hot and cold of the 1.0 m RCA cable transmission line the same, and a core wire wrapped in Japanese paper. It is characterized by its moderate thickness and good S/N. (YONEJIMA Satoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: No accessories
The price has been drastically reduced! 2024/5/15 sales price 198,000 yen 800 Diamond series center speaker It is well connected to the Diamond Series due to unit groups that have evolved further from the previous game. High quality mid-range is reproduced. It is a cheap character that can be combined with other speakers for the center. There are thin threads on the exterior. Serial 12120002808 (Yonejima Satoshi)
Maintenance information: 2024.5.15 sweep test good
Accessories: jumper cable
Main specifications: 2-way bass reflex drive unit 25mm diamond dome tweeter x 1, 165mm Woben Kevlar cone FST mid woofer x 1 playback frequency band 42Hz to 33kHz output sound pressure level 88dB nominal impedance 8Ω W486 x H279 x D287 mm weight 12.5 kg
It is a headphone amplifier with separate power supply with a preamp function. Genuine Naspec. It is compatible with most commercially available headphones, and high sound quality playback is possible even with inner-earphones or authentic stereo headphones. There are small scratches and dullness on the exterior. Serial KRHQ1200069/KRHQP120069 (Yonejima Satoshi)
Maintenance information: 2024.5.16 Operation confirmed
Accessories: power cord, connection cord
Main Specifications: Dynamic Range 110dB SNR 115dB Output Impedance 8Ω Body: W185 x D175 x 53mm 1.0 kg Power Supply Unit: H185 x D150 x H53 mm 1.7 kg
※Since it is cheap, it will be handed over as is. Chinese vacuum tube amplifiers have arrived. The vacuum tube uses FU32, and is compact and designed to be just the right size for a desktop, etc. There is a thread on the exterior (Tamura Eiji)
Maintenance information: 2024.5.16 Operation confirmed
Accessories: none
Main specifications: 4W x 2 (4Ω) frequency response 26 to 38 kHz W296 x H150 x D210 mm weight 5.7 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/21 sales price 99,800 yen DALI's HELICON series center speaker. If you use the company's HELICON series and are considering surround, please give it a try. The exterior is dull. Serial 7660180 (Fujisawa Yukishi)
Maintenance information: 2024.4.21 operation confirmed
Accessories: original box, saran net
Main specifications: 4Ω playback frequency band 49Hz to 27kHz W650 ✕ H210 ✕ D435mm weight 18.4 kg
A compact, high CP, and easy headphone amplifier. The sound is bright and has good visibility. A well-balanced model that works well with everything from pop to rock. Serial 32741 (Fujisawa Yukishi)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: instruction manual, AC adapter
Main specifications: output 330 mw/30 ohm, 60 mw/300 ohm headphone amplifier connection, 30 ohm gain, 11 dB S/N ratio, 87 dB frequency characteristics, 30 to 20 kHz, input/output RCA, 1 system each, W103 x D127 x H38 mm, 1.40 kg
*The HDD has been changed to an SSD (2TB). This is a black model that has upgraded the DELA N1A/N1Z, which was announced and sold as the industry's first “audio NAS,” and improved commerciality. Equipped with a dedicated USB-DAC connection terminal, the rear design has been renewed. In addition to being equipped with a 60W high-capacity power supply unit, a newly developed high-capacity capacitor bank is mounted on the rear stage of the power supply unit. A newly selected 3.5-inch quiet drive is mounted on a floating silicon bush to improve sound quality. There are scuff marks and dirt marks on the exterior. Serial 40300161000139 (Fujisawa Yukishi)
Maintenance information: 2024.5.17 Operation confirmed
Accessories: power cord
Main specifications: storage capacity 2TB (2TB SSD x 1) input/output terminal USB 3.0 x 3 (import/capacity expansion/backup) USB 2.0 x 1 (for USB-DAC connection) RJ45 x 2 (router connection/network player) compatible file format WAV · AIFF · FLAC · ALAC · DSF · DFF sample frequency 44.1/88.2/176.4/352.8/48/96/192/384 kHz (PCM) 2.8 /5.6/11.3 MHz (DSD) compatible bits 16 to 32 bits (PCM) W436 x H70 x D352 mm weight 7 kg
5cm full range enclosure It's a backroad type and small, perfect size for those who want to play. It seems to be useful for desktops, etc. There are stains and bumps on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: baffle hole diameter φ54 mm W127 x H154 x D170 mm weight 1.0 kg/1 bottle
Power cable 1.8 m PSE standard 5-core power cable using PCUHD and 4N-OFC. The plug is a 2P type that uses brass+rhodium plating. Thick, orthodox sound. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Power cable 1.8 m PSE standard 5-core power cable using PCUHD and 4N-OFC. The plug is a 2P type that uses brass+rhodium plating. Thick, orthodox sound. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Power cable 1.8 m PSE standard 5-core power cable using PCUHD and 4N-OFC. The plug is a 2P type that uses brass+rhodium plating. Thick, orthodox sound. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
It is a USB-connected bus-powered D/D converter that uses the C-Media “CM6642” as the digital audio control IC and is compatible with high-resolution sound sources (maximum 24 bit/192 kHz) (Tamura Eiji)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, original box
