The price has been reduced! 2024/4/13 sales price 69,800 yen ※It is cheap because it has a tobacco smell. It is a premain amplifier with a built-in USB DAC compatible with a maximum DSD of 11.2 MHz and PCM384 kHz/32 bit input. Adopts a dual monaural configuration/fully balanced circuit design that inherits the design philosophy of the UD-503. This one is enough, and it's a convenient dish. There are small scratches on the exterior. Serial 1710182 (Tamura Eiji)
Maintenance information: 2024.4.13 operation confirmed
Accessories: remote control, power cable
Main specifications: 20W+20W (8Ω) impedance 4Ω to 8Ω frequency characteristics 10Hz to 100kHz W290 x J81.2 x D264 mm mass 3.7 kg
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
Maintained! A pre-main amplifier that inherits the sound of the D series and has achieved even lower distortion. A model where you can feel the uniqueness of Sansui at the time in the extrusion of low frequencies and sound creation. It's energetic, playable, and goes great with jazz and rock, and is compatible not only with MMs but also with MC, making it great for analog fans. There is a feeling of use such as dullness, abrasions, corrosion, dirt, etc. (Kobayashi Hitoshi)
Maintenance information: 2023.11.21 Maintained (balance, main volume, output relay, power supply floating resistor, Mylar capacitor, equalizer section op amp replaced. Input selector and other rec outs, tone, subsonic, and muting switches are disassembled and polished grease is applied. (Each volume, switch cleaning, solder repair, interior and exterior inspection and cleaning, adjustment inspection.)
Accessories: copy of the instruction manual
Main specifications: 75W+75W (8Ω) PHONO (MM/MC) W445 x H163 x D403 mm 12.4 kg
Maintained. The successor that inherited the sound of the D series. A model where you can feel the uniqueness of Sansui at the time due to the extrusion of low frequencies and the creation of sound. They are energetic, playable, and go great with jazz and rock, and are compatible not only with MM but also with MC, making analog fans happy. There is dirt on the top plate (Sasaki Shota)
Maintenance information: 2024.2.8 maintained (main amplifier circuit transistor, film capacitor, DC, bias semi-fixed volume replacement, output relay replacement, power supply circuit floating resistor replacement, balance volume exchange, input selector, reck-out, tone switch disassembly polishing grease application, each volume, switch cleaning, interior and exterior inspection cleaning, pin jack polishing, adjustment inspection)
Accessories: none
Main specifications: execution output 80W+80W (8Ω) damping factor 100 rated power consumption 200W phono MM/MC compatible W460 x H160 x D404 mm weight 13.2 kg
Maintained! The mid-range α series uses an α-X balance circuit that blocks the effects of noise and distortion from the ground. The smooth, stretchy sound quality is attractive. Designed with CD playback in mind, the sound separation is good, and it is a classic premain that will keep you entertained regardless of genre. The exterior has rust spots, paint bald, etc. (Mizusaki Ryo)
Maintenance information: 2023.2.1 maintained (main amplifier output relay replacement, transistor and capacitor replacement, MM/MC, reckout switch disassembly, polishing grease application, solder main part repair, various volumes, switch cleaning, interior and exterior inspection cleaning, offset adjustment, operation inspection)
Accessories: copy of instruction manual
Main specifications: 90W+90W (8Ω) W448 x H160 x D441 mm 16.0 kg
Maintained! A pre-main amplifier that allows you to enjoy the glossy and thick sound typical of Sansui. What is noteworthy is the mid-low range, and the bass line, which clearly reveals the outline, is an appeal unique to the KX series during this period. The exterior is dull and has a feeling of use (Hiura Katsuji)
Maintenance information: 2024.4.20 maintenance (output relay replacement, power amplifier circuit resistance replacement, power supply circuit capacitor replacement, tape selector, etc., switch disassembly, polishing grease application (input selector, power amplifier direct, source direct, reck-out, tone, loudness, muting switch), various volumes, switch cleaning, solder main part repair, pin jack polishing, interior and exterior inspection, cleaning, operation confirm)
Accessories: copy of instruction manual
Main specifications: 90W+90W (8Ω) phono mm/MC compatible dimensions W430 x H161 x D446 mm weight 18.0 kg
The price has been reduced! 2024/3/15 sales price 79,800 yen 2023/11 maintenance completed! The middle class of the Sansui α series. The strength of the bass and the sharpness of the mid to high notes are mixed in a well-balanced manner, so you can enjoy not only jazz, but also various genres such as rock and pop music. The exterior is dull and the top plate is damaged. Serial 637065630 (Tomonori Asaine)
Maintenance information: 2023.11.23 Maintained (disassembling and polishing grease applied to each switch (tone, turnover, loudness, muting, subsonic, power amplifier direct, MM/MC, reckout switch), each volume and switch clean output relay and headphone relay replacement main amplifier and power supply part solder repair, interior and exterior inspection, cleaning, side cover screw replacement operation confirmation when power is turned on It makes a popping sound, but it stabilizes in a few minutes)
Accessories: copy of instruction manual