Main specifications: digital input: USB TypeB terminal USB 1.1/2.0 compatible, USBAudioClass 1.0/2.0 compatible digital output: coaxial digital audio output (COAXIAL) optical digital audio input (square) compatible format: PCM maximum 24 bit 192 kHz W40 x H25 x 81 mm 90 g
Flat speaker with 600 neodymium magnets. It is built into a self-made enclosure. It is an audio speaker that is mainly used outdoors for station announcements and as a large digital signage product for outdoor use. As for the exterior, there are screw holes in the top plate, and there are dullness and small scratches all over (Yonejima Satoshi)
Maintenance information: 2024.5.18 sweep test good
Accessories: No accessories
Main specifications: MCMA multi-cell flat speaker impedance 8Ω frequency specification 90Hz to 10kHz W270 x H375 x D205 mm 5.2 kg [actual measurement)
The price has been reduced! 2023/5/15 sales price 19,800 yen A new-concept connected tap equipped with a surge absorber (lightning protection) and noise filter in one package. It has contributed greatly to further improvements in S/N and sharp sound quality that is transparent yet makes you feel dynamic. There are no noticeable scratches on the exterior. Serial 38600KK042 (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Main specifications: W56 x H35 x D233 mm (including connected outlets) 620 g
3P inlet plug Pure copper with high conductivity is used for the blade to ensure rigidity. The contacts are models that use rhodium plating treatment and α-process treatment (ultra-low temperature treatment & special electromagnetic field treatment). (TAMURA Eiji)
Accessories: case
F series tall boy speaker from British Celestion. It can be used for a wide range of purposes, from AV systems to pure audio. It is a bright tone with a pleasant drop and spread of the midrange. There is no effect on operation, but there is a dent in the mid-range center dome on one side. (FUJISAWA KOSHI)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: instruction manual (English characters), saran net, spikes, jumper plates
Main specifications: 3-way bass reflex type output sound pressure level: 90db 8Ω W264 × H920 × D342 mm 20 kg
An XLR cable 0.6 m pair uses the world's most advanced virtual coaxial structure, and by using the same structure as a line cable as well as a microphone cable, it achieves low capacitance and broadband transmission (Satoshi Yonejima)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
The disposal price has been reduced! (Member prices are not applicable) 2024/4/28 sales price 99,800 yen D/A converter with a dual monaural configuration equipped with 2 “ES9038PRO” units. Using 3 Talema toroidal transformers, you can feel the creator's commitment. More natural sound can be reproduced. On the exterior, there are noticeable line marks on the top plate (Tamura Eiji)
Maintenance information: 2024.4.28 Operation confirmed
Accessories: power cable
Main Specifications: Coaxial/BNC/AES/Optical: PCM44.1k to 192 K/16 to 24 bit, DOP64 I2S Input: RJ45/HDMI PCM44.1K to 768K 24/32 bit DSD64 to DSD1024 DOP64 to 256 W430 x H80 x D335 mm Weight 5.4 kg
*Currently sold. Technics 5cm horn tweeter Uses titanium diaphragms and die-cast aluminum horns. The sound quality is bright and hard with good sharpness. There are scratches and oxidation on the exterior (Yonejima Satoshi)
Maintenance information: 2024.5.19 oscillator test is good
Accessories: No accessories
Main specifications: horn type playback frequency 3,000 to 25,000 Hz W70 x H70 x D60 mm 0.35 kg
The price has been reduced! 2023/5/11 sales price 49,800 yen ※Since manufacturer repairs are not possible, it will be sold as is. The remote control is now in stock. It is a compact premain amplifier equipped with plenty of inputs in a 214mm half-size housing. Compatible with a total of 3 digital inputs, 1 optical 2 coaxial, USB input up to 192 kHz/24 bit, and Bluetooth audio transmission. It is compatible with all kinds of music sources. The exterior is dull. Serial 53330E001473 (Yonejima Satoshi)
Maintenance information: 2024.5.9 operation confirmed
Accessories: instruction manual (English characters), power cord, remote control
Main specifications: output 80W x 2ch (4Ω) output terminal subwoofer x 1/headphone x 1/input terminal LINE x 2/COAXIAL x 1/OPTICAL x 2/USB x 1 digital input USB maximum 192 kHz/24 bit COAX/OPTICAL maximum 192 kHz/24 bit other Bluetooth audio compatible (A2DP with aptX) W214 x H60 x D284 mm mass 2.8 kg
It is a 75 ohm coaxial cable with 0.7 m RCA terminals and a double shielded “cordel structure” that minimizes dielectric loss. The exterior is dull, part 1 characters are missing, etc. (Fujisawa Yukishi)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: original bag
*Currently sold. Woofer edge softened A model developed with an eye on the digital age. The natural spread of sound is suitable not only for vocals, but also for classical music, etc. This is a volume-input high CP model unique to the bubble period. The exterior has a saran net hole, and the emblem is missing on one side and the other side is missing. Also, the veneer is torn. Serial 2609/12502 (Yonejima Satoshi)
Maintenance information: 2024.5.5 maintained (woofer edge softening treatment, good sweep test)
Accessories: saran net
Main specifications: 3 way 3 speakers, sealed, 32 cm for the low range, 10 cm, cone type/2.5 cm for the high range, dome type frequency band 35 Hz to 30 kHz crossover 600 Hz/5 kHz sound pressure level 91 dB impedance 6 Ω dimensions W370 x H680 x D330 mm weight 21 kg/book
Woofer edge softening treatment! A mid-size dia-tone speaker. The sound image expressed from precise sound construction is carefully created with diamond tones, making classical music elegant and magnificent. Female vocals etc. are also recommended. There are small scratches, scuffs, and broken corners on the net. Serial 19119, 19433 (Fujisawa Yukishi)
Maintenance Information: 2024.5.20 Maintained (woofer edge softening treatment)
Accessories: saran net
Main specifications: 3 way, 3 speakers, sealed frequency band, 35 Hz to 40 kHz, 6 ohms, sound pressure level, 90 dB, W360 x H808 x D325 mm, 29 kg/book
*Fully automatic player with built-in Denon phono equalizer currently sold. It is recommended for those who want to enjoy records casually without worrying about the location, or for beginners. The exterior is dull and has scratches. Serial 8043308382 (Yonejima Satoshi)
Maintenance information: 2024.1.4 operation confirmed
Accessories: No accessories
Main specifications: fully automatic player belt drive, suitable needle pressure 3.5 g, W360 ✕ H ✕ D370 mm, weight 2.9 kg
Exclusive stand for the DS-77HR sold separately. Of course, it is also recommended for other medium speakers. The exterior has creases, floats, scratches, etc. (Tamura Eiji)
Accessories: No accessories
Main specifications: W410 x H264 x D330 mm weight 10 kg
It is a DIGIMASTER X64.4 linked to the famous 2000SH4 series. The thick, elastic sound unique to WADIA's heyday is attractive. It is a high-end aircraft of the time with high musicality, and also has intense colors. The exterior is dull. The exterior has scratches, etc. Genuine AXISS Serial 1 2011-90 (Yonejima Satoshi)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: copy of instruction manual, power cable, connection cord
Main Specifications: Sledgehammer Buffer Drive Resampling Rate 64X Resolution 18 Bits CPU Power 72 MIPS Sampling Frequency 32/44.1/48kHz Input: 2 Coaxial (BNC) Systems, 2 Optical Systems Output: 1 Unbalanced (RCA) System, 1 Balance (XLR) System W486 x H89 x D381 mm Weight 12 kg
※1 bottle only. Currently sold. A full range of 8cm high grade glass cloth cones. It has a light, unobtrusive sound and is recommended for pop music and female vocals. The exterior is dull. (YONEJIMA Satoshi)
Maintenance information: 2024.2.17 sweep test good
Accessories: No accessories
Main specifications: 6Ω 84dB 20W 0.54 kg
The CD mechanism has been replaced at Denon! Denon design series CD player. It is equipped with an inexpensive yet highly accurate D/A converter that is compatible with MP3 and WMA files. Since it can also be used vertically, it is attractive that it is easy to adjust where it is placed. The exterior is dull and has small scratches. Serial ADR 27190603014 (Tamura Eiji)
Maintenance information: 2024.5.16 manufacturer maintained
Accessories: remote control, power cable
Main specifications: analog output x 1, coaxial digital output x 1 size W200 x H86 x D 240 mm, weight 2.4 kg
1650 series SACD/CD player It is a model with a low, loud sound that makes you feel a sense of depth and scale. There is also a digital input terminal, and it can also be used as a standalone D/A converter compatible with sampling frequencies of 32 to 192 kHz. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.5.9 operation confirmed
Accessories: remote control, power cable
Main specifications: Super Audio CD section/1 bit DSD system Playback frequency approx. 2 Hz to 50 kHz SNR 119 dB CD section/playback frequency approx. 2 Hz to 20 kHz W434 x H137 x D336 mm 13.5 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/9 sales price 99,800 yen with wood horn! Maintained! An integrated mid-range driver unit developed for 3-way use. It's an energetic and clear sound typical of YL. Paint peeling can be seen in places. Serial 751903, 751903 (Fujisawa Yukishi)
Maintenance information: 2024.4.9 maintained (coil roundness adjustment, noise suppression, porcelain circuit slit maintenance)
Accessories: No accessories
Main specifications: Playback frequency band 800 to 8,000 Hz maximum input 40W 8Ω output sound pressure level 101 dB outer diameter W400 × H200 × D350 mm 3.30 kg
A fully balanced discrete, non-feedback D/A converter using an independent mono mode that is also equipped with a NOS mode. Equipped with 2 ESS ES9038PRO In addition to being compatible with the latest high-resolution sound sources in various PCM and DSD formats via USB input, it also supports coaxial digital input (2 systems) AES/EBU input. You can enjoy more realistic and natural sounds in NOS mode. There are several dot-shaped dents on the front panel. Serial 190730008 (Fujisawa Yukishi)
Maintenance information: 2024.5.20 Operation confirmed (the mounting solder was fixed because the RCA terminal ground cap came off.)