Main specifications: effective output 160W+160W (6Ω) 130W+130W (8Ω) damping factor 100 (6Ω) W448 × H160 × D441 mm 20.3 kg
Maintained! This is a 907 series higher class premain amplifier. Not only is the sound thick and wide range, but it is also a deep and majestic sound with a sense of weight. The XR series during this period has particularly horsepower in the mid to low range, and it sounds briskly ROCK and JAZZ. The exterior is dull and has a feeling of use (Hiura Katsuji)
Maintenance information: 2024.4.20 maintenance (main amplifier circuit transistor, adjustment volume exchange, output relay, headphone relay replacement, power supply circuit transistor replacement, input selector, etc., and application of polishing grease (power amplifier direct, source direct, reck-out, tape, loudness, subsonic, muting, processor switch), various volume cleaning, soldering (Repair, DC, bias adjustment, internal inspection and cleaning, operation confirmation)
Accessories: instruction manual
Main specifications: Equipped with HYPERα-X balance circuit, effective output 190 w+190 w dimensions W466 x H163 x D452 mm, weight 33 kg
The price has been reduced. The 2024/4/24 sales price 298,000 yen optional phono card is not installed. In North America, CLASSE is a popular brand along with McIntosh and KRELL. Since it has straight expressiveness and driving ability, it reproduces a rich sense of sound field. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.19 Operation confirmed
Accessories: remote control, power cable
Main specifications: maximum output 100W x 2 (8Ω), 200W x 2 (4Ω) input unbalanced 4 systems, balance 1 system power consumption 260W (rated) W445 x H121 x D419mm 23.0 kg
*Since the digital input circuit module cannot be repaired, the digital input cannot be used. Maintained! Kenwood pre-main amplifier. It plays clear, transparent mid-high frequencies and low frequencies with a firm sense of power typical of Kenwood in a well-balanced manner. There is an air cap mark on the top of the front panel. (KOBAYASHI Hitoshi)
Maintenance information: 2024.4.24 Maintained (input board connector correction, switch correction, contact correction, operation confirmation) 2023.5.21 Maintained (display lamp replacement. Switch and volume contact correction. (*The digital circuit module is broken, but the digital input cannot be used because it is not available)
Accessories: none
Main specifications: 150W+150W (8Ω) phonomC/mm mounted damping factor 1000 W 476 x H170 x D424 mm 19.7 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/2/29 sales price 128,000 yen A digital amplifier equipped with a Tripath class T PWM amplifier IC. It beautifully expresses the sense of energy and description. Gain can also be switched on the back, and it is compatible with a wide range of input sources. The exterior is dull and there are scratches on the top of the front panel. Serial 090120022 (Tomonori Asaine)
Maintenance information: 2024.2.27 sound output confirmed
Accessories: power cord instruction manual
Main specifications: output 150W+150W (8Ω) 240W+240W (4Ω) W420 x H98 x D395 mm weight 13 kg
A new-generation integrated upgrade that brings out the appeal of unique speakers as much as possible by raising the damping factor to 600 and bringing out the appeal of unique speakers as much as possible. The power amplification stage with 3 parallel push-pull power MOSFETs allows you to hear more powerful sound than before. There are no noticeable scratches on the exterior. Serial B0X159 (Fujisawa Yukishi)
Maintenance information: 2024.4.20 Operation confirmed
Accessories: remote control, instruction manual, power cord, original box
Main specifications: rated output 180W+180W (8Ω) input RCA5 systems, XLR2 system, tape input/output 1 system, pre-out RCA1 system, XLR1 system main in RCA1 system, XLR1 system damping factor 600 size W465 ✕ H181 ✕ D428mm weight 24.6 kg
The price has been reduced! 2024/4/13 sales price 35,000 yen Maintained! A premain amplifier with an impressive warm color sound while keeping the clear, easy-to-see sound typical of ONKYO. Recommended for classical music, female vocals, etc. There are dullness over time, scratches, etc. (Daiki Goto)
Maintenance information: 2023.10.17 Maintained (maintenance contents/tone, reck-out, MM/MC switch disassembly, polishing grease application, main amplifier part solder repair, output relay replacement, volume, switch cleaning, pin jack polishing, input/output confirmation, operation confirmation. (Even after tone SW decomposition and polishing treatment, a small pop sound is made when turned on and off, but there are no interruptions in the sound.)
Accessories: copy of instruction manual
Main specifications: W435 x H164 x D434 mm 14.9 kg
The price has been reduced! 2024/2/15 sales price 45,000 yen Maintained! ONKYO premain amplifier with high cost performance. A non-feedback power amplifier is used, and the power supply transformer is of high quality and carefully crafted. The power amplifier direct position allows direct input to the power amplifier via volume only. The exterior is dull. Serial 4604014114 (Yonejima Satoshi)
Maintenance information: 2024.2.15 Maintained (input selector, direct switch, etc. Switch disassemble contacts, polish contacts and apply contact cleaner. Main amplifier circuit input circuit soldering correction)
Accessories: instruction manual
Main specifications: 100W+100W (8Ω) PHONO input 1 system (MM/ MC switching) W445 x H165 x D434 mm 18.0 kg