Accessories: instruction manual, power cord, spike
Main specifications: input format (USB) PCM, DSD (DoP v1.1, ASIO) input format (coaxial/AES/EBU) PCM, DSD (DoP v1.1) compatible sampling frequency (USB) maximum 768 kHz (PCM) /maximum 22.6 MHz (DSD) compatible sampling frequency (coaxial/AES/EBU) maximum 192 kHz (PCM) /2.8 MHz (DSD64 DoP v1.1) PCM quantization Number of bits (USB) 24 bit 32 bit PCM number of quantized bits (coaxial/AES/EBU) 16 bit 24 bit USB profile USB 2.0, USB Audio 2.0 digital input USB (Type B) 2 coaxial (SPDIF) AES/EBU analog output XLR1 system RCA1 system analog output level (XLR) 5.6 Vrms analog output level (RCA) 2.8 Vrms frequency characteristics 2 Hz to 120 kHz (+0/-1 dB) S/N ratio 110 dB total harmonic distortion ratio 0.003% analog filter secondary passive power supply voltage AC 100V 50/60 Hz power consumption 40W size W430 x H109 x D379 mm weight 10 kg
Quadra Spire Center Speaker Stand This stand allows you to adjust the angle according to the listening position. As for the exterior, felt is attached to the bottom (Tamura Eiji)
Accessories: No accessories
Main specifications: W375 x H111 x D290 mm
Entry model for Caldas with 2.0m pair of speaker cables, single with Y-lug specification on one side and bi-wire on the other side, 4-core structure. The resolution is also extremely high, and it is characteristic that it is smooth and has a high sense of transparency. (FUJISAWA KOSHI)
Maintenance information: 2024.5.12 continuity confirmed
Accessories: No accessories
Speaker cable is a current CARDAS entry series speaker cable with an unprocessed 4-core structure with 1.5 m pair terminals. Use Perfect Surface Copper. The high frequency extension of the single line and the Ritz line is an appeal that cannot be obtained anywhere else. (FUJISAWA KOSHI)
Maintenance information: 2024.5.18 continuity confirmed
Accessories: No accessories
※ Because it is cheap, it is currently sold. JBL 2-way speaker. It is a large, well-balanced model that is easy to use. It is also recommended as a speaker for BGM in stores, etc. On the exterior, there are stains and adhesive marks on the edges. Also, there are some holes on the sides. Serial 121213353121213 (Yonejima Satoshi)
Maintenance information: 2024.5.19 sweep test good
Accessories: grill net
Main specifications: W152 × H232 × D140 mm 2.5 kg
The disposal price has been reduced! Member prices are not applicable. 2024/4/12 sales price 79,800 yen ※It is cheap because it is in poor condition. Equipped with a coaxial unit, sound localization is good, the high frequencies are clear, and the sense of volume in the low frequencies is sufficient for the size, so you can relax and listen to classical music in small groups. It also has good efficiency, so it's easy to play, and it features a chic design with a shiny mirror piano paint. In addition to being scratched, some Saran magnets are missing. Also, there is a slight wobble in the SP terminal on the + side on one side, and one screw that stops the terminal board is missing. (FUJISAWA KOSHI)
Maintenance information: 2024.4.9 operation confirmed
Accessories: saran net
Main specifications: 36Hz to 22kHz 45W 4Ω 93.5dB W207 × H990 × D274 mm 17 kg
Mini plug to stereo standard plug conversion cable It is a model using OFC as a wire rod. (Eiji Tamura)
Maintenance information: 2022.1.5 continuity confirmed
Accessories: original box